6770-C Call Us First! DO NOT RETURN TO STORE. For questions on assembly or for general inquiries, you may contact us in the following ways: Call customer service: 1-877-743-3400 AVOID THE WAIT! visit us online at help.backyardproducts.com Submit a help request Answers to frequently asked questions Live chat with an agent Did you enjoy building your shed? LERS INSTAL D WANTE JOIN OUR TEAM AND MAKE UP TO $1,500/WEEK* pl y si .
Win $500 A new winner is selected every 2 months. Review your product for the chance to win a $500 Visa Gift Card. How to Enter: Open camera. Aim. Tap. et or Scan QR code above. Click ‘write a review’ Find your product. Tell us what you think. s .n it v is ba ckyardr ew evi Submit your review. You’ll be notified by e-mail if you’ve won the $500 gift card. Write a Backyard Products, LLC. product review at backyardreviews.net for a chance to win a $500 Visa gift card.
GABLE 10' x 8' (305 x 244) ASSEMBLY MANUAL BUILDING SIZE BASE MODEL ADD ONE 10' x 4' ADD TWO 10' x 4' 10' x 8' (305 x 244 cm) 10' x 12' (305 x 365,8 cm) 10' x 16' (305 x 487,7 cm) 16770-C 12/20/2021 ACTUAL FLOOR SIZE 10' x 7' 8-5/8" (305 x 235,3 cm) 10' x 11' 8-5/8" (305 x 357,2 cm) 10' x 15' 8-5/8" (305 x 479 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.
TOOLS Required ❑ Phillips Screwdriver Optional ❑ Tool Belt/ Nail Pouch ❑ Utility Knife ❑ Shingle Blades ❑ Drill / Driver ❑ 3/8" Drill Bit ❑ #2 Philips Drive Bit ❑ Tin Snips (for drip edge) ❑ Caulk Gun ❑ Hammer ❑ Chalk Line ❑ Paint Tools ❑ Level ❑ Nail Gun ❑ Pencil ❑ Safety Glasses ❑ Tape Measure ❑ Ladder ❑ Square • gun nails ❑ Gloves or Safety! Always use approved safety glasses during assembly. HELPFUL REMINDER SYMBOLS Look for these symbols for helpful reminders throughout this manual.
PARTS IDENTIFICATION AND SIZES Part identification is stamped on some parts. RS WOOD SIZE CONVERSION CHART Treated lumber is stamped: Nominal Board Size RS • Check these locations for part stamp. 10x8' 10x12' 10x16' Actual Size 2x4 ..............1-1/2" x 3-1/2" (3,8 x 8,9 cm) 1x4 .................3/4" x 3-1/2" (1,9 x 8,9 cm) 2x3 ..............1-1/2" x 2-1/2" (3,8 x 6,3 cm) 1x3 .................3/4" x 2-1/2" (3,8 x 6,3 cm) PARTS LIST WALL INVENTORY YOUR PARTS before you begin.
WALL PANEL & DOORS PARTS LIST x1 RIGHT x1 LEFT x4 3/8 x 48 x 72" x2 (1 x 122 x 183 cm) x1 x1 x1 x1 x1 x1 LEFT DOOR RIGHT DOOR ROOF PANELS 48" x 96" (122 x 244 cm) x2 19" x 48" (48 x 122 cm) x4 Roof panels are 7/16" (11 mm) thick.
ROOF PANELS 10 x 8' x2 48" x 96" (122 x 244 cm) x4 Roof panels are 7/16" (11 mm) thick. x1 10 x 12' x2 x2 10 x 16' x2 x2 2" (5,0 cm) 19" x 48" (48 x 122 cm) 1 lb. of 2" (5,0 cm) 48" x 96" (122 x 244 cm) x6 19" x 48" (48 x 122 cm) Roof panels are 7/16" (11 mm) thick. x2 48" x 48" (122 x 122 cm) 2" (5,0 cm) 1 lb. of 2" (5,0 cm) 48" x 96" (122 x 244 cm) x8 19" x 48" (48 x 122 cm) Roof panels are 7/16" (11 mm) thick. x4 48" x 48" (122 x 122 cm) 2" (5,0 cm) 1 lb.
ADDITIONAL MATERIALS FOUNDATION OR FLOOR MATERIALS • Your shed kit does not include a wood floor frame or floor panel materials. • See page 8 for the additional oor panel sizes and quantities required. • This shed does not include any leveling materials. • See the FLOOR LEVELING section on page 10 for recommended methods and suggested materials to properly level your oor, as this will vary depending on your speci c site.
CONCRETE FOUNDATION If you choose to install your kit on a concrete slab refer to the diagram below. Install the sill plates on the foundaton as shown, and continue on to page 21. Treated Sill Plate Caulk between sill plate and concrete.
