6597 STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll-free number: 1-888-827-9056 or email: customerservice@backyardproductsllc.com Our staff is ready to provide assistance.
(This page intentionally left blank.
#16597 TT 12/03/2010
Building Layout Your Solar Shed can be configured in a variety of ways. Available extender kits can increase the size of your building from 10’ x 8’ to 10’ x 12’ or 10’ x 16’. Also, for added flexibility, the doors can be located on the side or tall wall. This booklet contains instructions for these different configurations. To aid you in constructing your building, the layout plans below show the available Solar Shed configurations.
Door Tall Wall Tall Wall Door Building Size Door Side Wall G la ss G la ss Page # Door Tall Wall Floor Side Wall Side Wall w Door Short Wall Tall Wall Erecting Walls Assemble Trusses Erect Trusses Gable Ends Installing Roof Panels Installing Gable Trim Installing Trim Installing Door Installing Windows Installing Vents Side Wall Short Wall Ext.
Solar Shed Helpful Hints! ■ The Location Positioning of the Solar Shed in relation to your house or garden is an important consideration and unless your house or Solar already faces South you may be missing out on the solar benefits of the sun. To take advantage of solar gain, orient the Solar Shed so that the roof windows are facing southward. If you intend to use the Solar Shed for starting plants or growing into the late fall, it would be best to have it facing 150 East or West of true South.
IMPORTANT!!! IMPORTANTE!!! Building Tip Consejo CON EL FIN DE OBTENER EL PRODUCTO ACABADO DE MEJOR ASPECTO RECOMENDAMOS QUE INSPECCIONE, CLASIFIQUE Y ORGANICE LOS MATERIALES ANTES DE EMPEZAR A MONTAR SU EDIFICIO FOR THE BEST LOOKING FINISHED PRODUCT WE RECOMMEND THAT YOU INSPECT, SORT AND LAY OUT MATERIALS PRIOR TO BEGINNING ASSEMBLY OF YOUR BUILDING AVISO ÚTIL SOBRE LOS MATERIALES HELPFUL MATERIAL NOTICE A C B Wood is a natural product that has inherent blemishes.
PARTS LIST Solar Shed 10’x 8’,10’x12’, 10’x16’ Qty. I.D.* Description Misc. Parts 2 4 2 1 1 4 4 2 2 2 Complete Parts List for 10’ x 8’ Building Qty. I.D.
SITE PREPARATION SITE PREPARATION • Site must be properly leveled. • Site should have natural drainage to eliminate puddling under and around the building. • Site should be covered with plastic film to discourage grass growth under the building and to serve as a vapor barrier. A Before assembling your building, you must first construct a floor system. You can: 925/8” (235.2cm) A. Purchase our optional pre-cut Floor Kit. B.
Parts Needed: A 2 - 48x92-5/8x5/8" Floor Panels B 1 - 23-7/8x92-5/8x5/8" Floor Panel C 6 - 2x4x89-1/2" Floor Joist D 2 - 2x4x72" Bond Boards E 2 - 2x4x48" Bond Boards - 2" and 3" Nails Phoenix 10 x 8 Floor Kit Instructions Optional Floor Kit not supplied with Building Kit For Handy Home optional Wood Floor Kit, refer to instructions included with floor. Floor Instructions maybe different from this manual. A NOTE: Part letters are not stamped on floor kits.
10 x 8 Floor Kit continued FLOOR PANEL ATTACHMENT: C: D: E: Position a 48 x 92-5/8” Floor Panel A flush to the outside edges of sides and back of Floor Frame. Secure panel with two 2” nails at outside corners and one 2” nail at other corners. C 92-5/8" C Position the other 48” x 92-5/8” Floor Panel A flush against first panel and flush to edges of Floor Frame. Secure panel with one 2” nail at each of the four corners.
Phoenix 10 x 4 Floor Extender Kit Instructions Parts Needed: A 2 - 2x4x24" Bond Boards B 2 - 2x4x96" Bond Boards C 6 - 2x4x42-1/2" Floor Joist D 1 - 45-1/2"x96"x5/8" Floor Panels E 1 - 23-7/8"x45-1/2"x5/8" Floor Panels - 2" and 3" Nails Optional Floor Kit not supplied with Building Kit. Follow instructions with Optional Floor Kit, they maybe different than this manual. A A Attach with 3" Nails B 10x8 Floor Note: Floor Kit parts are not stamped with identification letters.
1 No Door Side Wall Assembly ❒2 ❒8 ❒4 ❒2 ❒4 ❒2 ❒2 ❒2 Note: Before beginning assembly, Door Placement, Optional Window Placement, and Building Size must be determined. TN ---------TH ---------TG ---------SN ---------SD ---------1L /1R Angled wall Panel -- Wall Panel -- Narrow Wall Panel Refer to page 2 & 3 before beginning assembly. Nail parts together using two 3” (6.7cm) nails at each connection. B Be sure to nail both TGs together as shown using one 3” (6.7cm) nail.
