6904 ! STOP DO NOT RETURN TO THE STORE! If you discover missing or damaged parts, or if you have questions about the building process, please reach out to us directly for the fastest service. 24/7 Support help.backyardproducts.com Answers to frequently asked questions Business Hours (734) 242-6900 Monday - Friday ........... 8:00am - 6:00pm EST Saturday - Sunday .................................
(This page intentionally left blank.
ASSEMBLY MANUAL 16904 12-20-2022 GABLE 8' x 10' (244 x 302,8 cm) ACTUAL FLOOR SIZE IS 96 x 120" (243,2 x 302,8 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE I M PO RTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY. BEFORE YOU BEGIN • BUILDING RESTRICTIONS AND APPROVALS Be sure to check local building department and homeowners association for specific restrictions and/ or requirements before building.
TOOLS Required ❑ Phillips Optional ❑ Tool Belt/ ❑ Utility Knife Screwdriver Nail Pouch ❑ Shingle Blades ❑ Drill / Driver ❑ 1/8" Drill Bit ❑ 1/4" Drill Bit ❑ 5/16" Drill Bit ❑ 1/2" Drill Bit ❑ #2 Philips Drive Bit ❑ Tin Snips ❑ Caulk Gun (for drip edge) ❑ Chalk Line ❑ Paint Tools ❑ Hammer ❑ Nail Gun ❑ Pencil ❑ Ladder ❑ Tape Measure ❑ Square • gun nails ❑ Safety Glasses ❑ Level ❑ Gloves or Safety! Always use approved safety glasses during assembly.
ADDITIONAL MATERIALS FOUNDATION OR FLOOR MATERIALS • This shed includes a complete floor. • See the FLOOR LEVELING section on page 7 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. REINFORCED WOOD FLOOR FRAME (OPTIONAL) IMPORTANT! This floor has been designed for general use. Depending on your specific use you may want to construct a heavy duty floor frame by adding additional floor joists (shown below as shaded).
Part identification letters are stamped on some parts. RS PARTS IDENTIFICATION AND SIZES WOOD SIZE CONVERSION CHART Nominal Board Size Treated lumber is stamped: Actual Size 2 x 4..............1-1/2" x 3-1/2" (3,8 x 8,9 cm) 1 x 4................ 3/4" x 3-1/2" (1,9 x 8,9 cm) 2 x 3..............1-1/2" x 2-1/2" (3,8 x 6,3 cm) 1 x 3................ 3/4" x 2-1/2" (3,8 x 6,3 cm) RS Check these locations for part stamp. PARTS LIST FLOOR INVENTORY YOUR PARTS before you begin.
PARTS LIST continued... WALL PANELS & DOORS Wall panels are 3/8" (1,0 cm) thick. x2 3/8 x 15-7/8 x 72" (1 x 40,3 x 182,9 cm) x2 3/8 x 23-7/8 x 72" (1 x 68,3 x 182,9 cm) NOTE: Panel parts are not stamped. x6 3/8 x 48 x 72" (1 x 121,9 x 182,9 cm) x1 x1 x1 x1 x1 LEFT DOOR x1 RIGHT DOOR 35-3/4" x 72" (90,8 x 182,9 cm) ROOF PANELS Roof panels are 7/16" (1,1 cm) thick. NOTE: Panel parts are not stamped.
PARTS LIST continued... FASTENER/HARDWARE BAG x155 NOTE: 1-1/2" (3,8 cm) x120 If you are using a nail gun, nails may be used where screws are shown for quicker assembly. Length of nail must match screw length. 2" (5,1 cm) x80 3" (7,6 cm) x65 2" (5,0 cm) x48 1-1/4" (3,2 cm) x195 1-1/2" (3,8 cm) NAIL BOXES (Shown Actual Size) x3 BOXES 3" (7,6 cm) x5 BOXES 2" (5,1 cm) HARDWARE / VENTS H 2.