FLOOR FRAME (Not Included) 10 x 8' x2 x2 x6 2 x 4 x 48" (5 x 10 x 122 cm) 10 x 12' x6 x4 x4 x6 2 x 4 x 45" (5 x 10 x 114,3 cm) 10 x 16' You may need treated 2 x 4" boards cut to size and nails to complete your floor. Floor panel sizes and quantities are shown below. MUST be treated lumber.
OPTIONAL WOOD FRAME FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS (Typical for 10' x 12' Kit) Seam Runners are generally 12" (30,5 cm) from ends of floor frame and under seams. 4x4 Runners (not included). 12" (30,5 cm) 40-5/16" (102,4 cm) Centered MATERIAL REQUIRED DO Measurements to centers of 4x4's.
10' x 8' FLOOR FRAME (Not Included) PARTS REQUIRED: x28 3" (7,6 cm) x2 2 x 4 x 72" (5 x 10 x 183 cm) Treated Wood x6 2 x 4 x 89-1/2" (5 x 10 x 227 cm) Treated Wood x2 2 x 4 x 48" (5 x 10 x 122 cm) Treated Wood BEGIN 1 Orient parts as shown on flat surface. Measure and mark from end of boards. R Secure with (2) 3" nails at each mark. D O O FINISH You have finished your 10' x 8' floor frame. If building 10' x 8' kit go to page 13. If building 10' x 12' kit go to page 11.
10 x 12' FLOOR FRAME (Not Included) PARTS REQUIRED: x28 3" (7,6 cm) x2 2 x 4 x 72" (5 x 10 x 183 cm) x2 2 x 4 x 48" (5 x 10 x 122 cm) x6 2 x 4 x 45" (5 x 10 x 114,3 cm) BEGIN You will build (2) floor sections. Follow steps 1-3 on page 10 to build front 10' x 8' floor section 1. 2 Orient parts as shown on flat surface to build back section 2. Measure and mark each dimension from end of boards. 3 Secure with (2) 3" nails at each mark. Go to page 14.
10 x 16' FLOOR FRAME (Not Included) PARTS REQUIRED: x28 3" (7,6 cm) x2 2 x 4 x 72" (5 x 10 x 183 cm) x2 2 x 4 x 48" (5 x 10 x 122 cm) x6 2 x 4 x 93 " (5 x 10 x 236,2 cm) BEGIN You will build (2) floor sections. Follow steps 1-3 on page 10 to build front 10' x 8' floor section 1. 2 Orient parts as shown on flat surface to build back section 2. Measure and mark each dimension from end of boards. 3 Secure with (2) 3" nails at each mark. Go to page 15.
LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. BEGIN See page 9 for the preferred floor leveling method. 1 Use level and check the frame is level before applying floor panels. 3 Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square.
10 x 12' FLOOR FRAME (Not Included) x20 3" (7,6 cm) Put both floor sections together and attach as shown using 3" nails. 4 FINISH You have finished your floor frame. Proceed to level and square frame. 5 D O O R (4) Nails per side, stagger pattern. Section 2 Section 1 140-5/8" (357,2 cm) 120" (305 cm) LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed.
10 x 16' FLOOR FRAME (Not Included) x20 3" (7,6 cm) Put both floor sections together and attach as shown using 3" nails. 4 FINISH You have finished your floor frame. Proceed to level and square frame. O O R (4) Nails per side, stagger pattern. Section 2 D 5 Section 1 188-5/8" (479 cm) 120" (305 cm) LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed.
10' x 8' FLOOR PANELS (Not Included) PARTS REQUIRED: x55 48" x 92-5/8" (122 x 235,3 cm) x1 2" (5 cm) FLOOR PANELS NOT INCLUDED. SEE PAGE 8 FOR PANEL SIZES AND QUANTITIES. Ensure your floor frame is square by installing (1) panel and squaring frame. BEGIN Install (1) 48 x 92-5/8" panel with the rough side up (painted-grid lines side) with the 48" edge and corner flush to the floor frame (Fig A). Secure panel with (2) 2" nails in the corners. D O O R 1 2 Move to the opposite end.
10' x 8' FLOOR PANELS (Not Included) PARTS REQUIRED: x1 x95 FLOOR PANELS NOT INCLUDED. SEE PAGE 8 FOR PANEL SIZES AND QUANTITIES. x1 48" x 92-5/8" (122 x 235,3 cm) 2" (5 cm) 5/8 x 23-7/8 x 92-5/8" (1,6 x 61 x 235 cm) Continue installing panels with rough side up (painted grid lines). 6 Use a chalk line or grid lines on panels for 2" nails spaced 6" apart on edges and 12" apart inside panel. .
10' x 12' FLOOR PANELS (Not Included) PARTS REQUIRED: x55 FLOOR PANELS NOT INCLUDED. SEE PAGE 8 FOR PANEL SIZES AND QUANTITIES. 48" x 48" (122 x 122 cm) x1 2" (5 cm) Secure using 2" nails spaced 6" apart on edges and 12" apart inside panel. Use a chalk line or use pre-painted grid lines to nail into joists under panel. O 2 O Install(1) 48" x 48" panel with the rough side up (painted-grid lines side) on Section 2 with the 48" edge and corner flush to the floor frame and Section 1.
