Instructions / Assembly

ManualsBrandsHandy Home Products ManualsKitchen8 ft. x 10 ft. Wide Building Cupola

Handy Checklist & Assembly Instructions

CUPOLA

— BEFORE YOU BEGIN —



First…

Read these instructions thoroughly before you begin

assembly. Assembly is easiest if you follow the

steps in the order shown.

In a drawing, a dotted line represents a part hidden

from view (like a part under a panel).

Lumber is graded from only one side. Check the

part for the most attractive face and make sure to

face it to the outside.



Check all parts

Compare the parts you have to the list on this page.

If a part is missing, circle the part in question and

call us toll-free at 1-800-437-0784.



Squareness is Very Important!

Keeping all 90 corners and 90 perpendiculars

square throughout the assembly of this kit will make

each succeeding step easier and is necessary to

assure that all components fit together properly.



Always wear OSHA-approved

safety glasses throughout the assembly

process

■

Tools Required

 Hammer

 Key Hole Saw

 Phillips Screwdriver

 Step ladder

 Pencil

 Tape measure

■

Optional Tools

 Electric Drill with #2 Phillips Tip

 Sabre Saw

 Square

 Nail Pouch

Cupola shown with optional Weathervane

I.D. Use/Description Size (in) Size ( cm) Qty

Parts List

 (A)SIDE PANELS.....3/8 x 11-3/4” x 19-1/8”.30.5 x 48.6 cm ...... 2

 (D)SIDE PANELS(to be cut)..3/8 x 11-3/4” x 20”. 30.5 x 50 cm. 2

 (AC)INTERIOR CORNER SUP.1-1/2” x 2-1/2” x 10” .26 cm. ...... 4

 (BB)CORNER TRIM .......... 3/4”x 1-1/2” x 10-1/2”.27 cm .......... 8

 (BP)TOP TRIM ................... 3/4”x 1-1/2” x 20-3/4”.52 cm .......... 4

 (--) LONG ROOF SUPPORT..3/4 x 5-1/4” x 23-3/4”.14 x 61 cm . 1

 (--) SHORT ROOF SUPPORTS..3/4 x 5” x 11-5/8”. 13 x 30 cm .. 2

 (--) ROOF PANELS...3/8 x 12” x 21-1/2” ....... 30.5 x 55 cm ....... 4

 (--) HARDWARE KIT ..................................................................... 1

(INCLUDES 1-1/2” & 2” FINISH NAILS, 3” SCREWS, 1” SCREWS)

 (--) CUTTING TEMPLATE ............................................................. 1

Toll-Free 1-800-437-0784

Made in the U.S.A

06/15/06

#16612

Summary of content (4 pages)

PAGE 1
#16612 CUPOLA 06/15/06 Made in the U.S.A Toll-Free 1-800-437-0784 Handy Checklist & Assembly Instructions — BEFORE YOU BEGIN — First… Read these instructions thoroughly before you begin assembly. Assembly is easiest if you follow the steps in the order shown. In a drawing, a dotted line represents a part hidden from view (like a part under a panel). Lumber is graded from only one side. Check the part for the most attractive face and make sure to face it to the outside. I.D.
PAGE 2
A. Position Side Panel 11-3/4” x 19-1/8” (A) on top of two Interior Corner Supports 1-1/2” x 2-1/2” x 10” (AC) with supports flush to sides and top of Panel and Panel siding facing up. Secure with six 1-1/2” finish nails (C) through Panel into supports. C CUPOLA CUTTING TEMPLATE PREMIER SERIES HERITAGE SERIES SIGNATURE SERIES Repeat other Side Panel 11-3/4” x 19-1/8” (A) and two Interior Corner Supports 1-1/2” x 2-1/2” x 10” (AC).
PAGE 3
E. Mark Template and cut out with a Key Hole Saw or a Sabre Saw as shown in step E. Be sure Corner Trim (BB) is flush to bottom of Panel where it is to be cut. Cut out other 11-3/4” x 20” Panel with Corner Trim (BB) attached in the same manner. G KEY HOLE SAW E D Panel siding down 1-1/2" Finish nails BB BB G. Position un-cut Corner Trim 3/4” x 1-1/2” x 10-1/2” (BB) over corner of Panels flush to front of Corner Trim (E).
PAGE 4
L. Position four assembled Roof Panels (M) on top of Top Trim (BP) and secure with twelve 1-1/2” Finish nails (C) through Panels into all four Top Trim pieces (BP). I. Position Long Roof Support 3/4” x 5-1/4” x 23-3/4” (K) and Short Roof Support 3/4” x 5” x 11-5/8” (L) as shown and connect with two 1-1/2” Finish nails (C). L I 1-1/2" Finish nails C K Flush at bottom L M J.