Item #1000051056 Model #S5-BRH00800 USE AND CARE GUIDE NILES PARK FIREPIT Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 6 p.m., EST, Monday - Friday 855-HD-HAMPTON HAMPTONBAY.COM CSA Model99010 THANK YOU quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Table of Contents Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Save These Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Information - Propane (LP) Gas. . . . . . . . . . 3 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information (continued) IMPORTANT SAFETY INFORMATION PROPANE (LP) GAS CAUTION: The propane gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 11 in. water column. A self-contained LP gas cylinder for use with this appliance must have a capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD (overfill protection device).
Warranty 2-YEAR LIMITED WARRANTY WHAT IS COVERED The item you have purchased is warranted against defects in materials and workmanship for the following parts as outlined below only when the unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes: □□ Burner Assembly □□ Firepit Base □□ Firepit Top HOW DO I OBTAIN WARRANTY SERVICE? To obtain warranty service, you must contact our customer service center within the relevant
Pre-Assembly PLANNING ASSEMBLY Identify parts packed in the carton against the parts list. Remove all protective materials and set parts on a flat, non-abrasive surface. If any part appears missing or damaged, do not assemble or use this product. Contact the Customer Service Team at 1-855-HD-HAMPTON. SPECIFICATIONS Input 40,000 BTU/hr Propane Regulator Pressure 11 in. water column Clearances to Combustible Surfaces Sides: 24 in./61 cm 30,000 BTU/hr Low fire Top: 72 in.
Pre-Assembly (continued) PACKAGE CONTENTS L R A D M J N T B P C E F G S O T H K Q Part Description Part # Quantity Part A Control knob* FP0245 1 B Gas valve* FP0307 C Thermocouple* FP0004 D LP Regulator hose FP0308 E Electrode* F G Ignition module* H I Description Part # Quantity K Footcap FC0743 4 1 L Tabletop FP1169 1 1 M Back panel FP1170 1 1 N Left side panel FP1171 1 FP0003 1 O Right side panel FP1172 1 FP0310 1 P Door panel FP1173 1 FP
Assembly 1 2 Assembling the side panels □ Attach the back panel (M) to the left and right side panels (N and O) using four ¼ in. x 45 mm bolts (BB) and washers (EE). Guide the bolts (BB) through the holes in the back panel (M) and into the pre-drilled holes in the side panels (N and O). Hand tighten only. Attaching the middle support □ Attach the middle support (S) to the side panels (N and O) using two ¼ in. x 15 mm bolts (AA) and washers (EE).
Assembly (continued) 5 6 Attaching the table top □ With the help of another person, carefully place the table top (L) onto the assembly. After making any necessary adjustments to the alignment of the table top and the assembled base, use four ¼ in. x 15 mm bolts (AA) and washers (EE). Guide the bolts (AA) through the holes in the side panels and into the pre-drilled holes under the table top (L). Do not tighten completely.
Assembly (continued) 9 10 Placing the lava rocks Tightening bolts and placing the tiles □ After making any necessary adjustments to the parts, use the hex wrench (CC) to tighten all bolts (AA and BB). Tighten each bolt a few revolutions at a time. Repeat until all bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts with covers (DD). See the illustrations in steps 1 - 8 for proper placement of the bolt covers (DD). □ Pour the lava rocks (J) into the burner.
Lighting a Fire WARNING: If these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. 1. Make sure the control knob is in the “OFF” position. Open the tank valve all the way. 2. Push in the igniter button. You will hear a slight clicking sound. With the igniter button pushed in, push and turn the control knob to the “ON” position. The fire should light within a few seconds.
Troubleshooting Problem Probable Cause The burner does not light. There is no propane gas at the burner. Check that the gas tank valve is open. Turn the control knob to the “ON” position and push the control knob in. Make sure the tank has propane gas. There is no spark at the electrode. Check that the AAA battery is installed with the negative (-) end first and has a charge. Check that the wire is connected to the ignition module. Check that the electrode is not cracked or broken.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m.-6 p.m., EST, Monday-Friday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
Item #1000051056 Model #S5-BRH00800 USE AND CARE GUIDE NILES PARK INSIDE ROCKER Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 6 p.m., EST, Monday - Friday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this rocker. We strive to continually create quality products designed to enhance your home.
Table of Contents Table of Contents ................................2 Warranty ..............................................2 What is Covered .....................................2 What is Not Covered ...............................2 Pre-Assembly ......................................3 Planning Assembly..................................3 Hardware Included..................................3 Package Contents...................................4 Assembly.............................................
Pre-Assembly PLANNING ASSEMBLY Identify all parts packed in the carton against the parts list. Remove all protective materials. Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are unsure how to proceed with the assembly, call our Customer Service Team at 1-855-HD-HAMPTON. Do not attempt assembly if any parts are missing or damaged. Two people may be required to assemble the rocker.
Pre-Assembly (continued) PACKAGE CONTENTS A B2 B1 D C Part Description Order Part # Quantity A Chair Frame AR19764 1 B1 Left Leg AR19765 1 B2 Right Leg AR19766 1 C Support Bar AR19767 1 D Leg Support AR19768 1 4
Assembly ASSEMBLY NOTE: The “Left” and “Right” legs are determined facing the rocker, not sitting in the rocker. We recommend two people work together to assemble this item. Make sure arrows from both the “U” bar and rocker assembly are pointing in the same direction! 1 □ □ □ 2 Attaching the leg Attach the leg support (D) to the chair legs (B1 and B2) by using the 1/4 in. x 20 mm bolts (AA). Guide the bolts through the holes in the leg support (D), into the pre-drilled holes in the chair (B1 and B2).
Maintenance FRAME: Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain the frames, remove the foot caps and tilt the frames, if necessary, to remove all water. This is critical. Water allowed to accumulate inside the frames and then exposed to sub-freezing temperatures can cause damage to the frame tubing. Such damage is not covered under the warranty. Always clean, drain, and dry thoroughly before storing for the winter.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 6 p.m., EST, Monday - Friday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