10' x 12' FLOOR PANELS (Not Included) PARTS REQUIRED: x1 x95 x1 48" x 48" (122 x 122 cm) 5/8 x 23-7/8 x 48" (1,6 x 61 x 122 cm) 2" (5 cm) FLOOR PANELS NOT INCLUDED. SEE PAGE 8 FOR PANEL SIZES AND QUANTITIES. Continue installing panels with rough side up (painted grid lines) as shown. 4 Use a chalk line or grid lines on panels for 2" nails spaced 6" apart on edges and 12" apart inside panel. . D O O R 3 FINISH You have finished Installing your floor panels. Continue on page 22.
10' x 16' FLOOR PANELS (Not Included) PARTS REQUIRED: x55 48" x 96" (122 x 244 cm) x1 FLOOR PANELS NOT INCLUDED. SEE PAGE 8 FOR PANEL SIZES AND QUANTITIES. 2" (5 cm) BEGIN Position (1) 48" x 96" panel with the rough side up (painted-grid lines side) with the 96" edge and corner flush to the floor frame and Section 1. 2 Secure the panel with 2" nails spaced 6" apart on edges and 12" apart inside panel. Use a chalk line or use pre-painted grid lines to nail into joists under panel.
10' x 16' FLOOR PANELS (Not Included) PARTS REQUIRED: x1 x95 FLOOR PANELS NOT INCLUDED. SEE PAGE 8 FOR PANEL SIZES AND QUANTITIES. x1 5/8 x 48 x 96" (1,6 x 122 x 244 cm) 2" (5 cm) 5/8 x 23-7/8 x 96" (1,6 x 61 x 244 cm) 3 Continue installing panels with rough side up (painted grid lines). 4 Use a chalk line or grid lines on panels to locate frame Secure with 2" nails spaced 6" apart on edges and 12" apart inside panel. O O D Your floor panels are now installed. Continue on page 22.
I M PIMPORTANT! O R TA N T ! Check the floor frame is level after installing floor panels. Re-level if needed. OR DO • The floor should used as a stable work surface for wall construction. HINT: • Organize your assembly procedure during the build process to avoid over-handling of the walls.
RAFTER ASSEMBLY JIG x8 PARTS REQUIRED: x4 GBB ¸1 1-1/4" (3,2 cm) 1 x 3 x 7-1/2" (2,5 x 7,6 x 19 cm) BEGIN Build a Jig to ensure all Rafters are assembled the same. Mark a straight line on the Floor from corner to corner (Fig. A) or on sill plates to fit measurements (Fig. B). 3 Screw blocks in place to measurement shown. D O O R 2 Make sure blocks are square and at 125" (317,5 cm) FINISH You have finished building a Rafter Jig. (2) 1-1/4" (3,2 cm) Screws per block 125' (317.5 cm) Fig.
RAFTERS PARTS REQUIRED: 2" (5 cm) 6 x 24" (15 x 61 cm) x6/x10/x14 x6/x10/x14 x72 CV 2 x 4 x 65-7/8" (5 x 10 x 167 cm) ¸1 BEGIN Flip over rafter assembly and secure gusset to back side of rafter. O 4 O Secure gusset to rafter with 2" nails, staggered, as shown. D 2 R Place (2) rafter halves CV on floor jig. You will assemble (4) rafters. Repeat steps 1-4 to build (2) more assemblies for 10' x 8' Kit, (4) more assemblies for 10' x 12' Kit, or six more assemblies for 10' x 16' Kit.
BACK WALL FRAME PARTS REQUIRED: x1 x6 3" (7,6 cm) NH 2 x 3 x 46-1/4" (5 x 7,6 x 117,5 cm) PB x2 2 x 3 x 77" (5 x 7,6 x 196 cm) x1 PR 2 x 3 x 94-1/2" (5 x 7,6 x 240 cm) BEGIN Orient parts on edge on floor as shown. 2 Secure with (2) 3" nails at each connection.
BACK WALL FRAME x2 PARTS REQUIRED: x1 3" (7,6 cm) NH 2 x 3 x 46-1/4" (5 x 7,6 x 117,5 cm) 3 Arrange parts on edge on floor as shown. D O O R Secure with (2) 3" screws at middle connection. FINISH Your back wall frame is now assembled.
BACK WALL PANELS PARTS REQUIRED: x32 2" (5 cm) 3/8 x 48 x 84" (1 x 122 x 213,4 cm) x1 3/4" GAUGE BLOCK BEGIN Place LEFT panel on back frame as shown with primed side facing up. . O Secure with 2" nails spaced 6" apart on edges and 12" apart inside panel. O R Use a 3/4" gauge block at edges of panel. D 1 Do not nail in groove. 3/4" (1,9 cm) For squareness maintain 3/4" measurement along panel edges.