COMPONENT SECTION INDEX I H N E G J J J F G B K M B L A B C D B O Description Section Floor Walls Wall Tie Plates Strap Ties Rafters Hurricane Ties Gable Units Roof Clips Roof Panels Trim Doors Door Hardware Corner Trim Collar Ties Earth Augers Shingles A B C D E F G H I J K L M N O - 7 Page 8 15 16 22 30 32 33 35 38 41-43 44 50 52 53 55 56
FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS • 3" Screws angled into 4x4. • (2) at each point frame • and 4x4 touch. 12" (30,5 cm) Measurements to centers of 4x4's. MATERIAL REQUIRED 12" (30,5 cm) x2 4 x 4 x 10' (10 x 10 x 304,8 cm) Treated Lumber Fasteners for Frame to 4 x 4. (3" Screws shown as one option.
CONCRETE FOUNDATION If you choose to install your kit on a concrete slab refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. C 3-1/2" (8,9 cm) B A OR DO 4" (10,2 cm) Building Size Actual Floor Size 8'x 10' (243,8 x 304,8 cm) 10' (295,9 x 235 cm) A B 96" (243,8 cm) 113" (287 cm) C 120" (305 cm) Requires: x2 2 x 4 x 10' (5,1 x 10,2 x 304,8 cm) x2 2 x 4 x 8' (5,1 x 10,2 x 243,8 cm) MUST be treated lumber. MUST be treated lumber.
FLOOR FRAME PARTS REQUIRED: x9 x2 x40 Look for 3" (7,6 cm) TREATED 2 x 4 x 93" (5,1 x 10,2 x 236,2 cm) Stamp x2 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm) BEGIN 1 Arrange parts as shown on flat surface. Measure and mark. Secure with (2) 3" nails at each mark and (4) 3" nails at seams. 120" (304,8 cm) 112" (284,5 cm) HINT: For easier nailing stand on frame.
LEVEL AND SQUARE FLOOR FRAME Before installing floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. BEGIN 1 See page 7 for the preferred floor leveling method. 2 Use level and check the frame is level before applying floor panels. 3 Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square.
FLOOR PANELS PARTS REQUIRED: Floor panels are 5/8" (1,6 cm) thick. 48" x 96" (121,9 x 243,8 cm) x1 x4 2" (5,1 cm) 3/4" GAUGE BLOCK Install all floor panels with the painted grid lines facing up. BEGIN 1 Install (1) 48" x 96" panel on the wall frame, as shown. Use the gauge block to mark the 3/4" side measurement floor joist. Secure panel with (2) 2" nails in the corners (Fig. A). 2 Move to the opposite end.
FLOOR PANELS PARTS REQUIRED: x1 48" x 96" (121,9 x 243,8 cm) x1 x167 23-7/8" x 96" (60,6 x 243,8 cm) 3/4" GAUGE BLOCK 3 Install (1) 48" x 96" panel flush to installed panel. Secure with 2" nails spaced 6" apart on edges and 12" apart inside panels. 4 Install (1) 23-7/8" x 96" panel flush to installed panel. Secure with 2" nails spaced 6" apart on edges and 12" apart inside panels.
IMPORTANT! Ensure the floor frame is level after installing floor panels. Re-level if needed. We recommend installing Earth Augers to anchor the floor before installing any walls. Auger installation will be much easier by installing at this time. See page 55 for Earth Auger installation instructions. x6 HINT: 30" Earth Auger • The floor should be used as a stable work surface for wall construction. • Organize your assembly procedure during the build process to avoid over-handling of the walls.
SIDE WALL FRAME PARTS REQUIRED: x2 RL x6 UM x2 TP x28 2 x 4 x 24" (5,1 x 10,2 x 61 cm) 3" (7,6 cm) 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,2 cm) Build two identical side walls. BEGIN 1 HINT: For easier nailing stand on frame. Arrange parts on edge on floor. Measure and mark. Secure with (2) 3" nails at each mark and (4) 3" nails at seams.
SIDE WALL FRAME PARTS REQUIRED: x4 2 x80 H 2.5 Tie Plate Install (4) H 2.5 tie plates at the bottom of four wall studs. Secure with 1-1/2" nails (Fig. A). Nail all nail holes. Fig. A H 2.5 1-1/2" (3,8 cm) Nails Turn wall over to the opposite side before installing wall panels. (H 2.5 tie plates will be on inside of building.
