IMAGETEAM™ 2020/5620 Cordless System ™ System Manual
Disclaimer Hand Held Products, Inc. (“Hand Held Products“) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Hand Held Products to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Hand Held Products.
Statement of Agency Compliance The IT2020/IT5620 system meets or exceeds the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your IT2020/IT5620 system.
If necessary, the user should consult the dealer or an experienced radio/ television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Hand Held Products, Inc.
Hand Held Products shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
UL and cUL Statement UL listed UL1950 and CSA 22.2 No.950. cUL listed UL1950 and CSA 22.2 No 950. TÜV Statement TÜV or GS marked to EN60950 and EN60825-1. C-Tick Statement Conforms to AS/NZS 3548. C-Tick number: N10410. Mexico Certified Patents Please refer to the IT5620 packaging for patent information. Solids and Water Protection The IT5620 has a rating of IP41, immunity of foreign particles and dripping water.
Required Safety Labels IT5620
)&& ,' +' 0; % &DQDGD ,& %0; % 86 DQG )RUHLJQ 3DWHQWV 3HQGLQJ 0DGH LQ &KLQD , 7 ( $&&(6625< ' ( WWW HANDHELD COM +DQG +HOG 3URGXFWV ,QF 6NDQHDWHOHV )DOOV 1< IT2020 g g
Table of Contents Chapter 1 - Getting Started About This Manual ............................................................... 1-1 Unpacking the System .......................................................... 1-2 Models .................................................................................. 1-2 Cordless System: Main Components.................................... 1-3 About the Battery.................................................................. 1-3 Proper Disposal of the Battery ..........
Basic Operation of the Cordless System............................. 1-16 System Conditions........................................................ 1-17 Communication Between the Cordless System and the Host .................................................................. 1-18 Connecting the Base When Powered by Host (Keyboard Wedge) ........................................................... 1-18 Reading Techniques ............................................................
Wand Emulation..................................................................2-13 Wand Emulation Connection........................................2-13 Wand Emulation Transmission Rate ............................2-14 Wand Emulation Polarity..............................................2-14 Wand Emulation Idle ....................................................2-15 Wand Emulation Data Block Size ................................2-15 Wand Emulation Delay Between Blocks......................
Chapter 4 - Data Editing Prefix/Suffix Overview ......................................................... 4-1 To Add a Prefix or Suffix: ............................................. 4-2 To Clear One or All Prefixes or Suffixes: ...................... 4-3 To Add a Carriage Return Suffix to all Symbologies .... 4-3 Prefix Selections ............................................................. 4-3 Suffix Selections............................................................. 4-4 Function Code Transmit ......
Code 39..................................................................................6-5 Code 39 Start/Stop Characters .......................................6-5 Code 39 Check Character ...............................................6-6 Code 39 Message Length................................................6-6 Code 39 Append .............................................................6-7 Code 32 Pharmaceutical (PARAF).................................6-7 Full ASCII........................................
UPC E0 and UPC E1........................................................... 6-21 UPC E0 and UPC E1 Expand....................................... 6-21 UPC E0 and UPC E1 Addenda Required..................... 6-21 UPC E0 and UPC E1 Addenda Separator .................... 6-22 UPC E0 Check Digit..................................................... 6-22 UPC E0 Number System .............................................. 6-22 UPC E0 Addenda..........................................................
Code 49................................................................................6-36 Code 49 Message Length..............................................6-36 Chapter 7 - Interface Keys Keyboard Function Relationships .........................................7-1 Supported Interface Keys ......................................................7-3 Chapter 8 - Utilities To Add a Test Code I.D. Prefix to All Symbologies ............8-1 Reset Scanner ........................................................
Resetting the Standard Product Default Settings: All Application Work Groups ................................................ 10-5 Menu Commands ................................................................ 10-6 Chapter 11 - Product Specifications IMAGETEAM 5620 Product Specifications ...................... 11-1 IMAGETEAM 2020 Product Specifications ...................... 11-2 IMAGETEAM 5620 Depth of Field ................................... 11-3 Chapter 12 - Maintenance Maintenance ...................
1 Getting Started The IMAGETEAM 5620 cordless scanning system consists of one IT2020-5A base and one IT5620 Cordless Linear Imager. Up to seven scanners may be linked to one base. The IT5620 marks a new performance level for hand held scanners. The IT5620 is powered by Hand Held Products AdaptusTM Imaging Technology. The performance of Adaptus technology delivers aggressive read rates and depths of field on 1D codes.
• Connection of the Base to an Interface Unpacking the System After you open the shipping carton containing the product, take the following steps: • Check to make sure everything you ordered is present. • Save the shipping container for later storage or shipping. • Check for damage during shipment. Report damage immediately to the carrier who delivered the carton.
Cordless System: Main Components Battery Contained in Handle About the Battery ! Use only the Li-ion battery packs provided by Hand Held Products. The use of any battery pack not sold by Hand Held Products will void your warranty and may result in damage to your unit. Power is supplied to the cordless scanner by a rechargeable battery that is integrated in the scanner handle. Each scanner is shipped with a battery. (See Product Specifications beginning on page 11-1.
Battery Recommendations • Batteries are shipped approximately 30% to 60% charged and should be fully charged for maximum charge capacity. • The battery is a lithium ion cell and can be used without a full charge, as well as can be charged without fully discharging, without impacting the battery life. There is no need to perform any charge/discharge conditioning on this cell type battery. • Do not disassemble the battery. There are no user-serviceable parts in the battery.