Side Wall Assembly Cont. Right side wall assembly shown. If building Left side assembly, place wall panels on opposite side of frame. 2” Nails Panels overlap TN by 1/4” (.6cm) TN 1B. Install First Panel 237/8” x 72” (60.6x183cm) as shown. 4 Nail, and follow sequence shown with four 2” (5cm) nails. TH 1B 2 TH TH TH Panel Edge Centered On TH SN SD SD TG TG 3 1 Panel overhangs TG by 3/4” (2cm) 31/2” (9cm) Square Edge Lip Edge 2” Nails Panels overlap TN by 1/4” (.6cm) TN 1C.
Side Wall Assembly Cont. Panels overlap TN by 1/4” (.6cm) 1D. Install Angled Panel 48”x72” (122x183cm) as shown. TN Nail, and follow sequence shown with four 2” (5cm) nails. 1 TH TH 1D SN SD 4 SD 1C TG 3 Square Edge Lip Edge 31/2” (9cm) 1E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
With Door 1 ❒1 ❒4 ❒2 ❒1 ❒2 ❒1 ❒1 ❒1 ❒1 Side Wall Assembly Note: Before beginning assembly, Determine Door Location per illustrations on Page 2. Nail parts together using two 3” (6.7cm) nails at each connection. B Be sure to toe-nail both TGs together as shown using one 3” (6.7cm) nail.
Side Wall Assembly Cont. Right side wall assembly shown. If building left side assembly, place wall panels on opposite side of frame. Panels overlap TN by 1/4” (.6cm) TN SC 1B. Install First Panel 143/8” x 72” (36x183cm) as shown. 4 Nail, and follow sequence shown with four 2” (5cm) nails. TH TH TH 1B Panel Edge Centered On TH SN SD 3 TH SD TG TG 2 1 Panel overhangs TG by 3/4” (2cm) 2” Nails Panels overlap TN by 1/4” (.6cm) TN 7 1C. Install Second Panel 23 /8”x72” (60.6x183cm) as shown.
1D. Install Angled Panel 48”x72” (122x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. Panels overlap TN by 1/4” (.6cm) TN SC 1 TH 1D TH TH SN SD 4 1C SD TG 3 Lip Edge 31/2” (9cm) TG 2 Square Edge 1E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
2 Short Wall Assembly ❒1 ❒1 ❒5 ❒1 ❒1 VO UL SD 2B* 2C* 2 x 6 x 925/8” 5 x 14 x 235cm 2 x 4 x 925/8” 5 x 10 x 235cm 2 x 4 x 33” 5x 10 x 84cm 443/8” x 351/4” 113 x 89cm 48” x 351/4” 122 x 89cm ---------------------------Wall Panel Wall Panel * Refers To Step Panel Is Used A 2A. Arrange 1- VO, 5- SDs and, 1-UL as shown. 3” Nails A Nail parts together using two 3” (6.7cm) nails at each connection. VO 36” (91.4cm) 2A SD SD SD SD SD UL MEASURE ON EDGE 231/2” (59.7cm) 241/2” (62.
Short Wall Assembly Cont. 2C. Install Second Panel 48”x351/4” (122x89cm) as shown. VO 3 Nail, and follow sequence shown with four 2” (5cm) nails. 1 SD 48”x351/4” (122x89cm) 2C 2 4 Square Edge Lip Edge 2D 2D. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
2 Extended Short Wall Assembly 12’ Long Wall A ❒1 ❒1 ❒8 ❒1 ❒1 ❒1 ❒1 ❒1 VO VD SD UL SR 2B* 2C* 2D* 2 x 6 x 925/8” 2 x 6 x 451/2” 2 x 4 x 33” 2 x 4 x 925/8” 2 x 4 x 451/2” 451/2”x 351/4” 443/8” x 351/4” 48” x 351/4” Wall Panel Wall Panel Wall Panel 5 x 14 x 235cm 5 x 14 x 115.5cm 5 x 10 x 83.8cm 5 x 10 x 235cm 5 x 10 x 115.5cm 115.5 x 89cm 113 x 89cm 122 x 89cm * Refers To Step Panel Is Used 2A. Arrange 1- VO, 1- VD, 8 - SDs, 1- TJ and, 1 - SR as shown.
2C. Install Second Panel 48”x351/4” (122x89cm) as shown. 2C Nail, and follow sequence shown with four 2” (5cm) nails. VO VD SD SD SD 3 1 48”x35 1/4” (122x89cm) UL 2 4 Panel overhangs TJ by 3/4” (2cm) Lip Edge Square Edge Lip Edge Square Edge 2D. Install Third Panel 451/2”x351/4” (116x89cm) as shown. 2D Nail, and follow sequence shown with four 2” (5cm) nails. VD SD VO 3 1 1 1 45 /2”x35 /4” (116x89cm ) 2” Nails 4 2 Square Edge Square Edge Lip Edge 8” (20cm) 2E.