SIDE WALL PANELS PARTS REQUIRED: x1 x45 48" x 72" (121,9 x 213,4 cm) 2" (5,1 cm) 3/4" GAUGE BLOCK Install all panels with the primed side facing up. 3 Install (1) 48" x 72" panel on the wall frame, as shown. Use the gauge block to mark the 3/4" side measurement on the wall stud. Secure panel with (2) 2" nails in the corners (Fig. A). 4 Move to the opposite end. Using the long edge of the panel as a lever, move the panel side-to-side until you have a 3/4" measurement on the wall stud.
SIDE WALL PANELS PARTS REQUIRED: x1 5 x77 x1 48 x 72" (121,9 x 213,4 cm) 3/4" GAUGE BLOCK 23-7/8 x 72" (68,3 x 182,9 cm) Install (1) 48" x 72" panel first. Second, install the 23-7/8" x 72" panel. Secure with 2" nails spaced 6" apart on edges and 12" apart inside panel. Flush 6" (15,2 cm) 12" (30,5 cm) 3/4" GAUGE BLOCK 23-7/8" (68,3 cm) 48" (121,9 cm) Repeat steps to build your second side wall. FINISH Your side walls are now assembled. Carefully flip the side wall over.
BACK WALL FRAME PARTS REQUIRED: x5 x2 x20 3" (7,6 cm) UM 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm) SZ 2 x 4 x 89" (5,1 x 10,2 x 226,1 cm) BEGIN 1 Arrange parts on edge on floor. Measure and mark. Secure with (2) 3" nails at each mark.
BACK WALL PANELS PARTS REQUIRED: x2 x90 2" (5,1 cm) 3/4" GAUGE BLOCK 48" x 72" (121,9 x 182,9 cm) Install all panels with the primed side facing up. 2 Install (2) 48" x 72" panels, as shown. Secure panels with 2" nails spaced 6" apart along edges and 12" apart on inside of panel. 3-1/2" (8,9 cm) Flush For squareness maintain flush and 3/4" measurement along panel edges. BEGIN HERE 3/4" (1,9 cm) Flush 6" (15,2 cm) 12" (30,5 cm) Flush 3/4" GAUGE BLOCK FINISH Your back wall is now assembled.
FRONT WALL FRAME PARTS REQUIRED: x2 x6 x1 x40 AJ 3" (7,6 cm) 2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm) UM 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm) SZ 2 x 4 x 89" (5 x 10,2 x 226,1 cm) BEGIN 1 Arrange parts on edge on floor. Measure and mark. Secure with (2) 3" nails at each conjunction and as shown. HINT: For easier nailing stand on frame. 89" (226,1 cm) 12-1/2" (31,8 cm) 64" (162,6 cm) 12-1/2" (31,8 cm) 12-1/2" (31,8 cm) measurements are to edge of studs.
FRONT WALL FRAME PARTS REQUIRED: x24 x4 2 LSTA9 Strap Tie Install (4) LSTA9 strap ties centered at the top and bottom of front inner door studs, as shown. Secure with 1-1/2" nails (Fig. A). All holes must be nailed. Flush Strap Ties to frame. 1-1/2" (3,8 cm) Nails LSTA9 Strap Tie 3 Turn wall to the opposite side and secure tie straps on opposite side of wall.
FRONT WALL PARTS REQUIRED: x1 x2 x2 OY 3" (7,6 cm) x60 2 x 3 x 72" (5,1 x 7,6 x 182,9 cm) TEMPORARY SUPPORT 2" (5,1 cm) 15-7/8 x 72" (40,3 x 182,9 cm) Install all panels with the primed side facing up. 4 Install (2) 15-7/8" x 72" panels onto wall frame, as shown. Secure panel with 2" nails spaced 6" apart. 5 Install OY as a brace to maintain 64" (162,6 cm) opening. Secure OY with (2) 3" screws.
RIGHT SIDE WALL INSTALLATION PARTS REQUIRED: x1 x10 OY 2 x 3 x 72" (5,1 x 7,6 x 182,9 cm) TEMPORARY SUPPORT x2 x23 3" (7,6 cm) 3" (7,6 cm) 2" (5,1 cm) BEGIN 1 Center right side wall on floor. 1" (2,5 cm) overlap is to the bottom. Install OY as a temporary brace. Secure with (2) 3" screws. 3" (7,6 cm) Screws R O O D OY 1" (2,5 cm) 2 Secure panel to floor frame with 2" nails spaced 6" apart. Angle nail into floor frame (Fig. A). 3 Secure wall bottom plates to floor with 3" nails (Fig. A).
