User Manual

5Hangar 9 Taylorcraft 26cc BNF
Safe Operating Recommendations
• Inspectyourmodelbeforeeveryflighttomakecertainit
is airworthy.
• Beawareofanyotherradiofrequencyuserwhomay
present an interference problem.
• Alwaysbecourteousandrespectfulofotherusersof
your selected flight area.
• Chooseanareaclearofobstaclesandlargeenoughto
safely accommodate your flying activity.
• Makecertainthisareaisclearoffriendsandspectators
prior to launching your aircraft.
• Beawareofotheractivitiesinthevicinityofyourflight
path that could cause potential conflict.
• Carefullyplanyourflightpathpriortolaunch.
• AbidebyanyandallestablishedAMANationalModel
Aircraft Safety Code.
Important Information
Regarding Warranty
Please read our Warranty and Liability Limitations in the
back of this manual before building this product. If you as
the purchaser or user are not prepared to accept the liability
associated with the use of this Product, you are advised to
return this Product immediately in new and unused condition
to the place of purchase.
Using the Manual
This manual is divided into sections to help make assembly
easier to understand, and to provide breaks between each
major section. In addition, check boxes have been placed
next to each step to keep track of each step completed.
Steps with a single box () are performed once, while steps
with two or more boxes () indicate the step will require
repeating, such as for a right or left wing panel, two servos,
etc. Remember to take your time and follow the directions.
UltraCote® Covering Colors
White HANU870
True Red HANU866
Black HANU874
Transmitter Requirements
This model requires a minimum of a 6-channel radio to
operate all the functions of your aircraft. We suggest the
following radio systems available through Horizon Hobby or
your local hobby distributor.
Spektrum DX6i SPMR6610
Spektrum DX8 SPMR8800
Spektrum 10T
JR
®
DSM2 or DSMX Systems
Field Equipment Required
Fuel (gasoline)
2-cycle oil EVOX1001Q
Ultra fuel pump-manual HAN155
Double Vision
™
fast field charger HAN114
Optional Field Equipment
PowerPro
™
12V Starter HAN161
12V 7Ah Sealed Battery HAN102
Self-stick weights, 6 oz HAN3626
Spray cleaner
Paper towels
Included Components
Spektrum A6000 Servos (6) SPMSA6000
Spektrum AR8000 DSMX Receiver SPMAR8000
Spektrum 2700mAh 6.0V Ni-MH Rx Pack SPMB2700NM
Zenoah G26 Air Magneto Engine ZENE26A
Zenoah Ignition Kill Switch ZEN20000
Hangar 9 Aluminum CNC 2
1
/
2
-inch Spinner HAN4902015
Hangar 9 Fuel Filler with Overflow Fitting HAN116
Evolution
®
16 x 6 Propeller EVO16060
Required Tools
Low-tack tape Needle nose pliers
Nut driver: 1/4-inch Phillips screwdriver: #1, #2
Side cutter
Open end wrench: 1/4-inch, 12mm, 17mm
Hex wrench: 5/64-inch, 3/32-inch, 1/8-inch, 2.5mm,
7/64-inch, 4mm
Required Adhesives
Silicone adhesive DEVS250
Thin CA PAAPT08
Threadlock PAAPT42
Before Starting Assembly
Before beginning the assembly of your model, remove
each part from its bag for inspection. Closely inspect the
fuselage, wing panels, rudder and stabilizer for damage. If
you find any damaged or missing parts, contact the place
of purchase.
If you find any wrinkles in the covering, use a heat gun
(HAN100) and covering glove (HAN150) or covering iron
(HAN101) with a sealing iron sock (HAN141) to remove
them. Use caution while working around areas where the
colors overlap to prevent separating the colors.
Note: The hardware to complete each section of
the manual is located in the bag with the items
required. Leave items in their bags until instructed
to open them for use in building your model.