2 Extended Short Wall Assembly 16’ Long Wall ❒ 11 SD ❒ 1 VO ❒ 1 UL ❒ 2 VD ❒ 2 SR ❒ 1 2C* Wall Panel ❒ 1 2C* Wall Panel ❒ 2 2B,D* Wall Panel 2 x 4 x 33” 2 x 6 x 925/8” 2 x 4 x 925/8” 2 x 6 x 451/2” 2 x 4 x 451/2” 48-3/8 x 35-1/4” 44-3/8” x 35-1/4” 45-1/2” x 35-1/4” 5 x 10 x 83.8cm 5 x 14 x 235cm 5 x 10 x 235cm 5 x 14 x 115.5cm 5 x 10 x 115.5cm 122 x 89.5cm 113 x 89.5cm 116 x 89.5cm * Refers To Step Panel is Used 2A. Arrange 1- VO, 2 - VD, 11 - SDs, 1- UL and, 2 - SR as shown.
16’ Short Wall Cont. 2B. Install First Panel 451/2”x351/4” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD SD SD VD VO SD SD SD SD SR SD 1 3 SD UL SR 4 2B SD SD 451 /2”x35 1 /4” (116x89 cm ) SD 2 Square Edge 5-1/2” (14 cm) Square Edge 8” (20 cm) 2C. Install Second Panel 443/8”x351/4” (113x183cm) and Third Panel 48” x 351/4” (122x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails.
16’ Short Wall Cont. 2D. Install Fourth Panel 451/2”x351/4” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD SD 3 VD VO SD SD 1 SD SD SD 451/2”x35 1/4” (116x89 cm ) 4 SR Square Edge 2” Nails TR 2 8” (20 cm) Lip Edge 8” (20 cm) 2E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
No Door 3 ❒1 ❒5 ❒1 ❒1 ❒1 Tall Wall Assembly VO TH UL 3B* 3C* Top Plate Wall Stud Bottom Plate Wall Panel Wall Panel 2 x 6 x 925/8” 2 x 4 x 691/2” 2 x 4 x 925/8” 443/8” x 72” 48” x 72” 5 x 14 x 235cm 5 x 10 x 176cm 5 x 10 x 235cm 113 x 183cm 122 x 183cm * Refers To Step Panel Is Used 3A. Arrange 1- VO, 5- THs and, 1-UL as shown. A A Nail parts together using two 3” (6.7cm) nails at each connection.
Tall Wall cont. VO 3B. Install First Panel 443/8”x72” (113x183cm) as shown. 1 3 Nail, and follow sequence shown with four 2” (5cm) nails. TH TH 443/8”x72” (113x183cm) TH UL 3B Panel flush to edge of (SD) 4 TH TH 2 Panel overhangs UL by 3/4” (2cm) Lip Edge 3C. Install Second Panel 48”x72” (122x183cm) as shown. VO Nail, and follow sequence shown with four 2” (5cm) nails.
Tall Wall cont. 3D. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
3 Tall Wall Assembly with Door ❒1 ❒5 ❒1 ❒1 ❒1 ❒1 VO TH UL 3B* 3C* SC Top Plate Wall Stud Bottom Plate Wall Panel Wall Panel 2 x 6 x 925/8” 2 x 4 x 691/2” 2 x 4 x 925/8” 143/8” x 72” 443/8” x 72” 2 x 4 x32” 5 x 14 x 235cm 5 x 10 x 176cm 5 x 10 x 235cm 36 x 183cm 112.7 x 183cm 5 x 10 x 81.3cm * Refers To Step Panel Is Used A 3A. Arrange 1- VO, 5- THs, 1-SC and, 1-UL as shown. A Nail parts together using two 3” (6.7cm) nails at each connection.
Tall Wall cont. 3B VO 3B. Install First Panel 143/8”x72” (36x183cm) as shown. SC Nail, and follow sequence shown with four 2” (5cm) nails. 1 3 TH TH 143/8”x72” TH (36.5x183cm TH) TH 32” (81.3cm) Door Opening Panel flush to edge of (TH) UL 2 4 Panel overhangs TJ by 1” (2.5cm) 2” Nails VO 3C. Install Second Panel 443/8”x72” (112x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails.
Tall Wall cont. 3D. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
No Door 3 Extended Tall Wall Assembly 12’ Long Wall ❒1 ❒1 ❒8 ❒1 ❒1 ❒1 ❒1 ❒1 VO VD TH UL SR 3B* 3C* 3D* Wall Panel Wall Panel Wall Panel 2 x 6 x 925/8” 2 x 6 x 451/2” 2 x 4 x 691/2” 2 x 4 x 925/8” 2 x 4 x 451/2” 451/2” x 72” 443/8” x 72” 48” x 72” 5 x 14 x 235cm 5 x 14 x 115.5cm 5 x 10 x 176cm 5 x 10 x 235cm 5 x 10 x 115.5cm 116 x 183cm 113 x 183cm 122 x 183cm * Refers To Step Panel is Used 3A. Arrange 1- VO, 1- VD, 8 - SDs, 1- UL and, 1 - SR as shown. A 3A Nail parts together using two 3” (6.