BACK WALL PANELS PARTS REQUIRED: x32 2" (5 cm) 3/8 x 48 x 84" (1 x 122 x 213,4 cm) x1 2 3/4" GAUGE BLOCK Place RIGHT panel on back frame as shown with primed side facing up. Use a 3/4" gauge block at edges of panel. O R . D O Secure with 2" nails spaced 6" apart on edges and 12" apart inside panel. Do not nail in groove. To draw panels tight at seams angle nail.
WING WALL PANELS PARTS REQUIRED: x32 x2 RIGHT x2 LEFT x4 1-1/4" (3 cm) OY 2 x 3 x 72" (5 x 7,6 x 183 cm) You will assemble (2) RIGHT and (2) LEFT wing walls. BEGIN Place OY on floor. Place a wing wall panel primed side down onto OY (Fig. A) and flush to panel edges as shown. 3 Secure panel flush to edges with (8) 1-1/4 screws spaced 10" apart. 4 You have finished building (2) sets of wing wall assemblies. Set (1) LEFT and (1) RIGHT wing walls aside. Continue building your back wall.
BACK WALL PANELS PARTS REQUIRED: x24 2" (5 cm) Pre-assembled x1 LEFT x1 Pre-assembled RIGHT 5 Place wing wall assemblies on frame with bottom of panels flush. Secure wing wall assemblies to back wall frame with 2" nails spaced 6" apart. D O O R Do not nail in groove. Primed side UP 6" (15,cm) LEFT Primed side UP Flush 6" (15 cm) RIGHT HINT: To draw panels tight at seams angle nail. Flush Use a 2x3" for support. FINISH Your wing walls are now installed.
BACK WALL GABLE PANELS PARTS REQUIRED: x6 GAA 3/4" GAUGE BLOCK x1 RIGHT x1 LEFT 2" (5 cm) x6 BEGIN Place left gable panel onto frame primed side up and flush to left panel. NOTE: Panel grooves will not align. 2 Use a 3/4" gauge block at edge of panel. Secure with 2" nails along edge as shown. D O O R 1 Use a 2x3" for support. Primed side UP 3/4" (1,9 cm) Flush Gauge Block 3 Place right gable panel onto frame primed side up and flush to left panel. NOTE: Panel grooves will not align.
FRONT WALL FRAME PARTS REQUIRED: x6 3" (7,6 cm) LT x1 2 x 3 x 22-1/8" (5 x 7,6 x 56 cm) x2 PB 2 x 3 x 77" (5 x 7,6 x 196 cm) x1 PR 2 x 3 x 94-1/2" (5 x 7,6 x 240 cm) Ensure LT is centered with PR and nail in place with (2) 3" nails. O 2 O Arrange (2) PB, (1) PR and (1) LT on edge on floor. Secure (2) PB to PR with (2) 3" nails at each end.
FRONT WALL PANELS x22 PARTS REQUIRED: 2" (5 cm) x1 3/4" GAUGE BLOCK BEGIN Place LEFT panel on front frame as shown with primed side up. Use a 3/4" gauge block on edges of panel. O O R Secure panel to frame with 2" nails spaced 6" apart. D 1 Do not nail in groove. For squareness, maintain 3/4" measurements along panel edges. 1" (2,5 cm) 3/4" GAUGE BLOCK 3/4" (1,9 cm) 6" (15,2 cm) 3/4" (1,9 cm) 6" Primed Side (15,2 cm) UP 3/4" GAUGE BLOCK 97-1/2" (247,7 cm) 33 3/4" (1,9 cm) 3/4" (1.
FRONT WALL PANELS x22 PARTS REQUIRED: 2" (5 cm) 3/4" GAUGE BLOCK x1 Place RIGHT panel on front frame primed side up. Use a 3/4" gauge block on edges of panel. O O R Secure panel to frame with 2" nails spaced 6" apart. D 2 Do not nail in groove. To draw panels tight at seams angle nail. Primed Side UP Panels Flush 3/4" (1,9 cm) Gauge Block 6" (15,2 cm) 97-1/2" (247,7 cm) 3/4" (1,9 cm) 1" (2,5 cm) For squareness, maintain 3/4" and 97-1/2" measurements.
FRONT WALL PANELS PARTS REQUIRED: x24 2" (5 cm) Pre-assembled x1 LEFT x1 Pre-assembled RIGHT Primed Side UP 6" (15,2 cm) 6" (15,2 cm) Flush To draw panels tight at seams angle nail. Flush Use a 2x3" for support. FINISH Your front wall is now assembled. 35 O O Do not nail in groove. R Place wing wall panels onto frame with bottom of panels flush. Secure wing wall assemblies with 2" nails spaced 6" apart.