BACK WALL INSTALLATION PARTS REQUIRED x18 x1 x2 3" (7,6 cm) 2" (5,1 cm) x11 1-1/2" (3,8 cm) x8 3" (7,6 cm) Fig. B BEGIN 1 2" (5,1 cm) Secure back wall with (1) 2" screw into side wall bottom plate (Fig. A) and top plate (Fig. B). 2" (5,1 cm) Screw Flush ENSURE PANEL CORNERS ARE FLUSH. 2" (5,1 cm) Screw Fig. A 2 Secure panels to floor with 2" nails spaced 6" apart. Angle nails into floor frame (Fig. C). 3" (7,6 cm) Screw Secure wall bottom plates to floor with 3" nails (Fig. C).
LEFT SIDE WALL INSTALLATION PARTS REQUIRED: x2 2" (5,1 cm) BEGIN 1 Install left wall, securing with (1) 2" screw through back wall panel into side wall bottom and top plates (Fig. B, Fig. A). 2" (5,1 cm) Screw Fig. B ENSURE PANEL CORNERS ARE FLUSH. Flush Fig.
LEFT SIDE WALL INSTALLATION PARTS REQUIRED: x23 x1 2" (5,1 cm) x11 2 x10 1-1/2" (3,8 cm) 3" (7,6 cm) 3" (7,6 cm) Nail side wall panels to floor frame with 2" nails spaced 6" apart. Angle nails into floor frame (Fig. C). 3" (7,6 cm) Nails Secure wall bottom plates to floor with 3" nails (Fig. C). 6" (15,2 cm) Nail 2" nails first. 3" (7,6 cm) Nails 2" (5,1 cm) Nails Fig. C 3" (7,6 cm) Screw Fig. D 3 Nail back wall panel to side wall stud with 1-1/2" nails spaced 6" apart.
FRONT WALL INSTALLATION PARTS REQUIRED x10 2" (5,1 cm) x22 1-1/2" (3,8 cm) x2 x4 2" (5,1 cm) 3" (7,6 cm) Fig. B BEGIN 1 x4 3" (7,6 cm) 2" (5,1 cm) Screw Secure front wall with 2" screws into top and bottom plates (Fig. A, Fig. B). Flush ENSURE PANEL CORNERS ARE FLUSH. Flush 2 Nail panels to floor with 2" nails spaced 6" apart. Angle nails into floor frame (Fig. C). Secure panels to both side wall studs with 1-1/2" nails. Secure wall bottom plates to floor with 3" nails (Fig. C).
FRONT WALL HEADER PARTS REQUIRED: x1 ¸1 x5 PBZ 3" (7,6 cm) 2 x 3 x 76" (5,1 x 7,6 x 193 cm) BEGIN Center PBZ on SZ flush to edge of panel (Fig. A). Secure with (5) 3" screws spaced evenly, as shown. Angle screws into header. Fig. A Flush to panel edge Front wall panel PBZ 3" (7,6 cm) Screws CENTER CENTER FINISH Your front wall header is installed.
RAFTERS PARTS REQUIRED: x10 x1 SBA OSB OR WOOD GRAIN 2" (5,1 cm) 2 x 4 x 21" (5,1 x 10,2 x 53,3 cm) 6 x 24" (15,2 x 61 cm) x12 x120 TEMPORARY SUPPORT WI 2 x 4 x 54-1/16" (5,1 x 10,2 x 137,3 cm) You will build Six assemblies. (4) with two gussets, and (2) with one gusset. ¸1 BEGIN Place two rafter halves flush in corners of 2nd studs from back wall and flush to side wall panels. Place temporary support SBA beneath rafters at peak.
RAFTER INSTALLATION PARTS REQUIRED: x4 Preassembled ¸1 x20 3" (7,6 cm) x2 (1) GUSSET Preassembled BEGIN Secure rafters to top plate with (2) 3" screws in each rafter end (Fig. A, Fig. B). - Note single-gusset rafters at front & back walls with gusset facing inward. Secure single-gusset rafters to top plate with (1) 3" screw in each rafter end (Fig. C). Fig.