VO VD 3B TH TH TH TH TH TH 1 4 443/8”x72” SD (113x89cm) 3B. Install First Panel 443/8”x72” (113x183cm) as shown. Panel flush to edge of (TH) Nail, and follow sequence shown with four 2” (5cm) nails. UL 2 3 2” Nails Panel overhangs UL by 1” (2.5cm) Lip Edge 3C VD 3C. Install Second Panel 48”x72” (122x183cm) as shown. TH VO TH TH 2 1 48”x72” (122x89cm) Nail, and follow sequence shown with four 2” (5cm) nails. UL 4 3 Panel overhangs UL by 1” (2.
VD 3D VO 1 2 1 3D. Install Third Panel 451/2”x72” (116x183cm) as shown. 45 /2”x72” (116x183cm) TH Panel flush to edge of (TH) Nail, and follow sequence shown with four 2” (5cm) nails. 4 3 Panel overhangs UL by 1” (2.5cm) 2” Nails Square Edge Square Edge 8” (20cm) 3E VO VD 3E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
3 No Door Extended Tall Wall Assembly 16’ Long Wall ❒ 1 VO ❒ 2 VD ❒ 11TH ❒ 1 UL ❒ 2 SR ❒ 1 3C* Wall Panel ❒ 1 3C* Wall Panel ❒ 2 3B,D* Wall Panel 2 x 6 x 925/8” 2 x 6 x 451/2” 2 x 4 x 691/2” 2 x 4 x 925/8” 2 x 4 x 451/2” 48” x 72” 443/8” x 72” 451/2” x 72” 5 x 14 x 235cm 5 x 14 x 115.5cm 5 x 10 x 176.5cm 5 x 10 x 235cm 5 x 10 x 115.5cm 122 x 183cm 113 x 183cm 116 x 183cm * Refers To Step Panel is Used A 3A. Arrange 1- VO, 2 - VD, 11 - THs, 1- UL and, 1 - SR as shown.
3B. Install First Panel 451/2”x72” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. 2” Nails VD VD VD 4 451/2”x72” (116x89cm) 2 3B 3 1 Panel overhangs UL by 1” (2.5cm) Square Edge Square Edge 5-1/2” (14 cm) 8” (20 cm) 3C. Install Second Panel 443/8”x72” (113x183cm) and Third Panel 48” x 72” (122x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD VD 4 2 48”x72” (122x183cm) 3C 3 Panel overhangs UL by 1” (2.
16’ Tall Wall Cont. 3D. Install Fourth Panel 451/2”x72” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD 2” Nails 3 VD 451/2”x72” (113x183cm) 1 3D 4 2 Panel overhangs UL by 1” (2.5cm) Square Edge 8” (20 cm) Lip Edge 8” (20 cm) 3E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
With Door 3 Extended Tall Wall Assembly 12’ Long Wall 3A. Arrange 1- VO, 1- VD, 8 - THs, 1- UL, 1- SC and, 1 - SR as shown. ❒1 ❒1 ❒8 ❒1 ❒1 ❒1 ❒1 ❒1 ❒1 VO VD TH UL SR 3B* 3C* 3D* SC Wall Panel Wall Panel Wall Panel 2 x 6 x 925/8” 2 x 6 x 451/2” 2 x 4 x 691/2” 2 x 4 x 925/8” 2 x 4 x 451/2” 451/2” x 72” 443/8” x 72” 143/8” x 72” 2 x 4 x32” 5 x 14 x 235cm 5 x 14 x 115.5cm 5 x 10 x 176cm 5 x 10 x 235cm 5 x 10 x 115.5cm 116 x 183cm 113 x 183cm 36 x 183cm 5 x 10 x 81.
Extended Tall Wall Assembly cont. VD vo 3B TH TH TH TH TH 1 3 451/2”x72” SD (116x89cm) 3B. Install First Panel 451/2”x72” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. 4 UL 2 Panel overhangs UL by 1” (2.5cm) 2” Nails Square Edge Square Edge 5-1/2” (14 cm) 8” (20 cm) 3C VD vo 3C. Install Second Panel 443/8”x72” (113x183cm) as shown. TH TH TH 3 SD 1 SD 443/8”x72” (116x89cm) Nail, and follow sequence shown with four 2” (5cm) nails.
