Assembly Instructions & User’s Manual Model No: WELLFP5010 FOR OUTDOOR USE ONLY. KEEP THE INSTRUCTIONS FOR FUTURE REFERENCE. For product warranty,please go to www.hamptonbay.
Table of Contents Warnings ………….……………………………………………….2-5 Hardware and Tools............…………………..……………………6 Parts .........................................................................................7 Assembly Instructions …….………………………………………8-10 Installing Instructions.....……………………………………….......11-12 Operating Instructions ……………………………......................13 Lighting......................................................................................14 Cleaning and Care …………………………………....................
Warnings WARNING FOR YOUR SAFETY: Read these instructions before using this appliance. The appliance must be installed in accordance with the instructions and local regulations. The use of this appliance in enclosed areas can be dangerous and is PROHIBITED. Do the leak test after each changing of cylinder. Never check for leaks with a match or open flame. Do not store or use gasonline or other flammable vapors and liquids in the vicinity of this appliance.
Warnings WARNING DANGER WARNING indicates an imminently hazardous situation which, if not avoided, could result in death or serious injury. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. DANGER CAUTION CAUTION indicates an imminently hazardous situation which, if not avoided, may result in minor or moderate personal injury or property damage.
Warnings DANGER Solid fuels shall not be burned in this appliance DANGER The maximum inlet gas supply pressure: Max . 250PSI . Min 5PSI DANGER “Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water.” DANGER CARBON MONOXIDE HAZARD For outdoor use only. Never use inside house or other unventilated or enclosed areas.
Warnings You must provide propane gas and propane cylinder. Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the Standard for Storage and Handling of Liquified Petroleum Gas, ANSI/NFPA 58. Your local library or fire department should have this book. The minimum permissible gas supply pressure of 10 W.C. is required for purpose of input adjustment.
Hardware a Screw M6X12 20 pcs b Screw M6X25 6 pcs c Door handle 1 set d Wing nut 1 set PREPARATION --Select an area where you will assemble this product. To protect components, choose a smooth non abrasive surface that's free of cracks or openings. --Spread out all parts. --Tighten all hardware connections by hand first. Before completing each step, go back and fully tighten all hardware. Be careful not to over- tighten, that could damage surface or strip threads.
Parts List S/N Description Quantity S/N Description Quantity 1 Lava Rock 1 10 Leg with Tab 1 2 Hearth* 1 11 Side Panel 1 3 Bottom Bowl* 1 12 Door 1 4 B urner* 1 13 Leg with Magnet 1 5 Igniter Housing* 1 14 Door Handle 1 6 Control knob 1 15 Foot pad * 4 7 Regulator/Hose Assembly* 1 16 Base 1 8 Side Panel 2 17 Lid 1 9 Leg 2 * Pre-assembled 17 1 3 4 2 5 6 7 8 11 12 10 9 13 15 16 7 14
Assembly Step 1: door handle 10 12 Remove the screws and washer from the door handle ( c ). Attach the door handle ( c ) to door ( 12 ), then tighten the handle. Attach door (12) to leg (10) using M6X25 (b) - 2PC Note: Do not tighten all screws as you will need adjust the holes to ensure proper alignment. Step 2: 9 10 9 13 Remove control knob (6), attach legs (9), leg (10) and leg (13) with M6X12 (a) - 8 pcs. Be mindful of the direction of the door (12).
Assembly Instructions Step 3: 8 8 11 Attach side panels (8) and side panel ( 11) with M6X12 (a) -12 pcs. Step 4: 16 Note :the base's direction Note :the base's direction b 16 6 Attach the wing nut ( d ) to base (16). Attach base (16) by rotating to vertical position and lowering it into the center of the side panels. Rotate base (16) to horizontal position and attach with M6x25 (b) screws – 4pc. Attach the control knob (6). Please be mindful of the direction of the knob ( 6 ) when you install it.
Assembly Instructions Step 5: Turn unit upright. Place lava rocks. CAUTION: Do Not dump lava rocks out of package. Carefully place lava rocks by hand so that dust will not clog burner. CAUTION: Do Not cover pilot hosing.
Installing LP Gas Tank To operate, you will need one precision-filled standard LP grill gas tank with external valve threads.. CAUTION: LP gas tank must be properly disconnected and removed prior to moving this outdoor fireplace. Inserting and securing LP gas tank WARNING: Make sure LP gas tank valve is closed. Move the wing nut as below diagrammatic sketch Place precision-filled LP gas tank into ring hole in outdoor fireplace body so the tank valve is facing the gas line connection.
Installing LP Gas Tank Connection LP gas tank 1. Before connecting, be sure there is no debris caught in the head of the LP gas tank, head of the regulator valve or in the head of the burner or burner ports. 2. Connect regulator/hose assembly to tank by turning knob clockwise until it stops. Disconnecting LP gas tank 1. Before disconnecting, make sure the LP gas tank valve is OFF. 2. Disconnecting regulator/hose assembly from LP gas tank by turning knob counterclockwise until it is loose.
Operating Instructions Checking for leaks *WARNING: Before using this outdoor fireplace, make sure you have read , understand and are following all information provided in the “Warnings” section. Failure to follow those instructions can cause death, serious injury or property damage. Burner connections 1. Make sure the regulator hose and valve connections are securely fastened to the burner and the tank. 2. Visually check the connection between the burner/venture tube and orifice. 3.
Lighting CAUTION:Keep outdoor gas appliance area clear and free from combustible material, gasoline and other flammable vapors and liquid. CAUTION:Do NOT obstruct the flow of combustion and ventilation air. CAUTION:Check and clean burner/ venturi tubes for insects and insect nests. A clogged tube can lead to a fire. CAUTION:Attempting to light the burner with a lid on it may cause an explosion 1. Make sure all labels, packing and protective films have been removed from the outdoor fireplace. 2.
Cleaning and Care CAUTION: 1. All cleaning and maintenance should be done when outdoor fireplace is cool and with the fuel supply disconnected. 2. Do Not clean any outdoor fireplace part in a self-cleaning oven. The extreme heat will damage the finish. 3. Do Not enlarge valve orifices or burner ports when cleaning the valves or burners. Notices 1. This outdoor fireplace should be thoroughly cleaned and inspected on a regular basis. 2. Abrasive cleaners will damage this product. 3.
Cleaning and Care Cleaning surface 1. Wipe surface clean with mild dishwashing detergent or baking soda mixed with water. 2. For stubborn stains, use a citrus-based cleaner and nylon scrubbing brush. 3. Rinse clean with water. 4. Allow to air dry. Before Storing 1. Turn LP gas tank valve “OFF” . 2. Turn control knob to the “OFF” position. 3. Disconnect LP gas tank per” Disconnecting LP gas tank” section. 4. Clean all surface. 5. Lightly coat the burner with cooking oil to prevent excess rusting. 6.
TROUBLESHOOTING: Problem Burner will not light with match/lighter Possible Cause Prevention/Cure LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank per " Installing LP Gas Tank" section, then turn LP gas tank valve to "ON" No gas flow Check if LP gas tank is empty. A.If empty exchange, refill or replace B.
TROUBLESHOOTING: Problem Possible Cause Prevention/Cure New burner may have residual manufacturing oils Flame is yellow or orange Flame goes out Flashback (fire in burner/ venture tube(s) Flame seems to lose heat when burning in cold weather temperature Burn outdoor fire pit for 15 minutes and inspect.
CARE AND MAINTAINCE Service: Repair gas passages and associated components should be done only by a qualified service person. Caution: Always allow heater to cool before attempting service.