Base Charge Mode In order for the battery to be charged, there must be enough voltage for the circuitry to work. There are three conditions during which power can be supplied to the base: Condition 1: Condition 2: Condition 3: 9VDC power supply connected to the barrel connector 12VDC host power source only 5VDC host power source only The chart below describes each selection by condition.
Linking Scanner to Base When newly shipped or defaulted to factory settings, the base and scanner are not linked. Once the scanner is placed into the base, the software automatically links the scanner and the base. If the scanner and base have previously been linked, you do not receive any feedback. If this is the first time that the scanner and base are linked, both devices emit a short chirp when their radios link. At this point, you are set to one imager to one base.
Single Scanner Operation There are two link modes to accommodate different applications: Locked Link Mode and Open Link Mode. Scan the appropriate bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default = Locked Link Mode. Locked Link Mode - Single Scanner If you link an scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base.
Multiple Scanner Operation To put the scanner in multiple scanner mode, scan the bar code below. Once you scan this bar code, the scanner is unlinked from the base and must be placed into the base to re-link. Multiple Scanner Operation Note: Multiple Scanner Operation Mode allows you to link up to 7 scanners to one base. You cannot join an eighth scanner until you unlink one of the 7 scanners or take an scanner out of range. Scanner Name You are able to assign a name to each scanner you are using.
Changing Scanner Name - via Bar Codes If you wanted set up your scanners with names 0001-0007, you may scan the bar codes below. Scan the Reset bar code after each name change and wait for the scanner to re-link to the base before scanning the next bar code to name the next scanner. 0001 0002 0003 0004 0005 0006 0007 Reset Alternatively, you may change the name with a bar code command if you cannot send serial commands to the base.
Scanner Report Scan the bar code below to generate a report for the connected scanners. The report indicates the port, work group, scanner name, and address. Scanner Report Application Work Groups Your cordless system can have up to seven scanners linked to one base. You can also have up to seven work groups. If you want to have all of the scanners’ settings programmed alike, you don’t need to use more than one work group. If you want each scanner to have unique settings (e.g.
Application Work Group Selection This programming selection allows you to assign an scanner to a work group by scanning the bar code below. You may then program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires.
Resetting the Standard Product Default Settings: Current Application Work Group If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want the standard product default settings restored, scan the Standard Product Default Settings: Current Application Group bar code below. The Menu Commands starting on page 10-6 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
Using the Scanner with Bluetooth Devices The IT5620 scanner may be used either with the IT2020-5A base or with other Bluetooth devices. Scanning the Non-Base Bluetooth Connection bar code below allows the scanner to be used with other Bluetooth devices (e.g., PDA, PC - Bluetooth USB Adapter). After you scan the bar code below, follow the instructions supplied with your Bluetooth device to locate the scanner and connect to it.
Note: If you are out of range when you scan a bar code, you will receive an error beep even if you do not have the alarm set. You receive the error beep since the data could not be communicated to the base or the host. Alarm Sound Type If you have set the out-of-range alarm enabled, you may change the alarm type for the scanner or base by scanning the appropriate bar code below and then scanning a digit (0-7) bar code and the Save bar code on the Programming Chart inside the back cover of this manual.
IT5620 LED Sequences and Their Meaning LED Indication Beeper Indication Cause Normal Operation Red Flash None Green Flash 1 beep Red, blinking Menu Operation Green Flash Red, blinking 3 beeps Battery low Successful communication or linking Failed communication 2 beeps 3 beeps Successful menu change Unsuccessful menu change IT2020 LED Sequences and Their Meaning The base contains a red LED that indicates the status of the unit and verifies its communication with the host system and a green LED th
Note: Charging only occurs with external power applied to the IT2020 or 12 volt Host power. Charge Condition Charge Status Indicator (Green LED) Scanner inserted into base Three flashes >80% charged On continuously 30% to 80% charged Slow flash, 1 second on, 1 second off <30% charged Fast flash, 300 mSec on, 300 mSec off Basic Operation of the Cordless System Cordless Base The cordless base provides the link between the cordless scanner and the host system.
Cordless Scanner The cordless scanner enables fast and accurate bar code scanning using a noncontact linear scanner. The scanner is comprised of a linear scanner, a decode/control assembly, and an RF communication module. The scan engine performs the bar code image illumination and sensing.
Communication Between the Cordless System and the Host The cordless scanner provides immediate feedback in the form of a “good read” indication (a green LED on the scanner and an audible beep) after a bar code is scanned correctly and the base has acknowledged receiving the data. This is possible since the cordless system provides two-way communication between the scanner and the base. When data is scanned, the data is sent to the host system via the base unit.
2. Disconnect the keyboard cable from the back of the terminal/ computer. Disconnect 3. Connect the appropriate interface cable to the base and to the terminal/ computer and keyboard. 4. Turn the terminal/ computer power back on. 3 1 2 5. Program the base for the keyboard wedge interface. See "Keyboard Wedge Connection" on page 121.) 6. Verify the base operation by scanning a bar code from the Sample Symbols in the back of this manual.
Reading Techniques The scanner has a view finder that projects a bright red aiming beam that corresponds to its horizontal field of view. The aiming line should be centered horizontally over the bar code; it will not read if the aiming line is in any other direction. Good Read Bad Read Bad Read The best focus point for reading most code densities is about 5 inches (12.7 cm) from the unit.
Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge Connection If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below. Keyboard wedge is the default interface. Note: The following bar code also programs a carriage return (CR) suffix.