VD VO 3D TH 3D. Install Third Panel 143/8”x72” (36x183cm) as shown. 3 SD 1 TH SD SD 143/8”x72” (36.5x183cm) Nail, and follow sequence shown with four 2” (5cm) nails. Panel flush to edge of (TH) 4 2 UL Panel overhangs UL by 1” (2.5cm) 2” Nails 3E VD VO TH TH SD SD 3E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
3 ❒ 1 VO ❒ 2 VD ❒ 11 TH ❒ 1 UL ❒ 2 SR ❒ 1 3C* Wall Panel ❒ 1 3C* Wall Panel ❒ 2 3B,D* Wall Panel ❒ 1 SC Extended Tall Wall Assembly with Door 16’ Long Wall 2 x 6 x 925/8” 2 x 6 x 451/2” 2 x 4 x 691/2” 2 x 4 x 925/8” 2 x 4 x 451/2” 143/8” x 72” 443/8” x 72” 451/2” x 72” 2 x 4 x32” 5 x 14 x 235cm 5 x 14 x 115.5cm 5 x 10 x 176.5cm 5 x 10 x 235cm 5 x 10 x 115.5cm 36 x 183cm 113 x 183cm 116 x 183cm 5 x 10 x 81.3cm * Refers To Step Panel is Used 3A.
3B. Install First Panel 451/2”x72” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD VD VD 3 1 451/2”x72” (116x183cm) 3B 4 2 Panel overhangs UL by 1” (2cm) 2” Nails Square Edge Square Edge 5-1/2” (14 cm) 8” (20 cm) 3C. Install Second Panel 443/8”x72” (113x183cm) and Third Panel 143/8” x 72” (36x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD VD 3 VD 3 1 3C 1 443/8”x72” (113x183cm ) 4 4 2 Panel overhangs UL by 1” (2.
Extended Tall Wall Cont. 3B. Install Fourth Panel 451/2”x72” (116x183cm) as shown. Nail, and follow sequence shown with four 2” (5cm) nails. VD VD 2 451/2”x72” (116x183cm) 1 3D 4 Panel overhangs UL by 3/4” (2cm) 3 2” Nails Square Edge Square Edge 8” (20 cm) 3E. Once all panels are in place secure to frame using 2” (5cm) nails spaced every 8” (20cm).
4 Erecting Walls All Sizes ❒2 ❒1 ❒1 Assembled Side Walls Assembled Tall Wall Assembled Short Wall 4A. Stand Tall Wall as shown. A Nail 3/4” (2cm) overhang to floor using 2” (5cm) nails spaced 12” (30cm) apart. B Nail frame to floor using 3” (7.6cm) nails as shown. C Making sure wall is vertically level, temporarily secure HJ for support as shown. 4A Note: Erect Extended Walls Same way. Tall Wall HJ C B 30 0” m 12 4.8c B A 925/8”, 1381/8”, 1835/8” 235.2cm, 350.8cm, 466.
4B. Position Right Side Wall Assembly as Shown. A Secure Side Wall to Tall Wall using 2” (5 ) Nails. 3/4” (2 ) overhang to floor using 2” (5 B Nail nails spaced 12” (30 )apart. cm cm cm) cm A B C inside walls together using C Secure 3” (7.6 ) nails. cm D Nail frame to floor using 3” (7.6 cm) nails as shown.
5 Assembling Trusses All size Buildings 5A. Lay out parts for ONE RIGHT TRUSS as shown: one TF and one RO. Use gusset as a guide. HINT: Ensure 129-15/16” dimension. RIGHT TRUSS Parts List 1 TF Rafter 2 x 4 x 647/8” 1 RO Rafter 2 x 4 x 9313/16” 1 -- Gusset ---- 5 x 10 x 165cm 5 x 10 x 238cm ---- 5B. Assemble right truss using fourteen 2” (5cm) nails in gusset. Note: Glue may be used in addition to nails for added strength (glue not supplied with kit).
5 Assembling Trusses All size Buildings 5C. Lay out parts for ONE LEFT TRUSS as shown: one TF and one RO. Use gusset as a guide. HINT: Ensure 129-15/16” dimension. LEFT TRUSS Parts List 1 TF Rafter 2 x 4 x 647/8” 1 RO Rafter 2 x 4 x 9313/16” 1 -- Gusset ---- 5D. Assemble left truss using fourteen 2” (5cm) nails in gusset. Note: Glue may be used in addition to nails for added strength (glue not supplied with kit).
5 Assembling Trusses All size Buildings 5E. Lay out parts for center truss as shown: one TF and one RO. Use gusset as a guide. Hint: Ensure 129-15/16” dimension. CENTER TRUSS Parts List 1 TF Rafter 2 x 4 x 647/8” 1 RO Rafter 2 x 4 x 9313/16” 2 -- Gussets ---- 5 x 10 x 165cm 5 x 10 x 238cm ---- 5F. Assemble center truss using fourteen 2” (5cm) nails in gusset. 5G. Carefully flip truss over and finish assembling using fourteen 2” (5cm) nails in gusset.
