Instructions / Assembly

ManualsBrandsHandy Home Products ManualsKitchenMonterey 10 ft. x 14 ft. 2-Tier Roof

Oval Gazebo

Second Tier

Parts List

10’ Two Tier Parts

❑ 8 pcs. Pre-assembled Wall Panels

❑ 2 pcs. Pre-assembled Long Wall Panels

❑ 2 pcs. Ridge Block 8-Sided

❑ 1 pc. Metal Roof Cap from Gazebo

❑ 8 pcs. Triangular Roof Panels

❑ 2 pcs. Square Roof Panels

❑ 6 pcs. Plywood Gusset Brackets

❑ 4 pcs. 2 left/2 right Plywood Gusset Brackets

❑12 pcs. Rafters 2 x 4 x 27”

❑ 2 pcs. Center Rafter Support 2 x 4 x 43-1/4” angled

❑ 3 pcs. Rafter Support Spacers 1/2” x 3-1/2” x 6”

❑ 8 pcs. Fascia 2-1/2x21-1/16”

❑ 2 pcs. Fascia 2-1/2x44-3/4”

❑ 10 pcs. Fascia Trim 3/4” x 1-1/2” x 2-3/4”

❑ 2 pcs. Roof Finial Block 1-1/2” x 1-1/2” x 3-1/2”

❑ 2 pcs. Roof Finials from Gazebo

❑ 1 pc. 13” Roll of screen

❑ Hardware #8 - 3” Screw, #8 - 1-5/8” Screw, 6d-2” Nail,

4d-1-1/2” Finish Nail, 3/4” Roofing Nail, 1” Roofing Nail

12’ Two Tier Parts

-BEFORE YOU BEGIN-

■ First...

Read these instructions thoroughly before you begin assembly.

Assembly is easiest if you follow the steps in the order shown.

In a drawing, a dotted line represents a part hidden from view

(like a part under a panel).

Lumber is graded from only one side. Check the part for the

most attractive face and make sure to face it to the outside.

■ Check all parts

Compare the parts you have to the list, If a part is missing, circle

the part in question and call our toll-free # at

(800) 437-0784

Always wear OSHA-APPROVED safety

glasses throughout the assembly process

■ Tools Required

❒

Hammer

❒

Phillips Screwdriver

❒

Level

❒

Pencil

❒

Tape Measure

❒

Staple Gun with 1/4” or 3/8” staples

2-26-03

#16686

■

Optional Tools

❒

Electric Drill with #2 phillips Tip

❒

Square

❒

Nail Pouch

❒

1/8” Drill Bit for Pre-drilling

❑ 10 pcs. Pre-assembled Wall Panels

❑ 2 pcs. Pre-assembled Long Wall Panels

❑ 2 pcs. Hollow Ridge Block 10-Sided

❑ 2 pcs. Ridge Cap 10-Sided

❑ 1 pc. Metal Roof Cap from Gazebo

❑ 10 pcs. Triangular Roof Panels

❑ 2 pcs. Square Roof Panels

❑ 2 pcs. Plywood Gusset Brackets

❑ 4 pcs. 2 left/2 right Plywood Gusset Brackets

❑14 pcs. Rafters 2 x 4 x 33-1/8”

❑ 2 pcs. Center Rafter Support 2 x 4 x 43-1/16” angled

❑ 3 pcs. Rafter Support Spacers 2 x 4 x 2-1/4”

❑10 pcs. Fascia 2-1/2 x 20-9/16”

❑ 2 pcs. Fascia 2-1/2 x 44-3/4”

❑12 pcs. Fascia Trim 3/4” x 1-1/2” x 2-3/4”

❑ 2 pcs. Roof Finial Block 1-1/2” x 2-1/2” x 3-1/2”

❑ 2 pcs. Roof Finials from Gazebo

❑ 1 pc. 13” Roll of screen

❑ Hardware #8 - 3” Screw, #8 - 1-5/8” Screw, 6d-2” Nail,

4d-1-1/2” Finish Nail, 3/4” Roofing Nail, 1” Roofing Nail

14’ Two Tier Parts

❑ 12 pcs. Pre-assembled Wall Panels

❑ 2 pcs. Pre-assembled Long Wall Panels

❑ 2 pc. Ridge Cap 12-Sided

❑ 2 pc. Hollow Ridge Block 12-Sided

❑ 1 pc. Metal Roof Cap from Gazebo

❑ 12 pcs. Triangular Roof Panels

❑ 2 pcs. Square Roof Panels

❑ 2 pcs. Plywood Gusset Brackets

❑ 4 pcs. 2 left/2 right Plywood Gusset Brackets

❑ 16 pcs. Rafters 2 x 4 x 38-5/8”

❑ 2 pcs. Center Rafter Support 2 x 4 x 42-13/16” angled

❑ 3 pcs. Rafter Support Spacers 2 x 4 x 4-1/4”

❑ 12 pcs. Fascia 2-1/2 x 20-3/16”

❑ 2 pcs. Fascia 2-1/2 x 44-3/4”

❑ 14 pcs. Fascia Trim 3/4” x 1-1/2” x 2-3/4”

❑ 2 pcs. Roof Finial Block 1-1/2” x 2-1/2” x 3-1/2”

❑ 2 pcs. Roof Finials from Gazebo

❑ 1 pc. 13” Roll of screen

❑ Hardware #8 - 3” Screw, #8 - 1-5/8” Screw, 6d-2” Nail,

4d-1-1/2” Finish Nail, 3/4” Roofing Nail, 1” Roofing Nail

10’ Oval Second Tier - 10 sided Gazebo shown with Second Tier

12’ Oval Second Tier - 12 sided (not shown)