Wand Emulation Plug & Play In Wand Emulation mode, the scanner decodes the bar code then sends data in the same format as a wand scanner. The Code 39 Format converts all symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code 128 and Interleaved 2 of 5 without any changes, but converts all other symbologies to Code 39. The Wand Emulation Plug & Play Code 39 Format bar code below sets the terminal ID to 61. The Wand Emulation Plug & Play Same Code Format bar code sets the terminal ID to 64.
IBM 4683 Ports 5B, 9B, and 17 Interface Scan one of the following “Plug and Play” codes to program the IT5620 for IBM 4683 Port 5B, 9B, or 17. Note: After scanning one of these codes, you must power cycle the cash register.
Connecting the Base with USB A base can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the base and to the computer. 2. Program the base for the USB interface by scanning the appropriate programming bar code. 3. Verify the base operation by scanning a bar code from the Sample Symbols in the back of this manual. For additional USB programming and technical information, refer to Hand Held Products “USB Application Note,” available at www.handheld.com.
IBM SurePos Scan one of the following “Plug and Play” codes to program the IT5620 for IBM SurePos (USB Hand Held scanner) or IBM SurePos (USB Tabletop scanner). Note: After scanning one of these codes, you must power cycle the cash register.
USB HID Scan the following code to program the IT5620 for USB HID bar code scanners. Scanning this code changes the terminal ID to 131. USB HID Bar Code Scanner USB Com Port Emulation Scan the following code to program the IT5620 to emulate a regular RS-232based Com Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Hand Held Products website (www.handheld.com). The driver will use the next available Com Port number.
Connecting the Base with Serial Wedge The IT2020 uses TTL signal levels to wedge into an RS-232 serial network. Use only IT2020-5A serial wedge cables to prevent damage to the base. Refer to Connecting the Base with RS-232 Serial Port on page 2-7 to set the baud rate and communications protocol. 1. Turn off power to the computer. 2. Disconnect the existing serial cable from the computer. 3. Connect the appropriate interface cable to the base.
To set up the serial wedge terminal ID, use the serial terminal ID 050 and follow the instructions on page 2-1. Make sure that all of the communication parameters match on all of the connected devices. Choosing Both sends scanned data to P1 and P2. Default = P1.
2 Terminal Interfaces Terminal ID If your interface is not a standard PC AT, refer to "Supported Terminals" on page 2-2 through page 2-3, and locate the Terminal ID number for your PC. Scan the Terminal ID bar code below, then scan the numeric bar code(s) from the Programming Chart inside the back cover of this manual to program the scanner for your terminal ID. Scan Save to save your selection. For example, an IBM AT terminal has a Terminal ID of 003.
Supported Terminals Terminal DEC DEC Esprit Heath Zenith HP IBM IBM IBM IBM 102 key IBM 122 key IBM 122 key IBM 122 key IBM 122 key IBM DOS/V 106 key IBM SurePOS IBM SurePOS IBM Thinkpad IBM Thinkpad IBM Thinkpad I/O 122 key ITT Lee Data NEC Olivetti Olivetti RS-232 TTL Serial Wedge Silicon Graphics Telex 88 key Telex 88 key Telex 102 key 2-2 Model(s) VT510, 520, 525 (PC style) VT510, 520, 525 (DEC style LK411) 200, 400 PC, AT Vectra XT PS/2 25, 30, 77DX2 AT, PS/2 30–286, 50, 55SX, 60, 70, 70–061, 70–121,
Supported Terminals (Continued) Terminal Telex 122 key Model(s) 078, 078A, 79, 80, 191, 196, 1191,1192, 1471, 1472, 1476, 1477, 1482, 1483 USB PC Keyboard USB Mac Keyboard USB Com Port USB HIDPOS Wand Emulation (Code 39 Format) Wand Emulation (Same Code Format) Terminal ID 046 124** 125** 130 131** 061 064 * Default for IT2020-5A. **It is best to use the Plug and Play bar codes, beginning on page 1-25 to program these interfaces, rather than scanning the terminal ID listed in this table.
Keyboard Country Scan the appropriate country code below to program the keyboard for your country.
Please refer to the Hand Held Products website (www.handheld.com) for complete keyboard country support information and applicable interfaces. If you need to program a keyboard for a country other than one listed above, scan the Program Keyboard Country bar code below, then scan the numeric bar code(s) for the appropriate country from the inside back cover, then the Save bar code. Program Keyboard Country Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. Default = Regular.
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Emulate External Keyboard Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + ASCII Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F.
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off Automatic Direct Connect Mode On * Automatic Direct Connect Mode Off Connecting the Base with RS-232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the base. Note: For the base to work properly, you must have the correct cable for your type of terminal/computer. 3 4 2 5 3.
All communication parameters between the scanner and terminal must match for correct data transfer through the serial port using RS-232 protocol. Scanning the RS-232 interface bar code, programs the scanner for an RS-232 interface at 115,200 baud, parity–none, 8 data bits, 1 stop bit, and adds a suffix of a CR LF. RS-232 Interface RS-232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner.
RS-232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications which require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity. Default = None.
RS-232 Handshaking RS-232 Handshaking allows control of data transmission from the Imager using software commands from the host device. CTS/RTS operates in mode 2. When this feature is turned Off, no data flow control is used. When Data Flow Control is turned On, the host device suspends transmission by sending the XOFF character (DC3, hex 13) to the Imager. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent.
The commands to which the scanner responds are listed on page 2-12. The is a 1B in hex. A typical command string is y x, where “y” is the application work group number, “ x” is the escape command, and the comma is the terminator. Commands may be strung together to create custom response sequences. An example of a command string is listed below. 0456, The above example will make a scanner in application work group zero beep low, medium, high.
