Installation Guide

ManualsBrandsHampton Bay ManualsOutdoorsCarol Stream Spectrum Cilantro Patio Lounge Seating with Bar Table

AFL04112

Page 2

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!

TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT

PARTS LIST DESCRIPTION ORDER PART #

QTY

BOLT COVER

HEX BOLT DRIVER

RIGHT ARM

BACK FRAME

HW0105

HW0004

HW0006

* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE

Ø6.5 X 1.0 MM

WASHER

1/4" X 20 MM BOLT

HW0036

Figure 1

Step 1: Identify parts packed in carton against the parts list.

Remove all protective materials and set parts on a flat,

non-abrasive surface.

Step 2:

igure

If you are missing any parts or

are unsure how to proceed with assembly, call our

Customer Service Center at 1-800-416-3511.

Attach the seat frame to the left leg by using four

1/4"x30 mm bolts and washers as shown in F 1.

Guide the bolts through the holes in seat frame, into the

pre-drilled holes in the left leg. Hand tighten only.

Attach the support bar-1 and support bar-2 to the left leg

by using four 1/4"x20 mm bolts and washers as shown

in F 2. Hand tighten only. Attach the back to the

left leg by using one 1/4"x20 mm bolt and washer as

shown in F 3. Hand tighten only.

Do not

attempt to assemble table if any parts are missing

or damaged.

Step 4: After making any necessary adjustments to the alignment of the

chair, use the hex bolt driver to tighten all bolts. Note: each

bolt must be tightened a few revolutions at a time. In order to

apply equal pressure to all bolt joints, we recommend working

in a cross corner (X) fashion. Repeat until all bolts are tight.

Do not over tighten. Over tightening may strip bolts. Cover

all bolts with covers provided.

Step 5: Your chair is now ready for use. If you have any questions,

please call our Customer Service Center at 1-800-416-3511.

Figure 3

SEAT FRAME

IMPORTANT NOTE: Damage to welds or frames resulting from

over tightened bolts or improper assembly is not covered under

our warranty. Please read all instructions carefully before

assembly. If you have any questions regarding your assembly, call

our Customer Service Center at 1-800-416-3511.

HW0038

FC0234

FOOT CAP-1

FACTORY ASSEMBLY

LEFT ARM

Figure 2

FOOT CAP-2

FOOT CAP-1

1/4" X 30 MM BOLT

FC0654

FOOT CAP-2

FACTORY ASSEMBLY

Step 3: Repeat above process (Fig.1-Fig.3)for the right arm as shown

in F 4.igure

Figure 4

SZ1512

REST COVER

FACTORY ASSEMBLY

SUPPORT BAR-1

SUPPORT BAR-2

Summary of content (2 pages)

PAGE 1
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!! TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT Step 1: Identify parts packed in carton against the parts list. Remove all protective materials and set parts on a flat, non-abrasive surface. If you are missing any parts or are unsure how to proceed with assembly, call our Customer Service Center at 1-800-416-3511. Do not attempt to assemble table if any parts are missing or damaged.
PAGE 2
CARE AND MAINTENANCE FRAMES Cleaning - Use mild soap and warm water. Do not use abrasive materials, cleansers or bleach products. Rinse with clean water and dry thoroughly. Maintenance - Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to remove all water. This is critical.