14’ Oval Second Tier- 14 sided (not shown)

Qty. Description Size

Summary of content (8 pages)

PAGE 1
#16686 2-26-03 Oval Gazebo Second Tier -BEFORE YOU BEGIN- ■ First... Read these instructions thoroughly before you begin assembly. Assembly is easiest if you follow the steps in the order shown. In a drawing, a dotted line represents a part hidden from view (like a part under a panel). Lumber is graded from only one side. Check the part for the most attractive face and make sure to face it to the outside.
PAGE 2
1 SECOND TIER SCREEN AND WALL ASSEMBLY PARTS LIST 10’ GAZEBO PARTS LIST 12’ GAZEBO PARTS LIST 14’ GAZEBO ❑ 8 pcs. ❑ 2 pcs. ❑ 1 pc. ❑ 6 pcs. ❑ 4 pcs. ❑ 10 pcs. ❑ 2 pcs. ❑ 1 pc. ❑ 2 pcs. ❑ 4 pcs. ❑ 12 pcs. ❑ 2 pcs. ❑ 1 pc. ❑ 2 pcs. ❑ 4 pcs.
PAGE 3
2 PARTS LIST 10’ GAZEBO SECOND TIER RIDGE ASSEMBLY ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs. Center Rafter Support Center Spacer Solid Center Block 8 sided PARTS LIST 12’ GAZEBO ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs. 10' Assembly Center Rafter Support (2) 3" Screw Center Block 2 x 4 x 43-1/16” 2 x 4 x 2-1/4” PARTS LIST 14’ GAZEBO ❑ 2 pcs. ❑ 3 pcs. ❑ 2 pcs.
PAGE 4
3 PARTS LIST 10’ GAZEBO ❑ 12 pcs. Rafters 2 x 4 x 27” ❑ 1 pc. Assembled Ridge from 2-A PARTS LIST 12’ GAZEBO ❑ 14 pcs. Rafters 2 x 4 x 33-1/8” ❑ 1 pc. Assembled Ridge from 2-A SECOND TIER ERECTING RAFTERS PARTS LIST 14’ GAZEBO ❑ 16 pcs. Rafters 2 x 4 x 38-5/8” ❑ 1 pc. Assembled Ridge from 2-A If you are assembling a 12’ or 14’ Second Tier, please begin with step 3-B, if you are assembling a 10’ Second Tier, please go to step 3-A.
PAGE 5
3 SECOND TIER RAFTER ASSEMBLY CONTINUED 3-C 10 1 11 2 3-C: Attach rafters 1, 2, 3, 4 to Ridge assembly first. Set on Gussets and attach with 1-5/8” screws, see 3-D for details. In windy conditions, have a second person hold this assembly in place until rafters 5 and 6 are installed. Layout and attach remaining rafters according to 3-C for easier assembly. Install rafters in same order for 12’ and 14’ model gazebos. 7 6 5 9 3 12 4 8 NOTE: Adjust Wall corners in (or out) to fit.
PAGE 6
3 PARTS LIST 10’ GAZEBO ❑ 2 pcs. Roof Finial Block SECOND TIER RAFTER ASSEMBLY CONTINUED PARTS LIST 12’ GAZEBO ❑ 2 pcs. Ridge Cap Tops ❑ 2 pcs. Roof Finial Block PARTS LIST 14’ GAZEBO ❑ 2 pcs. Ridge Cap Tops ❑ 2 pcs. Roof Finial Block 3-E: For 12’ and 14’ Gazebo Only For 12’ and 14’ Gazebos, attach Ridge Cap to top of Ridge Block with four 1-5/8” screws as in Fig.1. (4) 1-5/8" Screws into each Ridge Cap Fig.1 12' & 14' GAZEBO TOP VIEW 3-F: Add Roof Finial Block to top as shown with 3” screws .
PAGE 7
4 ASSEMBLING SECOND TIER ROOF CONTINUED PARTS LIST 10’ GAZEBO PARTS LIST 12’ GAZEBO PARTS LIST 14’ GAZEBO ❑ ❑ ❑ ❑ ❑ ❑ 10 pcs. ❑ 2 pcs. ❑ 10 pcs. ❑ 2 pcs. ❑ 12 pcs. ❑ ❑ ❑ ❑ ❑ 8 pcs. 2 pcs. 8 pcs. 2 pcs. 10 pcs. Triangular Roof Panels Square Roof Panels Fascia Fascia long Fascia Trim 5 6 7 4 4-A Fig.1 Square Roof Panels Should Overhang Rafter End Triangular Roof Panels Square Roof Panels Fascia Fascia long Fascia Trim 12 pcs. 2 pcs. 12 pcs. 2 pcs. 14 pcs.
PAGE 8
5 INSTALLING DRIP EDGE, SHINGLES, METAL CAP AND SPINDLE ❑ 1 Bundle ❑ 2 Bundle ❑ 20 feet ❑ 1 Pc. ❑ 1 Pc. Shingles (not included) for 10’ & 12’ Gazebo Shingles (not included) for 14’ Gazebo Drip Edge (not included) for 10’, 12’ & 14’ Metal Roof Cap from Gazebo Roof Finial from Gazebo Caulking the Roof Seams before shingling will improve the water resistance of your Gazebo.