IT2020-5 Host Escape Commands Command Action a Indicate as if successful menu change made b Indicate as if unsuccessful menu change made 1 Illuminate green LED for 135 milliseconds (followed by at least 70 mSecs. dark time when multiple blinks) 2 Illuminate green LED for two seconds (followed by at least 500 mSecs. dark time when multiple blinks) 3 Illuminate green LED for five seconds (followed by at least 500 mSecs.
Wand Emulation Wand Emulation Connection The Wand Emulation Connection bar codes should be used if you want to change the terminal ID only, without changing any other imager settings. We recommend using Wand Emulation Plug & Play bar codes to program your imager to emulate a wand reader. The Wand Emulation Plug & Play bar codes change other parameters, in addition to changing the terminal ID. Please refer to Wand Emulation Plug & Play on page 1-22 for further information.
Wand Emulation Transmission Rate The transmission rate is limited by the terminal’s ability to receive data without dropping characters. Default = 25 inches/second. 10 * 25 40 80 120 150 200 Wand Emulation Polarity The Polarity can be sent as standard with black bars high, or reversed with white bars high. Default = Black High.
Wand Emulation Idle The idle describes the state of the scanner when no data is being transmitted. When in Wand Emulation mode, you must set the scanner’s idle state to match the idle state for the device to which the scanner is connected. Default = Idle High. * Idle High Idle Low Wand Emulation Data Block Size This transmits the data in smaller blocks to prevent buffer overflow. Default = 40. 20 * 40 60 80 Wand Emulation Delay Between Blocks This sets the delay time between data blocks. Default = 50ms.
Wand Emulation Overall Checksum When this option is turned on, a computed check character is added at the end of the entire message. The check character is the character which when Exclusive-OR’d with every preceding character of the message yields a result of 0x00 (00H). Default = Off.
3 Output Scanner Functions Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = On. * Beeper - Good Read On Beeper - Good Read Off Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = Medium.
Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (3250 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another.
Scanner Trigger Modes Manual/Serial Trigger, Low Power You can activate the scanner either by pressing the trigger, or using a serial trigger command (see "Trigger Commands" on page 10-4). When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released. When in serial mode, the scanner scans until a bar code has been read or until the deactivate command is sent.
Note: Scanning zero (0) is the equivalent of setting no time-out. If there are no trigger pulls during the “scanner power time-out timer” interval, the scanner goes into power down mode. Whenever the trigger is enabled, the “scanner power time-out timer” is reset. If the scanner is placed in the IT20205A cradle and the battery is in the process of being charged, the scanner will not go into power down mode.
Hands Free Time-Out The Automatic Trigger and Presentation Modes are referred to as “hands free” modes. If the imager’s trigger is pulled when using a hands free mode, the imager changes to manual trigger mode. You can set the time the imager should remain in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the imager reverts to the original hands free mode.
Centering Window Use the centering feature to narrow the scanner’s field of view so the scanner reads only the bar code you want. When centering is turned on, the scanner only reads codes that intersect or are contained within the centering window you set up. At least part of a bar code must be within the window to be decoded or output by the scanner. To change the left or right edge of the centering window, scan Centering On, then scan one of the following bar codes.
Example: If you have two bar codes next to one another and the centering window is set to 40% left edge and 60% right edge, only the bar code that intersects that window will be decoded. Decoded bar code 40% 30% 60% 70% 80% 20% 90% 10% 0% 100% Output Sequence Overview Require Output Sequence When turned off, the bar code data will be output to the host as the scanner decodes it.
3. Length Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted characters as part of the length (unless using 9999). 4.
Note: This selection is unavailable when the Multiple Symbols Selection is turned on. Required On/Not Required * Off Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example.
41 start character match for Code 39, 41h = “A” FF termination string for first code 6A code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths 42 start character match for Code 128, 42h = “B” FF termination string for second code 69 code identifier for Code 93 9999 code length that must match for Code 93, 9999 = all lengths 43 start character match for Code 93, 43h = “C” FF termination string for third code To program the previous example using specific lengths, you w
Multiple Symbols When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner’s trigger. If you press and hold the trigger, aiming the scanner at a series of symbols, it reads unique symbols once, beeping (if turned on) for each read. The scanner attempts to find and decode new symbols as long as the trigger is pulled. When this programming selection is turned Off, the scanner will only read the symbol closest to the aiming beam.
4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data.
To Add a Prefix or Suffix: Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-3). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Appendix A) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4.
To Clear One or All Prefixes or Suffixes: You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. When you Clear One Prefix (Suffix), the specific character you select is deleted from the symbology you want. When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted. Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2.
Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 7-3. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual. Prefix Scanned Data 1 2 3 4 Suffix 5 Intercharacter Delay Intercharacter Delay To remove this delay, scan the Intercharacter Delay bar code, then set the number of steps to 0.
Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual. Prefix STX 1 Scanned Data HT 2 3 4 5 Suffix CR LF Interfunction Delays Interfunction Delay To remove this delay, scan the Interfunction Delay bar code, then set the number of steps to 0.
5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
Note: The wildcard for all terminal types is 099. Step 4. Code I.D. In the Appendix A, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual.
hex values for ASCII codes, see ASCII Conversion Chart (Code Page 1252) on page A-2.) F4 Send “xx” character “nn” times (Insert) leaving cursor in current cursor position. Syntax = F4xxnn (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-2, and nn is the numeric value (00-99) for the number of times it should be sent.) E9 Send all but the last “nn” characters, starting from the current cursor position.