5 Assembling Trusses All size Buildings 10x8 Parts List ❒5 TF Rafter ❒5 RO Rafter ❒8 -- Gussets 2 x 4 x 647/8” 2 x 4 x 9313/16” ---- 5 x 10 x 165cm 5 x 10 x 238cm ---- 10x12 Parts List ❒7 TF Rafter 2 x 4 x 647/8” ❒7 RO Rafter 2 x 4 x 9313/16” ❒ 12 -- Gussets ---- 5 x 10 x 165cm 5 x 10 x 238cm ---- 10x16 Parts List ❒9 TF Rafter 2 x 4 x 647/8” ❒9 RO Rafter 2 x 4 x 9313/16” ❒ 16 -- Gussets ---- 5 x 10 x 165cm 5 x 10 x 238cm ---- Truss Assembly Chart 5H 10 x 8 Building 2 Single Gusset Trusses 3 Doub
6 Erect Trusses All size Buildings 6A. Erect trusses as shown by using the IEs as spacers between trusses on both the tall and short wall. A Make sure the single gusset trusses are located next to side walls with the gussets to the inside. B Secure trusses to VO using two 3” (7.6cm) Screws. C Secure IEs to VO using three 2” (5cm) nails.
6 Erect Trusses All Size Buildings Cont. Install Rafter Tie and Rafter Spacer Refer to Step that correlates to the size building you are installing. 10x8 Parts List ❒1 CG Rafter Tie 1 x 2 x 91 1 / 8 ” ❒4 BU Rafter Spacer 1x2x21 1 / 4 ” 2.5 x 5 x 231.4 cm 2.5 x 5 x 54 cm 6C. 10 x 8 Starting with the window side single gusset rafter, place CG Rafter Tie in notch as shown (leaving 3/4” gap A) attach using one 2” (5cm) nail. Next attach BU Rafter Spacer using three 11/4” (3cm) screws.
Install Rafter Tie and Rafter Spacer. Refer to Step that correlates to the size building you are installing. 6C. 10 x12 & 10 x 16 Starting with the left side single gusset rafter, place CG Rafter Tie in notch as shown (leaving 3/4” gap A) attach using one 2” (5cm) nail. Next attach BU Rafter Spacer using three 11/4” (3cm) screws. Continuing in this manner until all rafters are completed will ensure proper spacing between rafters.
7 ❒2 ❒2 Gable Ends NOTE: A 1/2” PVC or Copper Pipe may be inserted into gusset holes for hanging plants (Piping not included in Kit). 7A. Place Gable Panel as shown and nail in place using 2” (5cm) nails spaced 8” (30cm). 7A 7B. Place Gable Spacer above gable panel as shown and attach using five 2”(5cm ) nails. 7C. Completed Gable End. Repeat same steps for opposite side of building.
8 ❒1 ❒1 ❒1 Installing Roof Panels 10 x 8 Installation 8A. 8A* 8B* 8C* Roof panel Roof Panel Roof panel 48” x 921/4” 157/8” x 921/4” 235/8” x 921/4” 122 X 234cm 40 X 234cm 60 X 234cm * Refers to step Panel is used 8B. Install second roof panel 157/8”x921/4” (40 X 234cm) same as first. Once both roof panels are in place secure to trusses using 2” (5cm) nails spaced 8” (20cm) as shown. Install first roof panel 48”x921/4” (122 X 234cm) on tall wall and nail in sequence shown using four 2”(5cm) nails.
8 ❒1 ❒1 ❒1 ❒1 ❒1 ❒1 ❒1 Installing Roof Panels 10 x 12 Installation 8A* 8A* 8B* 8B* 8C* 8C* 8C* 48 x921/4” 48 x4513/16” 157/8 x921/4” 157/8 x4513/16” 235/8 x921/4” 235/8 x4513/16” 72 x4513/16” Roof panel Roof panel Roof Panel Roof Panel Roof Panel Roof Panel Roof panel 122X234cm 122X116.4cm 40X234cm 40X116.4cm 60.6X234cm 60.6X116.4cm 183X116.4cm Substitute 2 Glass Panels for Glass Extender on the above item. * Refers to step Panel is used 8A 1 3 2 4 1 3 48”x45-13/16” 1/8” (.
8 Installing Roof Panels 10 x 16 Installation ❒1 ❒2 ❒1 ❒2 ❒1 ❒2 ❒2 48 x921/4” 48 x4513/16” 157/8 x921/4” 157/8 x4513/16” 235/8 x921/4” 235/8 x4513/16” 72 x4513/16” 122X234cm 122X116.4cm 40X234cm 40X116.4cm 60.6X234cm 60.6X116.4cm 182X116.4cm * Refers to step Panel is used 3 1 3 48”x45-13/16” 4 Roof panel Roof panel Roof Panel Roof Panel Roof Panel Roof Panel Roof panel Substitute 2 Glass Panels for Glass Extender. 8A.