SIDE WALL FRAMES PARTS REQUIRED: x14 3" (7,6 cm) x4 7/16 x 2-1/2 x 24-3/4" (1,1 x 6,4 x 62,9 cm) x6 OV 2 x 3 x 69" (5 x 7,6 x 175 cm) x2 PM 2 x 3 x 92-5/8" (5 x 7,6 x 235,3 cm) IMPORTANT! You will build (2) identical walls. BEGIN If building 10' x 12' kit, go to page 38. If building 10' x 16' kit, go to page 42. 2 If building 10' x 8' kit orient parts on edge on floor. Measure and mark from end of boards. Secure with (2) 3" nails at each mark.
10' x 8' SIDE WALL FRAME- SOFFIT PARTS REQUIRED: x22 1-1/4" (3,2 cm) x2 3/8 x 5 x 93-1/4" (0,9 x 12,7 x 236,9 cm) 4 Place panel on 2 x 3 with primed side against 2 x 3 (Fig A) Keep panel flush along entire edge of 2 x 3 top plate (Fig A). Install soffit panel flush to 2 x 3 (Fig. A) and with a 3/8" offset at ends (Fig. B, C). R 5 D O O Secure with (11) 1-1/4" screws. 9-1/2" (24 cm) 3/8" (10 mm) Fig. B 3/8" (10 mm) 93-1/4" (236,9 cm) Fig. C PRIMED SIDE Flush Fig.
10' x 8' SIDE WALL PANELS PARTS REQUIRED: x58 3/4" GAUGE BLOCK x2 3/8 x 48 x 72" (1 x 122 x 183 cm) 6 2" (5 cm) Ensure your wall frame is square by installing (1) panel and squaring frame. Place (1) 48 x 72" panel onto wall frame with primed side up as shown. Note the lip and square edges. 7 D O O R Use the gauge block to mark the 3/4" measurement on the wall stud. Locate the panel flush under the soffit panel. Secure panel with (2) 2" nails in the corners (Fig. A). Move to the opposite end.
10' x 8' SIDE WALL PANELS PARTS REQUIRED: 2" (5 cm) 3/8" x 48" x 72" (1 x 122 x 183 cm) x2 Place 48" panel on frame as shown with primed side facing up. NOTE THE SQUARE AND LIP EDGES. Secure panel with 2" nails spaced 6" apart on edges and 12" apart inside panel. Flush O O R Do not nail in groove. D 8 x58 To draw panels tight at seams angle nail. 12" (30 cm) 6" (15 cm) 48" (122 cm) LIP EDGE SQUARE EDGE D O O R Carefully flip your side wall over.
10' x 12' SIDE WALL FRAMES PARTS REQUIRED: x28 x4 3" (7,6 cm) x2 7/16 x 2-1/2 x 24-3/4" (1,1 x 6,4 x 62,9 cm) x6 7/16 x 2-1/2 x 48 (1,1 x 6,4 x 122 cm) x2 OV 2 x 3 x 69" (5 x 7,6 x 175 cm) x2 NK 2 x 3 x 48" (5 x 7,6 x 122 cm) PM 2 x 3 x 92-5/8" (5 x 7,6 x 235,3 cm) BEGIN 1 If building 10' x 16' kit, go to page 42. 2 If building 10' x 12' kit, arrange parts on edge on floor. Measure and mark from end of boards. D O O R IMPORTANT! You will build (2) walls the same.
10' x 12' SIDE WALL FRAME- SOFFIT PARTS REQUIRED: x32 1-1/4" (3,2 cm) x2 3/8 x 5 x 48" (0,9 x 12,7 x 122 cm) x2 3/8 x 5 x 93-1/4" (0,9 x 12,7 x 236,9 cm) 3 Place panels onto 2 x 3 with primed side against 2 x 3 as shown (Fig A) Keep panel flush along entire edge of 2 x 3 top plate (Fig A). R Install soffit panels flush to 2 x 3 (Fig A) and with 3/8" offset at ends (Fig. B, C). Secure with(14) 1-1/4" screws. D O O 4 3/8" (10 mm) Fig.
10' x 12' SIDE WALL PANELS PARTS REQUIRED: x58 2" (5 cm) 3/4" GAUGE BLOCK x2 3/8 x 48 x 72" (1 x 122 x 183 cm) Ensure your wall frame is square by installing (1) panel and squaring frame. 6 Install (1) 48" x 72" panel onto wall frame with primed side up as shown. Note the lip and square edges. D O O R Use the gauge block to mark the 3/4" measurement on the wall stud. Locate the panel flush under the soffit panel. Secure panel with (2) 2" nails in the corners (Fig. A).
10' x 12' SIDE WALL PANELS PARTS REQUIRED: 2" (5 cm) 3/8" x 48" x 72" (1 x 122 x 183 cm) x4 9 x148 Place(2) 48"x 72" panels flush to installed panels, as shown. NOTE THE SQUARE AND LIP EDGES. D O O R Secure with 2" nails spaced 6" apart on edges and 12" apart inside panel. Do not nail in groove. Flush To draw panels tight at seams angle nail. 12" (30 cm) 6" (15 cm) 48" (122 cm) LIP EDGE D O O R SQUARE EDGE Carefully flip your side wall over.