E4 Replaces up to 15 characters in the data string with user specified characters. Replacement continues until the E5 command is encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total count of both characters to be replaced plus replacement characters; xx1 defines characters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. E5 Terminates character replacement. Syntax = E5. FE Compare character in current cursor position to the character “xx.
Data Formatter When Data Formatter is turned off, the bar code data is output to the host as read (including prefixes and suffixes). Choose one of the following options. Default = Data Formatter On. * Data Formatter On, but Not Required Data Formatter Off When Data Formatter is required, all input data must conform to an edited format or the scanner does not transmit the input data to the host device.
5-6 IMAGETEAM™ 2020/5620 System Manual
6 Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults.
Message Length You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code doesn’t match the valid reading length, the scanner will issue an error beep. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread. EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09 Max.
Codabar Codabar * On Off Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16 check characters. Default = No Check Character.
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character.
Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length Code 39 < Default All Code 39 Settings > Code 39 * On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters.
Code 39, continued Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data.
Code 39, continued Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 39 bar codes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the order in which the bar codes are read, deleting the first space from each.
Note: Trioptic Code must be turned off to scan Code 32 Pharmaceutical codes. On * Off Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = On.
Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
Code 93 < Default All Code 93 Settings > Code 93 * On Off Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Code Page Code pages define the mapping of character codes to characters.
Code 2 of 5 Code 2 of 5 On * Off Code 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
IATA Code 2 of 5, continued On * Off IATA Code 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11 Code 11 On * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
Code 11, continued Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Code 128, continued ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license.
Code 128 Function Code Transmit By default, Code 128 function codes are not transmitted with Code 128 bar code data. However, if you wish to transmit Code 128 function codes with the bar code data, scan the Function Codes On bar code, below. * Function Codes Off Function Codes On Telepen Telepen On * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1).
Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC A UPC A * On Off UPC A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
UPC A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data. Default = Off for both 2 Digit and 5 Digit Addenda.
UPC A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. Default = On.
UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1). * UPC E0 On UPC E0 Off UPC E1 On * UPC E1 Off UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off.
UPC E0 and UPC E1 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC E0 Number System The numeric system digit of a U.P.C.
UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 EAN/JAN 13 * On Off EAN/JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 Addenda Required When Addenda Required is set to on, the scanner will only read EAN/JAN 13 bar codes that have addenda. Default = Not Required.
Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code on page 6-20. ISBN Translate This selection causes EAN-13 Bookland symbols to be translated into their equivalent ISBN number format. Default = Off. On * Off EAN/JAN 8 EAN/JAN 8 * On Off EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 8 Addenda Required When Addenda Required is set to on, the scanner will only read EAN/JAN 8 bar codes that have addenda. Default = Not Required.
MSI MSI On * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate and Transmit, the scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data.
MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Plessey Code Plessey Code On * Off Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information.
RSS-14 < Default All RSS-14 Settings > RSS-14 * On Off RSS Limited < Default All RSS Limited Settings > RSS Limited * On Off IMAGETEAM™ 2020/5620 System Manual 6 - 29
RSS Expanded < Default All RSS Expanded Settings > RSS Expanded * On Off RSS Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
Identifier will be reported as “]C1”. If RSS Emulation is selected, the AIM Symbology Identifier will be reported as “]e0.” Any application that accepts EAN•UCC data can be simplified since it only needs to recognize one data carrier type. Default = EAN•UCC Emulation Off. RSS Emulation 128 Emulation * EAN•UCC Emulation Off China Post Code China Post Code On * Off China Post Message Length Scan the bar codes below to change the message length.
Korea Post Code Korea Post Code On * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
PosiCode A and B * On Off You have to have PosiCode A and B on to read any of the PosiCode symbologies. A and B On (No Limited) A and B and Limited A On (Limited B Off) * A and B and Limited B On (Limited A Off) PosiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Trioptic Code Trioptic Code is used for labeling magnetic storage media. Note: If you are going to scan Code 32 Pharmaceutical codes, Trioptic Code must be off. On * Off Codablock F Codablock F On * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Code 16K Code 16K On * Off Code 16K Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-160. Minimum Default = 1, Maximum Default = 160.
Code 49 * On Off Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81.
7 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-6 enable Control + ASCII mode.
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States [ \ ] 6 - Belgium [ < ] 6 - Scandinavia 8 < 9 6 - France ^ 8 $ 6 = Germany à + 6 - Italy \ + 6 - Switzerland < ..
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM AT/XT and PS/2 Compatibles, WYSE PC/AT Supported Keys Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Tab Reserved Tab Delete CR/Enter Insert Escape F11 Home Print Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM, Memorex Telex (102)* Supported Keys Reserved Enter F11 F12 F13 F14 F15 New Line F16 F17 F18 Tab/Field Forward Delete Field Exit Insert Clear Error Reset Home Print Back Space Back Tab F19 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Memorex Telex (88)** Supported Keys Res
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Esprit 200, 400 ANSI Supported Keys Reserved New Line N/A N/A N/A N/A N/A New Line N/A Tab N/A Tab N/A New Line N/A Escape F11 Insert F13 Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Esprit 200, 400 ASCII Supported Keys Reserved New Line N/A N/A N/A N/
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DEL 7-6 HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F Apple Mac/iMac Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make TAB APPLE break TAB Del RETURN Ins Help ESC F11 Home Prnt Scrn BACKSPACE LSHIFT TAB F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 BACKSPACE
8 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, included in the Appendix A, page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is reset.
