22 135 Hawkins 44 in Ceiling Fan Owner’s Manual Hawkins Ventilador de Techo de 1,12 m Manual del Propietario
44” Hawkins Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 UL Model No. 122-135 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Installing the Light Kit. . . . . . . . . . . . . 8 Serial No. Operating Your Fan . . . . . . . . . . . . . .
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the 2.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: 2 5 3 8 A B C D 6 1 9 4 7 1. Set of blades (5) 6. Light kit 2. Mounting bracket 7. Glass shade 3. Fan motor assembly 8. Pull chains and fobs (2) 4. Motor housing 9. 40 Watt candelabra bulbs (3) 5. Blade arms (5) 10. Extra switch housing cover WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-898-1881. 2 10 A.
Installing Your Fan Tools Required Figures 1 and 2 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters. Outlet Box Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Figure 3 Figure 1 Secure the outlet box directly to the building structure.
Hanging the Fan 1. Connect the ground cnductor of the 120V supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan (Figure 6). REMEMBER to turn off the power. Follow the steps below to hang your fan properly. 1. Attach the mounting bracket to the outlet box with two screws and washers provided with the outlet box. Make sure the bracket is tight and secured (Fig. 4). 2.
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. BLACK WHITE Studs 1. Move fan into position over the four mounting studs and secure with the provided washers and nuts (Fig. 7). SUPPLY CIRCUIT Ground Conductor Outlet Box BLUE BLACK WHITE GREEN Finishing the Fan Installation 2.
Attaching the Fan Blades Screws with Fiber Washers Step 1. Attach blades to blade arms using three screws with fiber washers. (Fig. 9) Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. Motor Tab Slot Blade Assembly Step 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight. Repeat steps for the remaining blades. Blade Arm Step 3.
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Check that all blade and blade arm screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 11.
Installing the Light Kit NOTE NOTE NOTE BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. 1. While holding the light kit assembly under your fan, locate two single white and blue wires in the switch housing labeled FOR LIGHT. Make the polarized plug connections: - White to white - Blue to black 2. Carefully push all wires back into the switch housing.
Operating Your Fan NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION. Turn on the power and check the operation of the fan. The pull chain controls the fan speed as follows: Warm weather - (Counter Clockwise Direction) A downward air flow creates a cooling effect as shown in Figure 14. This allows you to set your air conditioner on a higher setting without affecting your comfort. 1 pull - High 2 pulls - Medium 3 pulls - Low 4 pulls - Off.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. Fan sounds noisy 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 44” MED. HIGH 120 WATTS RPM CFM 0.19 13 76 1540 0.31 28 123 2809 0.43 51 170 4286 N.W. G.W. C.F. 7.4 kgs (16.2 Ibs) 8.3 kgs (18.3 Ibs) 1.70’ These are approximate measures. They do not include Amps and Wattage used by the light kit .
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.