Instructions / Assembly

ManualsBrandsHandy Home Products ManualsKitchenMonterey 12 ft. x 16 ft. Gazebo Floor Kit

■■

■ Tools required

❑ Hammer

❑ #2 Phillips Screwdriver

❑ Level

❑ Tape Measure

❑ Pencil

■■

■ Optional tools

❑ Electric Drill w/ #2 Phillips Tip

❑ Nail Pouch

Revision: 2-26-03

Run:

- BEFORE YOU BEGIN -

Made in the U.S.A.

- TREATING YOUR GAZEBO -

■■

■ Staining...

These Gazebo Floor Panels are constructed of a long-

lasting western cedar. Untreated Cedar exposed to

sunlight will eventually weather to a silver-grey color. To

help keep original red color, apply a minimum of two

coats of oil based penetrating stain WITHIN 30 DAYS

(required by warranty).

Always wear OSHA-APPROVED safety

glasses throughout assembly process

■■

■ First...

Read these instructions thoroughly before you begin

assembly. Assembly is easiest if you follow the steps

in the order shown.

In a drawing, a dotted line represents a part hidden

from view (like a part under a panel).

■■

■ Check all parts

Compare parts you have to the list on page 2. If a part

is missing, circle the part in question in the parts list

and call us toll-free at 1-800-437-0784.

■■

■ Preparation required

We recommend that you assemble this floor on level

ground in the location it will be used. Assistance is

necessary to handle, fit, and secure some

components. Two people are needed for some steps.

■■

■ Check local zoning

Before starting construction, check with your local

building code official for any required permits,

variances, etc.

#16690

10’x14’ - 10 sided Gazebo Floor

12’x16’ - 12 sided Gazebo Floor (not shown)

14’x18’ - 14 sided Gazebo Floor (not shown)

10’, 12’ &14’ Oval

Gazebo Floor

STAIN REQUIREMENTS FOR GAZEBO FLOORS

FLOOR SIZE # OF GALLONS

10' 1

12' 1

14' 1-1/2"

Summary of content (8 pages)

PAGE 1
Revision: Run: 10’, 12’ &14’ Oval Gazebo Floor 2-26-03 Made in the U.S.A. - BEFORE YOU BEGIN Always wear OSHA-APPROVED safety glasses throughout assembly process ■ First... Read these instructions thoroughly before you begin assembly. Assembly is easiest if you follow the steps in the order shown. In a drawing, a dotted line represents a part hidden from view (like a part under a panel). ■ Check all parts Compare parts you have to the list on page 2.
PAGE 2
10’, 12’ & 14’ Oval Gazebo Floor ■ Parts List 10’ Gazebo Floor Kit ❑ 8 pcs. ❑ 2 pcs. ❑ 12 pcs. ❑ 2 pcs. ❑ 2 pcs. ❑ 3 pcs. ❑ 4 pcs. ❑ 2 pcs. ❑ 1 pc. ❑ 2 pc. ❑ 1 pc. ❑ 8 pcs. ❑ 2 pcs.
PAGE 3
PARTS LIST 10’ FLOOR KIT 1 FLOOR SYSTEM CENTER ASSEMBLY ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs. ❑ 1 pc. Center Floor Support Center Spacer J3’s Solid Center Block Base Plate Treated (if needed) 2 x 6 x 59-1/2” PARTS LIST 14’ FLOOR KIT ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs. ❑ 1 pc. Center Floor Support Center Spacer J3’s Hollow Center Block Base Plate Treated (if needed) 2 x 4 x 42-13/16” 2 x 6 x 4-1/4” 2 x 6 x 59-1/2” PARTS LIST 12’ FLOOR KIT ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs. ❑ 1 pc.
PAGE 4
1 PARTS LIST J1’s 10’Treated FLOOR KIT ❑ 8 pcs. - angled FLOOR SYSTEM FRAMING ❑ 2 pcs. x 44-3/4” ❑ 12 pcs. ❑ 1 pc. NOTE: Assembly shown below is for 10’ Oval ❑ 2 pcs. 44-3/4” ❑ 14 pcs. ❑ 1 pc. J1A’s Treated J2 2 x 6 x 44-3/4” 2x4x 2 x 6 x 81-1/16” J2’s Treated Center Assembly Connect 12' & 14' Top View with 3" screws. J3 J3 J2 Fig.4 Fig.3 Fig.5 Fig.2 Connect with (1) 3" screw down inside with 6" Phillips Bit.
PAGE 5
1 FLOOR SYSTEM FRAMING CONTINUED PARTS LIST J410’ FLOOR KIT ❑ 4 pcs. ’s Treated Add on 1 x 4 x 54-3/4” PARTS LIST J412’ FLOOR KIT ❑ 4 pcs. ’s Treated Add on 1 x 4 x 67-7/8” PARTS LIST J414’ FLOOR KIT ❑ 4 pcs. ’s Treated Add on 1 x 4 x 81-1/16” 1-C: Install the J4’s on the side of the Joist and flush to top of floor frame with (10) 1-5/8” screws as shown. Install the remaining 3 in same manner for the center floor panel to rest on.
PAGE 6
1 PARTS LIST Triangle 10’ FLOOR KIT ❑ 8 pcs. Deck Panels FLOOR SYSTEM DECKING ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs. Square Center Deck Panels Center Deck Pieces Outside Floor Board 1 x 6 x 44-3/4” PARTS LIST Triangle 12’ FLOOR KIT ❑ 10 pcs. Deck Panels ❑ 2 pcs. ❑ 2 pcs. ❑ 2 pcs. Square Center Deck Panels Center Deck Pieces Outside Floor Board 1 x 6 x 44-3/4” PARTS LIST Triangle 14’ FLOOR KIT ❑ 12 pcs. Deck Panels Note: Layout All Decking Parts before attaching to frame. ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs.
PAGE 7
1 FLOOR SYSTEM DECKING 1-F: Once all floor parts are in place, keep overhang on the frame the same all around your gazebo. 1-F Keep equal overhang all around Floor Frame 1-G: Removal of Center Panels may be necessary for easier assembly. Triangular Floor Panels are attached by using eight 2-1/2” screws only. Add additional screws where holes are predrilled for 12’ and 14’ floor. Predrilled holes are provided in each Floor Panel.
PAGE 8
1 FLOOR SYSTEM DECKING CONTINUED 1-H: Square Floor Panels are attached by using 2-1/2” screws. Keep the panel flush to the Triangular panels short end. Predrilled holes are provided in each Floor Panel. Attach Outside Floor Board flush to the outside of the Triangle Floor Panels with (5) 2-1/2” screws. Flush to Front 1-H Use 2-1/2" Screws Flush to Outside 2-1/2" Screws at Angle 1-I: Attach Center Deck Boards with 2-1/2” screws through predrilled holes. Keep equally spaced.