Scanner Report Scan the bar code below to generate a report for the connected scanners. The report indicates the port, work group, scanner name, and address. To assign a name to your scanner, refer to "Menu Command Syntax" on page 10-1. Scanner Report Scanner Address Scan the bar code below to determine the address of the scanner you are using. Scanner Address Base Address Scan the bar code below to determine the address of the base you are using.
Note: Scanning this bar code also causes both the scanner and the base to perform a reset and become unlinked. Refer to "Scanner Modes" on page 1-6 for additional information. Standard Product Default Settings: Current Application Group Resetting the Standard Product Default Settings: All Application Work Groups The following bar code defaults all of the work groups to the factory settings.
8-4 IMAGETEAM™ 2020/5620 System Manual
9 Visual Menu 2003 Visual Menu 2003 Introduction Visual Menu 2003 provides the ability to configure a Hand Held Products scanning device by connecting the scanner to the com port of a PC. Visual Menu 2003 allows you to download updates to a scanner’s firmware, change programmed parameters, and create and print programming bar codes. Using Visual Menu 2003, you can even set up the configuration for a scanner which is not attached to your PC.
6. Double click on the Visual Menu 2003.exe file. Follow the screen prompts to install the Visual Menu 2003 program. 7. To start Visual Menu 2003, from the Start Menu click on Programs, Visual Menu 2003, Visual Menu 2003.
10 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the IT2020-5. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS-232 interface (see page 1-21). The following commands can be sent via a PC com port using terminal emulation software.
Data The new value for a menu setting, identified by the Tag and SubTag. Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent changes you want saved through a power cycle.
Concatenation of Multiple Commands Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are issued. If the additional command requires a different Tag field, the command is separated from previous commands by a semicolon (;).
Example #4: What are the device’s settings for all Codabar selections? Enter: cbr?. Response: CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK].
Resetting the Standard Product Default Settings: Current Application Work Group If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want the standard product default settings restored, scan the Standard Product Default Settings: Current Application Group bar code below. The Menu Commands starting on page 10-6 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
Menu Commands Selection Base Charge Mode Setting Serial Command Page * Indicates default # Indicates a numeric entry *Automatic BASCHG1 1-5 Full Charge Rate BASCHG2 1-5 Low Charge Rate BASCHG3 1-5 Battery Charge Off BASCHG4 1-5 Unlink Imager BT_RMV 1-6 *Locked Link Mode BASCON0,DN G1 1-7 Open Link Mode BASCON1,DN G1 1-7 Imager Modes - Single Override Locked Imager BT_RPL1 1-7 Multiple Imager Operation Multiple Imager Operation BASCON2,DN G3 1-8 Imager Name Imager Name
Selection Alarm Sound Type Data Accumulation Mode Factory Default Settings Setting Serial Command Page * Indicates default # Indicates a numeric entry Base Alarm Type BASORW 1-14 Scanner Alarm Type BT_ORW 1-14 On BATENA1 1-14 *Off BATENA0 1-14 Default DEFALT 1-20 *003 TERMID### Terminal Interfaces Terminal ID Program Keyboard Country Keyboard Style Keyboard Modifiers Serial Port Connection 2-2 *USA KBDCTY0 2-4 Belgium KBDCTY1 2-4 Denmark KBDCTY8 2-4 Finland KBDCTY2
Selection Baud Rate Word Length: Data Bits, Stop Bits, and Parity RS-232 Handshaking Wand Emulation Connection 10 - 8 Setting Serial Command Page * Indicates default # Indicates a numeric entry 300 BPS 232BAD0 2-8 600 BPS 232BAD1 2-8 1200 BPS 232BAD2 2-8 2400 BPS 232BAD3 2-8 4800 BPS 232BAD4 2-8 9600 BPS 232BAD5 2-8 19200 BPS 232BAD6 2-8 38400 BPS 232BAD7 2-8 57600 BPS 232BAD8 2-8 *115200 BPS 232BAD9 2-8 7 Data, 1 Stop, Parity Even 232WRD3 2-9 7 Data, 1 Stop, Pari
Selection Wand Emulation Transmission Rate Wand Emulation Polarity Wand Emulation Idle Wand Emulation Data Block Size Wand Emulation Delay Between Blocks Wand Emulation Overall Checksum Setting * Indicates default Serial Command # Indicates a numeric entry Page 10 WNDSPD0 2-14 *25 WNDSPD1 2-14 40 WNDSPD2 2-14 80 WNDSPD3 2-14 120 WNDSPD4 2-14 150 WNDSPD5 2-14 200 WNDSPD6 2-14 *Black High WNDPOL0 2-14 White High WNDPOL1 2-14 Idle Low WNDIDL0 2-15 *Idle High WNDIDL1 2-