10' x 16' SIDE WALL FRAMES PARTS REQUIRED: x84 x4 3" (7,6 cm) x4 7/16 x 2-1/2 x 24-3/4" (1,1 x 6,4 x 62,9 cm) x6 7/16 x 2-1/2 x 48" (1,1 x 6,4 x 122 cm) x2 OV 2 x 3 x 69" (5 x 7,6 x 175 cm) x2 NK 2 x 3 x 48" (5 x 7,6 x 122 cm) PM 2 x 3 x 92-5/8" (5 x 7,6 x 235,3 cm) BEGIN 1 Measure and mark from end of boards. IMPORTANT! You will build (2) walls the same. D O O R Secure with (2) 3" nails at each mark.
10' x 16' SIDE WALL FRAME- SOFFIT PARTS REQUIRED: x38 1-1/4" (3,2 cm) x4 3/8 x 5 x 48" (0,9 x 12,7 x 122 cm) x2 3/8 x 5 x 93-1/4" (0,9 x 12,7 x 236,9 cm) 2 Place panels onto 2 x 3 with primed side against 2 x 3 as shown (Fig A) Keep panel flush along entire edge of 2 x 3 top plate (Fig A). O R Install soffit panels flush to 2 x 3 (Fig A) and with 3/8" offset at ends (Fig. B, C). Secure with (19) 1-1/4" screws. D O 3 Fig.
10' x 16' SIDE WALL PANELS PARTS REQUIRED: x58 2" (5 cm) 3/4" GAUGE BLOCK x2 3/8 x 48 x 72" (1 x 122 x 183 cm) Ensure your wall frame is square by installing (1) panel and squaring frame. 4 Place the 48 x 72" panel onto wall frame with primed side up. Note the lip and square edges. D O O R Use the gauge block to mark the 3/4" measurement on the wall stud. Locate the panel flush under the soffit panel. Secure panel with (2) 2" nails in the corners (Fig. A). 5 Move to the opposite end.
10' x 16 ' SIDE WALL PANELS PARTS REQUIRED: 2" (5 cm) 3/8" x 48" x 72" (1 x 122 x 183 cm) x6 6 x238 Place additional 48"x72" panels on frame flush to installed panels. NOTE THE SQUARE AND LIP EDGES. Do not nail in groove. D O O R Secure panels with 2" nails spaced 6" apart on edges and 12" apart inside panel. To draw panels tight at seams angle nail. Flush 12" (30 cm) 6" (15 cm) 48" (122 cm) LIP EDGE 48" (122 cm) SQUARE EDGE D O O R 48" (122 cm) Carefully flip your side wall over.
BACK WALL INSTALLATION PARTS REQUIRED (TEMPORARY): x1 x8 3" (7,6 cm) OO x24 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) 2" (5 cm) BEGIN Center back wall assembly on the 120" (305 cm) floor dimension. 2 Use OO as a temporary brace. Secure with (2) 3" screws. D O O R 1 ) 05 cm 3" (7,6 cm) Screws 120" (3 3 Secure lower edge of panel to floor frame with 2" nails spaced 6" apart. Angle nail to hit floor frame (Fig. A). 4 Secure back wall uprights to floor with (2) 3" screws (Fig. B).
SIDE WALLS INSTALLATION x4/8/12 x30/39/48 x2 3" (7,6 cm) 3" (7,6 cm) 2" (5 cm) Additional fasteners needed for 10' x 12' kit or 10' x 16' kit. Same instructions apply. BEGIN D O O R Stand right side wall on floor. It is important to secure the side wall in the following order: 1 Soffit Panel Center side wall on floor front to back. Nail the lower side wall corner to the back wall trim with (1) 2" nail (Fig. A).
FRONT WALL INSTALLATION x8 3" (7,6 cm) 2" (5 cm) Center front wall on floor side-to-side. Soffit Panel The side wall soffit will overlap the front wall 3/8" (Fig. A). Panel 3/8" (0,9 cm) OVERLAP D O 1 R BEGIN O x36 Trim Fig. A Nail the front wall flush to the floor using 2" nails spaced 6" apart. Angle nails to hit floor frame (Fig. B). Nail the lower side wall corner to the front wall trim with (1) 2" nail (Fig. C). 2" (5 cm) Nail Fig.
GABLE TRIM x24 PARTS REQUIRED: x4 1-1/4" (3 cm) CDD 2 x 3 x 58" (5 x 7,6 x 147,3 cm) ¸1 BEGIN O O R Install 2nd CDD flush to panel edge and flush to installed CDD (Fig. A). Secure trim with (8) 1-1/4" screws from inside. Install (2) screws at seam (Fig. B). D 2 Position (1) CDD flush to front panel edge and center on right edge of groove (Fig. A). Install trim with (8) 1-1/4" screws from inside. Install (2) screws at seam (Fig. B). Repeat steps to attach the back trim.