RAFTER INSTALLATION PARTS REQUIRED: x8 2 x80 1-1/2" (3,8 cm) H 1 Hurricane Tie Working inside, install (8) H1 Hurricane Ties at the base of the four inner rafters. Ensure H1 ties are flush up to bottom of rafter. Secure with 1-1/2" nails (Fig. A). 1-1/2" (3,8 cm) Nails Flush H1 Hurricane Tie Repeat to install (4) H1 Hurricane Ties on opposite side. FINISH Your rafters and hurricane ties are now installed. 32 Fig.
BACK GABLE UNIT PARTS REQUIRED: x8 x1 SBA x1 2 x 4 x 21" (5,1 x 10,2 x 53,3 cm) x1 Install all panels with the primed side facing up. BEGIN 1 Place left gable panel on SBA as shown. Secure with 1-1/2" nails as shown. 1-3/4" (4,5 cm) 1-1/2" (3,8 cm) Nails SBA (on flat) 1-3/8" (3,5 cm) 2 Place right gable panel flush to left panel. Secure with 1-1/2" nails, as shown. 1-1/2" (3,8 cm) Nails Flush FINISH Your back gable unit is now assembled.
BACK GABLE UNIT INSTALLATION PARTS REQUIRED: x38 x2 1-1/2" (3,8 cm) 3" (7,6 cm) Back Gable Unit ENSURE GABLE IS CENTERED ON WALL BEFORE NAILING. BEGIN 1 Measure 1-3/8" down from top plate and mark at each side, as shown. Set gable unit on top plate. Secure with (1) 1-1/2" nail on each side. 2 Continue nailing lower edge of panels into top plate with 1-1/2" nails spaced 6" apart. Secure panels to rafter with 1-1/2" nails spaced 6" apart.
FRONT GABLE UNIT PARTS REQUIRED: x8 x2 x1 CLA 2 x 4 x 4-7/8" (5,1 x 10,2 x 12,4 cm) x1 Install all panels with the primed side facing up. BEGIN 1 Install left gable panel on parts CLA, as shown. Secure with 1-1/2" nails, as shown. 1-3/4" (4,4 cm) 1-1/2" (3,8 cm) Nails Flush CLA (on flat) 1-3/8" (3,5 cm) 1-3/4" (4,4 cm) 2 Install right gable panel flush to left panel. Secure with 1-1/2" nails, as shown. 1-1/2" (3,8 cm) Nails Flush Flush FINISH Your front gable unit is now assembled.
FRONT GABLE UNIT INSTALLATION PARTS REQUIRED: x40 x2 1-1/2" (3,8 cm) 3" (7,6 cm) Front Gable Unit ENSURE GABLE IS CENTERED ON WALL BEFORE NAILING. BEGIN 1 Measure 1-3/8" down from top plate and mark at each side as shown. Set gable unit on wall header. Secure with (1) 1-1/2" nail on each side. 2 Secuer lower edge of panels to top plate and header with 1-1/2" nails spaced 6" apart. Secure panels to rafter with 1-1/2" nails spaced 6" apart.
ROOF PANELS ROOF CLIP INSTALLATION INSTRUCTIONS During installation of roof panels, it is important to install Roof Clips between all panels. x16 Roof Clip PSCL7/16" Install all roof panels with the rough side facing up (painted grid lines side). Fig. A Install PSCL7/16" roof clips in locations shown. Install roof clips with narrow tabs up. Ensure roof clips are oriented as shown in Fig. A. Install roof clips on all seams.
ROOF PANELS PARTS REQUIRED: 7/16 x 9-3/4 x x 23-7/8" (1,1 x 24,8 x 60,6 cm) x2 x4 2" (5,1 cm) 7/16 x 9-3/4 x 96" (1,1 x 24,8 x 243,2 cm) x2 7/16 x 23-7/8 x 48" (1,1 x 60,6 x 121,9 cm) x2 3/4" GAUGE BLOCK 7/16 x 48 x 96" (1,1 x 121,9 x 243,2 cm) x2 Install all roof panels with the rough side facing up (painted grid lines side). Roof panels may cause serious injury until securely fastened. Flush at peak BEGIN 1 Fig.
