928 893 Carrolton 52 in Ceiling Fan Owner’s Manual Carrolton Ventilador de Techo de 1,32 m Manual del Propietario
Carrolton by Hampton Bay ®
52” Carrolton Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 UL Model No. 928-893 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Installing the Light Kit. . . . . . . . . . . . .10 Serial No. Operating Your Fan . . . . . . . . . . . . .
Safety Rules – Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the 2.
Unpacking Your Fan 2 1 Unpack your fan and check the contents. You should have the following items: 5 8 A B C D 3 6 4 9 7 1. 2. 3. 4. 5. Set of blades (5) Canopy assembly Ball/downrod assembly Fan motor assembly Blade arms (5) WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. 2 6, 7. 8. 9. Light kit Glass shades (3) 13 Watt compact fluorescent bulbs (3) Pull chain and fobs (2) A. Blade Attachment Hardware (16 Screws with Fiber Washers) B.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Mounting Options Ceiling Mounting Plate Figure 3 Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Figure 5) 2. Remove the mounting bracket from the canopy by removing the 1 of 2 screws from the bottom of the mounting bracket and loosening the other one a half turn from the screw head. Next, turn the canopy counter clockwise to removing the canopy cover form the canopy. (Figure 5) 3.
Installing Fan to the Electrical Box WARNING UL Listed Outlet Box THE TAB IN THE RING MUST REST IN THE GROOVE OF THE HANGER BALL AS FIGURE 7. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. 1.
If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire nuts supplied with your fan. Secure the wire nuts with electrical tape. Make sure there are no loose strands or connections. 1. Connect the ground conductor of the 120V supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan (Figure 9). 2.
Finishing the Fan Installation Outlet Box 1. Tuck connections neatly into ceiling outlet box. Ceiling Mounting Bracket 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 10) 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
Attaching the Fan Blades CAUTION Motor MOTOR IS SHIPPED WITH RUBBER MOTOR STOPS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE MOTOR STOPS PRIOR TO ATTACHING BLADE BRACKETS. (FIG. 11) 1. Attach blades to blade arm using the screws with fiber washers provided (Fig. 12). Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight. Repeat steps for the remaining blades. 3.
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 14.
Installing the Light kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE. 1. While holding the light kit under your fan, locate two single white and blue wires in the switch housing labeled "FOR LIGHT".
Operating Your Fan WARNING LOCKING SLOTS OF CEILING CANOPY ARE PRVIDED ONLY AS AN AID TO MOUNTING. DO NOT LEAVE FAN ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED. Warm weather - (Counter Clockwise Direction) A downward air flow creates a cooling effect as shown in Figure 17. This allows you to set your air conditioner on a higher setting without affecting your comfort. NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. Fan sounds noisy 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.
Specifications FAN SIZE SPEED VOLTS LOW 52” MED. HIGH 120 AMPS WATTS RPM CFM 0.26 15 75 1941 0.35 30 113 3089 0.51 63 170 4796 N.W. G.W. C.F. 7.7 kgs (16.94 lbs) 8.5 kgs (18.70 lbs) 1.63’ These are approximate measures. They do not include Amps and Wattage used by the light kit .
Hampton Bay Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
