User's Manual

ManualsBrandsHangzhou HikAuto Technology ManualsCamera & PhotoDashCam

D Parts Introduction

E Dashcam Installation

E Car Fragrance Installation

F Mobile Phone Connection G Function Description

H Cautions

I Troublshooting

I Troubleshooting

Model

Aperture

Pixel

Max. Resolution

Angle

Storage

G-Sensor

Wi-Fi

Sound Recording

Power Supply

Power Consumption

Operating Temperature and Humidity

Installation Type

Dimensions (L × W × H)

Weight

AE-DC4015-F5

F1.8

1440P

2560 × 1440@ 30fps

103°(horizontal) 56°(vertical) 123°(diagonal)

TF card, 16 GB to 256 GB

Built-in, collision triggered recording and recording lock

Yes

5 VDC, 1 A

＜ 2 W

-20 °C to 70 °C (-4 F to 158 F). RH 95%.

General

72.4 mm × 61.4 mm × 81.1 mm

Approx. 75 g

Scan QR Code

Specifications

Clean the windshield and

paste the electrostatic film

onto it.

Avoid introducing air bubble.

DO NOT paste the film

repeatedly.

Press the PUSH button, the

back cover of dashcam snaps

out, and gently buckle the

back cover until it is

completely removed.

Adjust the angle of the car

fragrance and load it into

the dashcam.

Finally, install the back cover

into the dashcam. For better

experience, it is recommended

to change the car fragrance

regularly for 4-6 weeks.

Peel off the release paper of

3M tape and install the

dashcam onto the center of

the electrostatic film. Connect

the dashcam with one end of

the power cord along the red

line shown in figure.

Connect car charger to

cigarette lighter and connect

the power cord to the USB

interface of car charger.

Adjust the surveillance angle

and the installation is

completed. The maximum

adjusting angle is 43°.

Scan the QR code to download and

install HikDashcam app.

Add the dashcam to the app.

a. Run the HikDashcam app.

b. Tap Wi-Fi Connection.

c. In Wi-Fi list, select the Wi-Fi SSID

of the target dashcam and enter

Wi-Fi password to build

connection.

• You can set the parameters of the

dashcam.

• For iOS, you need to go to Wi-Fi

settings of your phone to connect

to the Wi-Fi of dashcam.

Edit the dashcam password to

activate it to avoid abnormal

recording after connecting to Wi-Fi.

Dashcam Wi-Fi default parameters:

• Wi-Fi SSID: HIKVISION-F5-XXXX

(XXXX refers to the last four

characters of verification code.)

• Wi-Fi password: 1234567890

(please edit password after logging in

for the first time.)

Power On and Power Off

Power On: When you start up the engine, the dashcam powers on.

Power Off: When you turn off the engine, the dashcam powers off.

Recording

Two recording types are provided: Normal Reording and Emergency

Recording. Sound and mute recordings are selectable. Sound recording is set

as default. You can set audio settings on the device or turn off sound

recoding in app.

Safety Instruction

These instructions are intended to ensure that users can use the product

correctly to avoid danger or property loss.

Cautions: Injury or equipment damage may occur if any of the cautions are

neglected.

• In the use of the dashcam, you must be in strict compliance with the local

laws and regulations.

• You are recommended to install the dashcam on the location of rear

mirror to ensure the dashcam can record with the best surveillance view.

DO NOT install the dashcam on the location that will block the driver’s sight.

• Keep the user manual properly for future reference. See initial

connection of dashcam in user manual.

• Purchase the TF card from legal channel. To ensure safe and

stable data transmission, it is recommended to use TF card of

Class 10 or above.

• Format the new TF card first before using the card.

• To protect TF card from damage, shut down the dashcam before

installing and uninstalling TF card.

• If the dashcam is directly connected with the vehicle power

system, you are recommended to power off the dashcam when

the engine is off. Disconnect cigarette lighter to avoid insufficient

voltage and abnormal startup. Reconnect cigarette lighter to

ensure dashcam work normally when you start the car again.

• Operating temperature is from -20 C to 70 C (-4 F to 158 F). To

protect the dashcam, DO NOT use it in high temperature, low

temperature, or high-humidity environment. Keep the dashcam

from rain and dust.

• The manual is subject to update. The functions of dashcam may

vary according to different models.

*The driving assistance function of the device only sends alarm or warning to

the driver and cannot replace the driver’s judgement and operation. With the

device, you also should drive carefully to avoid traffic accident or violation.

Pedestrian or object recognition failure or recognition error may occur due to

external factors. DO NOT overly rely on the driving assistance function.

Trouble Solution SolutionTrouble

The dashcam drops

easily.

Starting the dashcam

failed.

The dashcam powers

off easily.

Recording is

abnormal.

Recording is blurred.

Recording is mute.

Dashcam reboots

itself.

Clean the windshield before installation.

Check whether the vehicle is started and power

supply is normal.

Check whether the car charger is tightly connected.

Restore to defaults: hold the RESET button until the

startup music is heard.

Make sure the power cord is in good condition.

Make sure the power cord is tightly connected to the

according interfaces.

Make sure that the dashcam started up successfully.

Check whether the TF card is inserted.

Check the status of TF card, e.g. its format, its lifespan.

Change TF card if it is not well.

Make sure the protective film is peeled off.

Check whether the windshield or the lens of dashcam

is blurred.

Set audio settings on the device or turn on sound

recording in HikDashcam app.

Check whether the car charger is equipped with power

supply interface of 5 VDC, ≥ 2 A.

The mobile phone

cannot display

recordings.

It may be relevant with the player or system of the

phone. Please connect TF card to your computer and

display the recordings.

External devices not

detected when you

connect dashcam to

computer with the

supplied power cord.

Dashcam does not support data transmission and the

supplied power cord is only for charging.

If you need to transfer data, please connect TF card

to your computer.

Wi-Fi connection

takes a long time.

It may be caused by the interferrence of the

surrounding Wi-Fi signals. Please use the dashcam in

an environment of less interferrence.

Shut down unnecessary programs in your phone to

release some resources for HikDashcam app and

reconnect Wi-Fi.

Dashcam Wi-Fi

password is forgotten.

The default password is 1234567890. If you have

revisied the password, regain the password by the

following steps.

1. Hold the RESET button on dashcam until the startup

music is heard and the dashcam is restored to

defaults.

2. Go to Wi-Fi Connection interface in HikDashcam

app. Select Wi-Fi SSID and log in with default

password 1234567890.

• The power mode of cigarette lighter may vary by different vehicle

types. Some may be powered constantly. In this case, please

make sure that the dashcam stops after you turn off the vehicle

engine. Otherwise, insufficient voltage may occur to vehicle battery.

• Make sure you have connected the dashcam to power according to

Step 2 and Step 3 in Installation section.

Check whether the car charger is tightly connected.

Check whether the 3M tape is tightly sticked to the

electrostatic film before the installation.

Turn on sound through the the audio control function

of the dashcam.

Mobile phone cannot

connect to dashcam.

Make sure HikDashcam app is installed.

Please restart the dashcam to the app.

1. Bracket

2. Lens

3. 3M Tape

4. Power Interface

5. TF Card Slot

6. Microphone

7. Speaker

8. RESET Button

(Restore the device to defaults.)

9. Pup-up Button of Car Fragrance