BACK WALL GABLE TRIM PARTS REQUIRED: 3/4" (1,9 cm) x11 x1 XMA 11/16 x 2-1/2 x 60-5/8" (1,7 x 6,3 x 154 cm) ¸1 BEGIN D O O R Clamp or hold trim XMA onto gable panel seam and up against gable trim. Ensure XMA is level. GABLE TRIM SEAM XMA Flush 2 LEVEL Flush From the inside, fasten XMA with 3/4" screws, in the pattern shown. (11) 3/4" (1,9 cm) XMA Screws 2-1/2" (6,3 cm) 1-1/4" (3,2 cm) IN S ID E FINISH Your back wall gable trim is now installed.
TRIM / ENDCAPS x14 PARTS REQUIRED: x4 1-1/4" (3,2 cm) GBB x4 ¸1 1 x 3 x 7-1/2" (2,5 x 7,6 x 19 cm) RIGHT PAINTED RED 3/4 x 5-1/8 x 8-3/8" (1,9 x 13 x 21,3 cm) LEFT PAINTED GREEN BEGIN Assemble GBB to endcaps with 1-1/4" screws, as shown. Repeat steps to build (2) more endcaps. GBB D O O R Flush GBB Flush Right - RED x2 2 Flush Left - GREEN x2 Flush Locate endcaps flush with upper trim and corner trim. Secure each endcap from inside of shed with (4) 1-1/4" screws, as shown (Fig. A).
RAFTERS x12 PARTS REQUIRED: 3" (7,6 cm) x6 pre-assembled 2" (5 cm) x3 Repeat steps to install (3) additional rafters. FINISH Your rafters are now installed. Fig. B Screw into top plate. Fig.A 2" (5 cm) Screw 1" (2,5 cm) Flush NOTE: Measurements from inside of panels 22-1/4" (56,5 cm) 24" (61 cm) 24" (61 cm) Align over studs. Maintain the measurements between rafters. 54 22-1/4" (56,5 cm) R Secure with (2) 3" screws at each end (Fig. B). Re-tighten 2" screws if neccessary.
ROOF PANELS PARTS REQUIRED: x4 2" (5 cm) x2 7/16 x 48 x 96" (1,1 x 122 x 244 cm) Roof panels may cause serious injury until securely fastened. D O O R You must square the roof by attaching (1) panel fist. You will use the panels’ long edge as a lever to bring your roof into square. Commonly known as “racking”. BEGIN 1 Install (1) 48 x 96" panel with the rough side up (painted-grid lines side) with a 1/8" measurement on the rafter (Fig A) and the panel flush at the peak (Fig. B). Flush at peak.
ROOF PANELS PARTS REQUIRED: 3 2" (5 cm) 7/16 x 19 x 48" (1,1 x 48 x 122 cm) Keep spacing between the center of the rafters at the lower edge of the panel and secure with (1) 2" nail into each rafter (Fig. E). R x4 x104 22-1/4" (56,5 cm) 24" (61 cm) 24" (61 cm) D O O NOTE: Measurements from inside of panels Move to the top of the panel and keep spacing between the center of the rafters. Secure with (1) 2" nail into each rafter (Fig. E).
TRIM x20 PARTS REQUIRED: x2 2" (5 cm) HS 1 x 3 x 94-3/4" (2,5 x 7,6 x 240,6 cm) ¸1 BEGIN D O O R Install fascia trim flush under roof panel (Fig. A) and endcaps at ends of rafters (Fig. B). Secure with 2" nails, as shown. Repeat steps to install fascia trim on both sides. Fig. B HS Flush HS Flush Fig. A FINISH Your fascia trim boards are now installed.
DOORS PARTS REQUIRED: x1 x2 OO 1-1/4" (3 cm) 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) x2 HINT: Look for 3/8" SPACER attached to doors. x1 x1 Left Door x1 Right Door 2" (5 cm) x4 3" (7,6 cm) ZJ 5/8 x 3 x 72" (1,6 x 7,6 x 183 cm) Orient parts as shown on flat surface. 3/8" offset is to top. Look for red (right) and green (left) on hinge board. 2 Fasten temporary support OO with 3" screws in middle and at ends. Tighten securely.
DOORS x6 PARTS REQUIRED: x1 3" (7,6 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) Install temporary support OO as a ledger board flush under wall panels with (2) 3" screws (Fig. A). D O O R 3 OO Fig. A Flush against wall panels. OO 4 Center doors on right edge of groove as shown (Fig. B). Check ledger board is still flush under panels. 5 Screw hinge boards into wall supports and floor using (4) 3" screws as shown. Ensure screws penetrate into framing and floor (Fig. C, D).