ROOF PANELS PARTS REQUIRED: 3 x4 Install 9-3/4"x 23-7/8" roof panel flush to installed panel and flush at rafter peak (Fig. B). 2" (5,1 cm) Flush at peak 9-3/4" x 23-7/8" Fig. B Secure with (2) 2" nails into panel corners, as shown. Two Nails 4 Move to the opposite end of panel. Maintain panel flush at peak (Fig. B). OR DO Use GAA gauge block for 3/4" measurement along outside edge of gable panel (Fig. C). Secure panel with (2) 2" nails in the corners. Flush at peak Fig.
ROOF PANELS PARTS REQUIRED: x118 2" (5,1 cm) Roof Clip PSCL7/16" x16 Install PSCL7/16 roof clips between all panels. 5 Maintain spacing between the center of the rafters. To outside of gable panel 24-3/4" (62,9 cm) Secure with (1) 2" nail into each rafter (Fig. D). MEASUREMENTS BETWEEN RAFTERS 24" (61 cm) Fig.
GABLE FASCIA - FRONT PARTS REQUIRED: x1 x1 x32 BSR 2" (5,1 cm) 19/32 x 3-1/2 x 58-7/8" (2,5 x 8,9 x 149,5 cm) BSL 19/32 x 3-1/2 x 58-7/8" (2,5 x 8,9 x 149,5 cm) Install all trim boards with the primed side facing out. BEGIN Install BSL and BSR flush at rafter peak and flush to top of OSB roof panels. Fasten trim with 2" finishing nails in pattern shown.
EAVE SOFFIT PARTS REQUIRED: x2 EFC x2 OY x32 2 x 3 x 49-1/2" (5,1 x 7,6 x 125,7 cm) 1-1/4" (3,2 cm) 2 x 3 x 72" (5,1 x 7,6 x 182,9 cm) BEGIN 1 Place parts OY and EFC flush to bottom of roof overhang and wall panel as shown (Fig. A). Secure with 1-1/4" screws in the pattern shown. EFC OY 1-1/4" (3,2 cm) Screws Flush OY 1-1/4" (3,2 cm) Screw EFC Flush FINISH You have finished installing your eave soffits. 42 Fig.
EAVE FASCIA PARTS REQUIRED: x2 x2 ROR x24 2" (5,1 cm) 2 x 2-1/2 x 28-1/2" (5,1 x 6,3 x 72,4 cm) DKB 19/32 x 2-1/2 x 93" (2,5 x 6,3 x 236,2 cm) Install all trim boards with the primed side facing out. ¸1 BEGIN Install eave fascia boards ROR and DKB, as shown (Fig. A). Secure with 2" finishing nails. ROR DKB Flush at seam ROR DKB Fig. A Flush to roof panels and soffit 2" (5,1 cm) Finishing Nails FINISH You have installed your eave fascia.
DOORS PARTS REQUIRED: x1 2" (5,1 cm) 3/8 x 1-3/4 x 71-1/2" (1 x 4,4 x 181,6 cm) x2 35-3/4" x 72" (90,8 x 182,9 cm) x2 x24 Temporary Spacer DBA 2 x 4 x 72-3/8" (5,1 x 10,2 x 182,9 cm) PVC x2 Piano Hinge Install right and left door hinges and hinge boards to doors. BEGIN 1 Stand right door on edge, as shown. Measure and mark location from top of door. 2 Install hinge with knuckle facing up. Secure with (12) 2" screws.
DOORS PARTS REQUIRED: x24 4 Stand left door on edge, as shown. Measure and mark location from top of door. 5 Install hinge with knuckle facing up. Secure with (12) 2" screws. 2" (5,1 cm) Top is stamped TOP 2" (5,1 cm) Screws Hinge knuckle in upward position. POT Outside Face of Door 3/8" TOP DBA 3/4" Install hinge-board DBA as shown. Use a 3/8" board as a spacer. Secure with (12) 2" screws.
DOOR INSTALLATION PARTS REQUIRED: x1 x1 x4 Temporary Spacer 3" (7,6 cm) 3/8 x 1-3/4 x 71-1/2" (1 x 4,4 x 181,6 cm) DBA Temporary Support 7/16" BIT (11 mm) 2 x 4 x 72-3/8" (5,1 x 10,2 x 182,9 cm) PVC BEGIN 1 Hold DBA in place, centered over door opening and flush along the upper edge of top plate. Pre-drill four evenly spaced 7/16" screw holes through DBA into header. Mark center of door opening on top plate - this mark will be used later.