Selection Beeper Duration - Good Read LED - Good Read Number of Beeps - Good Read Good Read Delay User-Specified Good Read Delay Trigger Mode Reread Delay User-Specified Reread Delay 10 - 10 Setting Serial Command Page * Indicates default # Indicates a numeric entry *Normal Beep BEPBIP0 Short Beep BEPBIP1 3-2 Off BEPLED0 3-2 3-2 *On BEPLED1 3-2 *1 BEPRPT1 3-3 Range 1 - 9 BEPRPT# 3-3 *No Delay DLYGRD0 3-3 Short Delay (500 ms) DLYGRD500 3-3 Medium Delay (1000 ms) DLYGRD10
Selection Centering Output Sequence Editor Require Output Sequence Multiple Symbols No Read Video Reverse Setting Serial Command Page * Indicates default # Indicates a numeric entry Centering On DECWIN1 3-7 *Centering Off DECWIN0 3-7 Left of Centering Window *40 DECLFT### 3-7 Right of Centering Window *60 DECRGT### 3-7 Enter Sequence SEQBLK 3-9 Default Sequence SEQDFT 3-9 Required SEQ_EN2 3-10 On/Not Required SEQ_EN1 3-10 *Off SEQ_EN0 3-10 On SHOTGN1 3-12 *Off SHOT
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Data Formatter Selections Data Format Editor Data Formatter Alternate Data Formats *Default Data Format (None) DFMDF3 5-4 Enter Data Format DFMBK3## 5-4 Clear One Data Format DFMCL3 5-4 Clear All Data Formats DFMCA3 5-4 Off DFM_EN0 5-5 *On, but Not Required DFM_EN1 5-5 On, Required DFM_EN2 5-5 1 VSAF_1 5-5 2 VSAF_2 5-5 3 VSAF_3 5-5 All Symbologies Off ALLENA0 6-1 All Symbologies On
Selection Code 39 Start/Stop Char. Code 39 Check Char. Code 39 Message Length Code 39 Append Code 32 Pharmaceutical (PARAF) Code 39 Full ASCII Interleaved 2 of 5 Interleaved 2 of 5 Interleaved 2 of 5 Check Digit Interleaved 2 of 5 Message Length Code 93 Code 93 Code 93 Message Length Code 2 of 5 Code 2 of 5 Setting * Indicates default Serial Command # Indicates a numeric entry Page *Don’t Transmit C39SSX0 6-5 Transmit C39SSX1 6-5 *No Check Char.
Selection Code 2 of 5 Message Length IATA Code 2 of 5 IATA Code 2 of 5 IATA Code 2 of 5 Message Length Matrix 2 of 5 Matrix 2 of 5 Matrix 2 of 5 Message Length Code 11 Code 11 Code 11 Check Digits Required Code 11 Message Length Code 128 Code 128 ISBT Concatenation Code 128 Message Length Setting Serial Command Page * Indicates default # Indicates a numeric entry Minimum (1 - 48) *4 R25MIN## 6-12 Maximum (1 - 48) *48 R25MAX## 6-12 Default All IATA Code 2 of 5 Settings A25DFT 6-13 6-13 *Off
Selection ISBT Concatenation Telepen Telepen Telepen Output Telepen Message Length UPC A UPC A UPC A Check Digit UPC A Number System UPC A 2 Digit Addenda UPC A 5 Digit Addenda UPC A Addenda Required UPC A Addenda Separator UPC E UPC E0 UPC E1 UPC E Expand Setting * Indicates default Serial Command # Indicates a numeric entry Page *Off ISBENA0 6-16 On ISBENA1 6-16 Default All Telepen Settings TELDFT 6-17 *Off TELENA0 6-17 On TELENA1 6-17 *AIM Telepen Output TELOLD0 6-17 Origi
Selection UPC E Check Digit UPC E Number System UPC E 2 Digit Addenda UPC E 5 Digit Addenda UPC E Addenda Required UPC E Addenda Separator EAN/JAN 13 Setting Serial Command Page * Indicates default # Indicates a numeric entry Off UPECKX0 *On UPECKX1 6-22 Off UPENSX0 6-22 *On UPENSX1 6-22 *Off UPEAD20 6-23 6-22 On UPEAD21 6-23 *Off UPEAD50 6-23 On UPEAD51 6-23 6-21 *Not Required UPEARQ0 Required UPEARQ1 6-21 Off UPEADS0 6-22 *On UPEADS1 6-22 Default All EAN/ JAN
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page EAN/JAN 8 2 Digit Addenda *Off EA8AD20 6-26 On EA8AD21 6-26 EAN/JAN 8 5 Digit Addenda *Off EA8AD50 6-26 On EA8AD51 6-26 EAN/JAN 8 Addenda Required *Not Required EA8ARQ0 6-26 Required EA8ARQ1 6-26 EAN/JAN 8 Addenda Separator Off EA8ADS0 6-26 *On EA8ADS1 6-26 Off CPNENA0 6-26 *On CPNENA1 6-20 Default All MSI Settings MSIDFT 6-27 *Off MSIENA0 6-27 Coupon Code MSI MSI MSI Check Char
Selection RSS Expanded RSS Expanded Msg. Length EAN•UCC Emulation China Post Code China Post Code China Post Code Msg.
Selection Codablock F Msg.
10 - 20 IMAGETEAM™ 2020/5620 System Manual
11 Product Specifications IMAGETEAM 5620 Product Specifications Parameter Specification Dimensions (Typical): Height 6.2 inches (15.7 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) Weight (with battery) 9.2 ounces (260 g) Light Source 630 nM visible red LED Scan Rate 270 scans per second in most usages Skew Angle ±65 degrees Pitch Angle ±65 degrees Horizontal Velocity 2 inches (5 cm) per second Scan Contrast 20% minimum Battery: Lithium Ion Battery Capacity: Storage: 3.
IMAGETEAM 2020 Product Specifications Parameter Specification Dimensions (Typical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.3 inches (10.9 cm) Weight 8.8 ounces (250 g) Voltage: DC Barrel 8.5 to 9.5 volts Host Port 4.