10 Installing Gable Trim 10A. Place Plywood Gable Cap flush to top of roof panel. *Hint* Use a scrap piece of wood to help align to top of roof ❒2 ❒2 ❒2 ❒2 ❒2 JB KN HN --- Gable Trim Gable Trim Gable Trim Plywood Gable Cap Soffit End Cap 1 x 4 x 425/8” 1 x 4 x 877/8” 1 x 3 x795/16” 97/8” x 295/16” 77/8 x315/16 x71/2” 2 x 10 x 130cm 2 x 10 x 223.2cm 2 x 7.6 x 201.4cm 24 x 74cm 20x10x19cm scrap wood Plywood Gable Cap Secure Plywood Gable Cap in place using seven 2” (5cm) nails. 10A JB 10B.
11 Install Corner Trim ❒2 ❒2 ❒2 ❒2 CK GT CS CF Corner Trim w/angle Corner Trim Corner Trim Corner Trim 11A. Assemble Corner Trim GT and Corner Trim CS as shown using seven 2” (5cm) nails. Offset GT 1/2” at top and flush at bottom. Flush GT CS 2 x 6 x 98cm 2 x 6 x 181.6cm 2 x 5 x 183cm 2 x 5 x 89cm 11B. Assemble Corner Trim CK and Corner Trim CF as shown using five 2” (5cm) nails. Assemble two of these corners making sure to assemble one right and one left Corner Trim Assembly.
10 x 8 Building Parts List 12 ❒1 ❒1 Install Fascia Trim KT KI Fascia Trim angled Fascia Trim 1 x 4 x 933/8” 1 x 4 x 933/8” 2 x 10 x 237cm 2 x 10 x 237cm 1 x 4 x 933/8” 1 x 4 x 451/2” 1 x 4 x 933/8” 1 x 4 x 451/2” 2 x 10 x 237cm 2 x 10 x 115.5cm 2 x 10 x 237cm 2 x 10 x 115.5cm 1 x 4 x 933/8” 1 x 4 x 451/2” 1 x 4 x 933/8” 1 x 4 x 451/2” 2 x 10 x 237cm 2 x 10 x 115.5cm 2 x 10 x 237cm 2 x 10 x 115.5cm 10 x 12 Building Parts List All Building Sizes ❒1 ❒1 ❒1 ❒1 12.
13 Building Parts List 1 pcs. — Doors 1 pcs. — Continuous Hinge 2 pcs. ZO Door Trim Installing Door All Building Sizes 13A 3/4" Screws Flush 5/8 x 3 x 72" 13-A: Position Continuous Hinge on edge of Door with lobe up and overhanging outside face edge of Door. Piano Hinge should be flush to top of Door as shown. Secure with twelve 3/4” (1.9cm) Hinge screws. Make sure there is a screw in each hole.
1 -- Door Stop 2 DH -- Door Stile Installing Door cont. 13-D:Cut bottom plate in door opening flush to studs. Install 1/2 x 3/4 x 68” Door Stop with 1-1/2” finish nails. Keep 5/8” to outside of stud and keep 1/2” side to stud. Use wood glue (not included) for added strength. 1/2 x 3/4 x68” 5/8x3x 30 5/8” 20 x 10 x 19cm 2 x 4 x 77.8cm 5/8" 13D ZO Siding 1-1/2" Finish Nail Door Assembly 3" Screw Install Door Stiles (DH) with 1” screws to the center of the Doors.
Installing Door cont.
Mark hole location as indicated and drill one 1/2” hole straight through door. Insert Knob assembly through outside of door. With level handle vertical, fasten with machine screws provided as in step 2. Position inside handle with long end towards left door. Keep the handle back approx. 1-1/2” from front of door as shown in Step 4. Note, depending on the building you purchased, this dimension may vary. Tighten allen screw and test handle. Turn handle to the right and shut door.
4 -3 -2 -2 Roll Installing Windows 15 Each 4’ Glass Extender Follow these basic steps for extender glass options. 15-A: We require metal drip edge (not included) also be applied before shingling and installing windows. Install to all outside edges. See illustration below for more information.
15-C: Place windows in opening between rafters, then secure in place using Mullion Strips (Wide to the outside & Narrow to the inside). Mullion Strips will cover outside edges of the window flange and the pan head screws will pass through the mullion strip, between the window flanges into the center of the rafters. Use one 11/4” (3cm) pan head screw for each hole in all mullion strips and tighten snugly.
❒4 ❒4 ❒4 Installing Vents 16 ---- Adjustable Vents 6 x 12” Exterior Vents 8 x 16” Interior Vent Spacer 9 x 15” 15 x 30.5cm 20.3 x 40.6cm 23 x 38 cm 16. Install vents in sequence shown 1 through 3. Screw in place with four 3/4”(2cm) screws in each part. Inside Vent Spacer Exterior Vent Inside Adjustable Vent 3/4" Screws Screws 3/4” (1.9cm) 2 Screws 3/4”” (2.