DOOR INSTALLATION PARTS REQUIRED: x3 Door - Hinge Board Assembly 3" (7,6 cm) RIGHT 3 Mark the outside center of the door opening. Measure 3/16" either side of the center mark; the 3/16" mark will be the reference mark to align the door edges. 4 Set right door on support DBA and align upper corner to the 3/16" reference mark. Ensure hinge board DBA is flush against wall panel. Secure (1) 3" deck screw into the wall framing (top plate). Install the TOP screw first.
DOOR INSTALLATION PARTS REQUIRED: x3 Door - Hinge Board Assembly 3" (7,6 cm) LEFT 6 Set left door on support DBA and align upper corner to the 3/16" reference mark. Ensure hinge board DBA is flush against wall panel. Secure (1) 3" deck screw into the wall framing (top plate). Install the TOP screw first.
DOOR INSTALLATION PARTS REQUIRED: x1 x1 x22 3" (7,6 cm) DBA 2 x 4 x 72-3/8" (5,1 x 10,2 x 182,9 cm) PVC x8 1-1/4" (3,2 cm) 1/2 x 2-7/8 x 68-3/4" (1,3 x 7,3 x 174,6 cm) PVC 10 Remove temporary support DBA and install it centered over door opening, flush on top of hinge boards. Use the four pre-drilled screw holes. Secure with (4) 3" screws. 7/16" (11 mm) Pre-drilled holes 3" (7,6 cm) Screws DBA 11 Reinforce hinge boards with (18) 3" screws into door studs, in the pattern shown.
DOOR HARDWARE PARTS REQUIRED: x8 1-1/4 (3,2 cm) x2 ¸1 3/8" BIT (9,5 mm) BEGIN 2 Install top spring bolt to the upper end of PVC weatherstrip (Fig. A). Secure with (4) 1-1/4" screws. Mark spring bolt pin location on over door frame. Drill a 1-1/2" deep hole using a 3/8" drill bit. Install bottom spring bolt to the lower end of PVC weatherstrip (Fig. B). Secure with (4) 1-1/4" screws. Mark spring bolt pin location on floor. Drill a 1-1/2" deep hole using a 3/8" drill bit. Fig.
DOOR HARDWARE PARTS REQUIRED: x2 x1 3/32" (3 mm) Drill Bit 1" (2,5 cm) 1/2" (13 mm) Drill Bit x2 1-1/4" (3,2 cm) BEGIN 1 Measure and mark location of hole on outside of right door as shown (Fig. A). Pre-drill hole with 1/4" drill. 2 Re-drill hole with 1/2" drill (Fig. B). Keep drilled hole square. RIGHT DOOR 1-1/2" (3,8 cm) Fig. B 1/2" 1,3 cm 35-3/4" 90 cm SIDE VIEW 3 Secure back plate with 1" screws and handle with 1-1/4" screws as shown.
CORNER TRIM PARTS REQUIRED: x8 x48 2" (5,1 cm) 3/8 x 1-3/4 x 71-1/2" (1 x 4,4 x 181,6 cm) BEGIN 1 Front and back 71-1/2" corner trim is flush under gable panel (Fig. A) and flush along the face of side wall panel. Secure with 2" finishing nails, spaced evenly. 2 Install 71-1/2" side corner trim is flush under soffit board and flush along edge of front and back corner trim. Secure with 2" finishing nails, spaced evenly. Repeat steps to install trim to all four corners. 71-1/2" on gable walls Fig.
GABLE VENT, COLLAR TIES and DOOR THRESHOLD PARTS REQUIRED: x4 x24 GUA 1 x 4 x 60" (2,5 x 10,2 x 152,4 cm) x1 63-7/8" Metal Threshold 3/4" (1,9 cm) x11 2" (5,1 cm) x1 x4 1" (2,5 cm) Bagged separately / special coating ¸1 BEGIN Caulk behind vent flanges. Install vent in front gable. Secure with 1" screws. Fig. A 2 Install collar tie to the rafter with (3) 2" nails at each end (Fig. A). Starting at the wall with the door, install (4) collar ties GUA on the four center rafters, as shown.