DOOR PARTS REQUIRED: x1 2" (5 cm) x8 ZJ 3/4" (1,9 cm) x52 5/8 x 3 x 72" (1,6 x 7,6 x 183 cm) x1 64" Metal Threshold 1 Secure hinge boards from inside using 3/4" screws as shown (Fig. A). 2 Reinforce the door trim using 3/4" screws through door panel into trim (Fig. A). Locate screws as shown in Fig. B. Secure with (2) screws at seams. Center trim ZJ over doors and secure using (8) 2" finish nails into framing as shown.
DOOR WEATHERSTRIP PARTS REQUIRED: x2 x14 2" (5 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) 2 Secure OO with (7) 3" screws through outside trim into OO (Fig. B) 3 On right door center OO vertically in door opening (Fig. A). OO will offset the right door 1" IN from the door trim (Fig. C). 4 Secure OO with (7) 3" screws through outside trim into OO (Fig. C). O With left door closed, center a weatherstrip OO vertically on the left door in the door opening (Fig. A).
DOOR HARDWARE PARTS REQUIRED: x1 x4 x1 3/8" (9 mm) Drill Bit x7 3/4" (1,9 cm) 3/4" (1,9 cm) BEGIN Install barrel bolt flush at top of OO on left door. Secure with 3/4" screws as shown (Fig A). 2 With door closed mark hole location for bolt to extend into. HINT: Extend bolt to leave a mark in wood. Tap bolt with hammer. Drill 3/8" hole deep enough for bolt to slide into. 3 Install hasp on right door and latch on left door. Bottom edge of hasp is 35-1/2" (90 cm) up from bottom edge of door trim.
x16 PARTS REQUIRED: DOOR TRIM ZZ x8 3/4" (19 mm) 5/8 x 3 x 14" (1,6 x 7,6 x 35,5 cm) PARTS REQUIRED: x18 3/4" (1,9 cm) WNA BEGIN x8 1 5/8 xPosition 4 x 14" (1,6 x 10 xon 35,6 cm) pane of Door Panel, as shown. parts lower 2 Attach each using two 3/4" (19 mm) screws as shown. D O O R FINISH 3BEGINYou have finished attaching your door trim. Install WNA on lower section of door panel. 1 Secure from inside with 3/4" screws as shown. ZZ WNA FINISH Your door trim is now installed.
PAINT & CAULK - NOT INCLUDED - • Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. • Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: • Bottom edge of all siding and trim • Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting.
SHINGLES - NOT INCLUDED • Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch Notch SHINGLE NAIL PATTERN 1" (2,5cm) 1/2" (1,3cm) Sealing Str ip 1" (2,5cm) Half A Rain Slot Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. BEGIN 1 Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.
SHINGLES continued... 2 2 Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge. Roof Deck FRONT OF SHED 1" (2,5 cm) BACK OF SHED Flush with starter row. Notch - or Drip Edge Flush with starter row. Notch 3 Install second row of shingles flush at top of first row's rain slots. Ensure 1" overhang or flush to drip edge at front, stagger each row. FRONT OF SHED BACK OF SHED 1" (2,5 cm) Notch Flush with rain slots.
SHINGLES continued... 5 Continue installing rows of shingles to the peak. At the peak make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at ridge cut to peak with a utility knife. Cut Off. 5" (12,7 cm) MAX. CUT Top of rain slot. 5" (12,7 cm) MAX. • If more than 5" to rain slot you must install another row of shingles. 6 Repeat steps 1 - 7 to shingle the opposite side of your roof. Trim shingles at ridge.
SHINGLES - RIDGE CAP • You will finish off the top of the roof with a ridge cap made from shingles. BEGIN 1 Cut shingles into (3) pieces. Hint: Use cut-off pieces first. 2" (5 cm) 2" (5 cm) 2" (5 cm) 2" (5 cm 2" (5 cm) 2" (5 cm) Score shingle, then snap-off angled cut. Weather Seal Top of slot. Note: • You will need about 20 - 22 cut pieces. 2 20 to 22 Pieces Install first ridge cap flush to shingles at front, as shown. (1) Nail per side through weather seal.
SHINGLES - RIDGE CAP continued... 4 Continue installing ridge cap to back of roof. 5 Make sure there is 4" between the shingle-color and edge of shingles. 4" (10 cm) 6 Trim cap off flush to shingles When you have 4" minimum of shingle color cut (1) piece to cap your roof. Cut at top of rain slot. Cap 7 Install flush to shingles. Flush to shingles (2) Nails per side. FINISH 8 You have finished your ridge cap.
LIMITED CONDITIONAL WARRANTY* Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for 1 year. 2. All accessories, hardware and metal components are warranted for 2 years. 3. All Oriented Strand Board (OSB) is warranted for 2 years 4. Siding and Trim is warranted for 10 years. 5. Solar Shed windows are warranted for 1 year. 6. Cedar lumber is warranted for 15 years. 7. Preserved Pine is warranted for 10 years. 8.