17 Installation of Optional Large Square Window (not included) I.D. ---RI DV DT ---- Determine location for optional window. Locating window opening is easiest when done from inside the building. 17 A. Arrange and attach part RI as shown. (from Large Square Window kit). Secure to Description Size Window Sill Plates 2 x 4 x 22-1/2” Vertical Trim 1 x 3 x 30-1/4” Horizontal Trim 1 x 3 x 28-3/4” 3” Nails, 2” Nails, 1-1/2” Finish Nails 17A frame using four 3” (6.7cm) nails. CM 57.1cm 76.9cm 73.1cm Qty.
INSTALLING SHINGLES Important: Make sure shingles overhang glass by approx. 3”. A 1" (2.5 cm) 1/2" (1.3 cm) 1" (2.
Notes:
Notes:
Notes:
WARRANTY Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for one year. 2. All hardware and metal components are warranted for two years. 3. Trim is warranted for 10 years. 4. Waferboard siding and sheathing is warranted for two years. 5. SmartSide™ siding is warranted for 10 years on all Marco series buildings and 15 years on all Premier Series buildings. 6.
Important! Please follow these instructions. This kit may be different from the one specified in instruction booklet. 07/31/2006 COMBINATION 8X8 and 10X8 FLOOR KIT This floor kit will build either the 10’ wide or 8’ wide x 7’ 8-5/8” deep floor size FOR MARCO SERIES, SOLAR SHED AND MWP IMPERIAL ONLY This floor kit is for 10’ x 7’ 8-5/8” and 8’ x 7’ 8-5/8” buildings. Please refer to the appropriate pages of this instruction manual to build the floor size needed.
Parts Needed: A 2 - 48x92-5/8x5/8" Floor Panels C 5 - 2x4x89-1/2" Floor Joist D 2 - 2x4x72" Bond Boards F 2 - 2x4x24" Bond Boards - 2" and 3" Nails F L O O R K I T I N S T RU C T I O N S FOR 8X8 BUILDINGS ACTUAL SIZE 96” WIDE x 92-5/8” DEEP NOTE: Part letters are Not stamped on floor kits. ASSEMBLY OF 8’ x 92-5/8” FLOOR FRAME IMPORTANT! If you will be storing heavy items (such as lawn tractor, motorcycle, snowmobile etc.) we recommend you upgrade from 24” on center (61 cm) to 12” on center (30.
8X8 F L O O R K I T I N S T RU C T I O N S CONTINUED FLOOR PANEL ATTACHMENT: C: Position a 48 x 92-5/8” Floor Panel A flush to the outside edges of sides and back of Floor Frame. Secure panel with two 2” nails at outside corners and one 2” nail at other corners. C 92-5/8" A C F D 96" D: Position the other 48” x 92-5/8” Floor Panel A flush against first panel and flush to edges of Floor Frame. Secure panel with two 2” nails at outside corners and one 2” nail at each of other corners.
Parts needed to cut: B 1 - 23-7/8x92-5/8x5/8" Floor Panel C 1 - 2x4x89-1/2" Floor Joist E 2 - 2x4x48" Bond Boards - 2" and 3" Nails 8X8 OPTIONAL SHELF I N S T RU C T I O N S Cut Cut A C B (1) - 89-1/2" Board C cut down to 88" (1) - 23-7/8x92-5/8" Panel B cut down to 23-7/8x89-1/2" Cut 23-3/16" E 24-11/16" (2) - 48" Board E cut down to 2 pieces of 24-11/16 and 23-3/16" SHELF PARTS TO CUT: Cut the 89-1/2” Board C down to 88”. Cut both 48” boards E at 24-11/16” leaving 23-3/16”.
Parts Needed: A 2 - 48x92-5/8x5/8" Floor Panels B 1 - 23-7/8x92-5/8x5/8" Floor Panel C 6 - 2x4x89-1/2" Floor Joist D 2 - 2x4x72" Bond Boards E 2 - 2x4x48" Bond Boards - 2" and 3" Nails F L O O R K I T I N S T RU C T I O N S FOR 10X8 BUILDINGS ACTUAL SIZE 120” WIDE x 92-5/8” DEEP NOTE: Part letters are Not stamped on floor kits. ASSEMBLY OF 10’ x 92-5/8” FLOOR FRAME IMPORTANT! If you will be storing heavy items (such as lawn tractor, motorcycle, snowmobile etc.
10X8 F L O O R K I T I N S T RU C T I O N S CONTINUED FLOOR PANEL ATTACHMENT: C: D: E: Position a 48 x 92-5/8” Floor Panel A flush to the outside edges of sides and back of Floor Frame. Secure panel with two 2” nails at outside corners and one 2” nail at other corners. C 92-5/8" C Position the other 48” x 92-5/8” Floor Panel A flush against first panel and flush to edges of Floor Frame. Secure panel with one 2” nail at each of the four corners.
NOTES: 7
NOTES: 8