WALL VENTS PARTS REQUIRED: x12 1/2" (1,3 cm) 8 x 16" (20,3 x 35,6 cm) x2 ¸1 You can place your side wall vent on either side of shed BEGIN Locate and mark for vents in side walls. Install (1) vent near the floor and (1) vent near the eave. Caulk behind vent flanges. Secure with 1/2" screws.
AUGER STAKES PARTS REQUIRED: x6 x6 5/8" x 2-1/2" (16 mm x 6,3 cm) 30" Earth Auger Ratchet Handle & Socket Lag Screw Flat Washer x6 Large Screwdriver 1/2" x 2" x 2" (13 mm x 50,8 mm) BEGIN 1 After the floor is in the final location, install (6) augers as shown, at measured locations. Secure the augers to bond boards with 2-1/2" lag screws and 2" flat washers (Fig. A). Min. 1-1/4" (3,2 cm) for siding clearance. Fig.
PAINT & CAULK - NOT INCLUDED - • Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. • Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: • Bottom edge of all siding and trim • Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting. (Follow directions provided by manufacturer.
SHINGLES - NOT INCLUDED • Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch SHINGLE NAIL PATTERN 1" (2,5 cm) 1/2" (1,3 cm) Notch Sealing Strip 1" (2,5 cm) Half A Rain Slot Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. BEGIN 1 Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.
SHINGLES continued... 2 2 Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge. Roof Deck FRONT OF SHED 1" (2,5 cm) Notch BACK OF SHED Flush with starter row. - or - Drip Edge Flush with starter row. Notch 3 Install second row of shingles flush at top of first row's rain slots. Ensure 1" overhang or flush to drip edge at front, stagger each row. FRONT OF SHED BACK OF SHED 1" (2,5 cm) Notch Flush with rain slots.
SHINGLES continued... 5 Continue installing rows of shingles to the peak. At the peak make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at ridge cut to peak with a utility knife. Cut Off. 5" (12,7 cm) MAX. CUT Top of rain slot. 5" (12,7 cm) or less. • If more than 5" to rain slot you must install another row of shingles. 6 Repeat steps 1 - 5 to shingle the opposite side of your roof. Trim shingles at ridge.
SHINGLES - RIDGE CAP • You will finish off the top of the roof with a ridge cap made from shingles. BEGIN 1 Cut shingles into THREE pieces. Hint: Use cut-off pieces first. 2" (5 cm) 2" (5 cm) 2" (5 cm) 2" (5 cm 2" (5 cm) 2" (5 cm) Score shingle, then snap-off angled cut. Weather Seal Top of slot. Note: • You will need about 27 - 29 cut pieces. 2 27 to 29 Pieces Install first ridge cap flush to shingles at front, as shown. (1) Nail per side through weather seal.
SHINGLES - RIDGE CAP continued... 4 Continue installing ridge cap to back of roof. 5 Make sure there is 4" between the shingle-color and edge of shingles. 4" (10 cm) 6 Trim cap off flush to shingles When you have 4" minimum of shingle color cut one piece to cap your roof. Cut at top of rain slot. Cap 7 Install flush to shingles. Flush to shingles (2) Nails per side. FINISH You have finished your ridge cap.
16904 8' x 10' Order Form CATEGORY PART DESCRIPTION 2X3 Nailer Soffit "A" Soffit "B" 2X4 Gable Connector - Front Gable Connector - Back Rafter Front/Back Wall Plate Sidewall Plate "A" Sidewall Plate "B" Frontwall Bottom Plate Wall Stud 2 X 4 TREATED FLOOR FRAME 1 X 3 PINE Floor Joist Bond Board "A" Bond Board "B" Gauge Block Collar Tie PART SIZE PART ITEM # BUILDING QTY.
LIMITED CONDITIONAL WARRANTY* Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for 1 year. 2. All accessories, hardware and metal components are warranted for 2 years. 3. All Oriented Strand Board (OSB) is warranted for 2 years 4. Siding and Trim is warranted for 10 years. 5. Solar Shed windows are warranted for 1 year. 6. Cedar lumber is warranted for 15 years. 7. Preserved Pine is warranted for 10 years. 8.