IMAGETEAM 5620 Depth of Field Minimum Bar Width Maximum Near Field Minimum Far Field (no ambient lighting) 13 mil 100% UPC 1 in (2.5 cm) 24 in (61 cm) 7.5 mil Code 39 4 in (10 cm) 14 in (36 cm) 10 mil Code 39 2 in (5 cm) 18 in (46 cm) 13 mil Code 39 1 in (2.5 cm) 24 in (61 cm) 15 mil Code 39 1 in (2.5 cm) 28 in (71 cm) 20 mil Code 39 1 in (2.5 cm) 36 in (91 cm) 55 mil Code 39 2.
11 - 4 10 2 3 4 5 6 7 8 9 1 connects to the base Cord shield Tied to supply power Supply ground Terminal clock Terminal data Supply power input (Refer to tables on page 11-2.
Standard Cable Pinouts Wand Emulation 10 Pin Modular Plug connects to the base 9 Pin Type D Female connects to your terminal 1 9 8 Cord shield 7 Supply ground 6 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 6 Bar code data output 7 Supply power input (Refer to tables on page 11-2.
11 - 6 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 Receive data - Serial data to scanner 6 Transmit data - Serial data from scanner 7 Supply power input (Refer to tables on page 11-2.
Standard Cable Pinouts USB 10 Pin Modular Plug connects to the base 1 2 Data + 3 Tied to supply power 4 Supply ground 5 6 7 5 volt supply power input 8 9 10 Data - 11 - 7 IMAGETEAM™ 2020/5620 System Manual
11 - 8 IMAGETEAM™ 2020/5620 System Manual
12 Maintenance Maintenance Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center. See "Customer Support" on page 13-1 for further information. Cleaning the Scanner’s Window Reading performance may degrade if the scanner’s window is not clean.
Replacing the IT2020 Interface Cable: 1. Turn the power to the host system OFF. 2. Disconnect the base’s cable from the terminal or computer. 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip. 5. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Changing the IT5620 Battery: 1. Remove the screw on the end cap. 2.
If the green LED isn’t illuminated, check that: • • • • The scanner is correctly placed in the base. There is external power or 12 volt host power. Charge mode is turned on. (See "Base Charge Mode" on page 1-5) The battery is not bad or deeply discharged. In some cases, the scanner’s battery may trickle charge to bring it into an acceptable level and then transition to a normal charge cycle. Troubleshooting Scanner Note: Make sure that your scanner’s battery is charged.
1. Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar code is readable. Verify that your bar code symbology is enabled (see Chapter 6). 2. If the scanner still can’t read the sample bar codes, scan All Symbologies on page 6-1.
13 Customer Support Product Service and Repair Hand Held Products provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, return the unit to Hand Held Products (postage paid) with a copy of the dated purchase record attached. Contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
Online Product Service and Repair Assistance You can also access product service and repair assistance online at www.handheld.com. Technical Assistance If you need assistance installing or troubleshooting your scanner, please call your Distributor or the nearest Hand Held Products technical support office: North America/Canada: Telephone: Fax number: E-mail: (800) 782-4263, option 4 (8 a.m. to 6 p.m. EST) (315) 685-4960 natechsupport@handheld.
This warranty shall extend from the time of shipment for the duration published by Hand Held Products for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to Hand Held Products factory or authorized service center for inspection. No product will be accepted by Hand Held Products without a Return Materials Authorization, which may be obtained by contacting Hand Held Products.
13 - 4 IMAGETEAM™ 2020/5620 System Manual
Appendix A Symbology Chart Symbology Code AIM ID ID Hex ID Symbology Code AIM ID ID Hex ID China Post Q ]X0 51 Korea Post ? ]X0 3F Codabar a ]Fm 61 Matrix 2 of 5 m ]X0 6D Codablock F q ]Om 71 MSI g ]Mm Code 11 h ]Hm 68 No Read Code 16K o ]Km 6F Plessey Code Code 39 b ]Am 62 < ]X0 3C l ]Tm 6C Code 32 Pharmaceutical (PARAF) Code 49 67 9C n ]P0 6E PosiCode W ]pm 57 Reduced Space Symbology (RSS14, RSS Limited, RSS Expanded) y ]em 79 Straight 2 of 5
ASCII Conversion Chart (Code Page 1252) Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex 31 1F US 191 3F ? 255 5F _ 319 7F 128 80 € € 192 A0 256 C0 À 320 E0 à 129 81 193 A1 ¡ 257 C1 Á 321 E1 á 130 82 ‚ 194 A2 ¢ 258 C2 Â 322 E2 â 131 83 ƒ 195 A3 £ 259 C3 Ã 323 E3 ã 132 84 „ 196 A4 ¤ 260 C4 Ä 324 E4 ä 133 85 … 197 A5 ¥ 261 C5 Å 325 E5 å 134 86 † 198 A6 ¦ 262 C6 Æ 326 E6 æ 135 87 ‡ 199 A7 § 263 C7 Ç 327 E7 ç 136 88 ˆ 200 A8 ¨ 264
Code Page Mapping of Printed Bar Codes Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should then appear properly. Note: The Code Page option is available for Code 39, Code 93, and Code 128.
Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN 13 EAN 8 9 780330 290951 654 3210 5 UPC-E 0 456123 8
Sample Symbols Code 39 BC321 Code 93 123456-9$ Matrix 2 of 5 6543210 Codabar A13579B Code 2 of 5 123456 RSS-14 (01)00123456789012
Programming Chart 0 1 2 3 4 5 6 7 8 9 A B C D E F Discard Save Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save.
Hand Held Products, Inc. 700 Visions Drive P.O.
