Camera Network Mini Dome Camera Quick Start Guide UD.
Network Bullet CameragQuick Start Guide Quick Start Guide COPYRIGHT ©2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Bullet CameragQuick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Bullet CameragQuick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Network Bullet CameragQuick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Bullet CameragQuick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Network Bullet CameragQuick Start Guide rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Bullet CameragQuick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
Network Bullet CameragQuick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Bullet CameragQuick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 2 Installation .................................................................................... 14 2.1 Ceiling Mounting ........................................................... 15 2.2 Ceiling Mounting with a Gang Box ................................ 18 2.3 Pendent Mounting ........................................................ 20 2.4 Wall Mounting .
Network Bullet CameragQuick Start Guide 1 Appearance Description 1 6 2 3 4 7 8 Figure 1-1 Overview (1) Figure 1-2 Overview (2) 11
Network Bullet CameragQuick Start Guide Table 1-1 Physical Description v No. Description 1 Front Cover 2 Dome Drive 3 Micro SD Card Slot 4 Network Cable 5 Lens 6 IR LED 7 Power Cable 8 Audio/Alarm Cables 9 Wi-Fi Antenna 10 Serial Port Interface 11 Hex Screw 12 MIC 13 RESET/WPS Button Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Bullet CameragQuick Start Guide v No.8 is the audio/alarm cable interface, of which the “I” mark connects to the alarm input, the “o” mark connects to the alarm output, the “GND” mark connects the grounding, and the “A” mark connects the audio output. v WPS (Wi-Fi Protected Setup, also known as AOSS or QSS) is a computing standard that attempts to allow easy establishment of a secure wireless network. Refer to user manual for details.
Network Bullet CameragQuick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet CameragQuick Start Guide 2.1 Ceiling Mounting Steps: 1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. Drill Template A 1 1 Hole A :for cables routed through the wall Screw hole1 :for Mounting Base FRONT Code:194101278 Figure 2-1 Drill Template 2. Loosen the set screw on the front cover to disassemble the camera with the supplied Allen key.
Network Bullet CameragQuick Start Guide 3. Hammer the plugs of the expansion screws to the ceiling. 4. Connect the power cable, network cable, and the audio/alarm cables. 5. Fix the camera body to the ceiling with the supplied expansion screws. Figure 2-3 Fix the Adapter Plate 6. View the image via the web browser. 7. Slightly loosen the hex screw beside the WPS/RESET button to adjust the surveillance angle. 8.
Network Bullet CameragQuick Start Guide Pan Adjusting Tool Rotation Tilt Figure 2-4 3-Axis Adjustment 9. Tighten the hex screw to fix the well-adjusted surveillance angle. 10. Align the front cover to the dome drive and tighten the set screws on the front cover. Figure 2-5 Install the Front Cover 11. Tear off the protection film softly to complete the installation.
Network Bullet CameragQuick Start Guide l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.2 Ceiling Mounting with a Gang Box Steps: 1. Fix the adapter plate to the gang box with the supplied PM4X8 screws. Figure 2-6 Fix the Adapter Plate 2. Fix the dome drive to the adapter plate with the supplied PM4X8 screws.
Network Bullet CameragQuick Start Guide Figure 2-7 Fix the Dome Drive 3. Connect the power cable, network cable, and the alarm/audio cables. 4. Align the front cover to the dome drive and tighten the set screws on the front cover.
Network Bullet CameragQuick Start Guide 5. Tear off the protection film softly to complete the installation. l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.3 Pendent Mounting Steps: 1. Install the bracket to the ceiling with the supplied screws in the bracket package. You need to purchases a pendant bracket separately if pendent mounting is adopted. 2.
Network Bullet CameragQuick Start Guide 3. Install the dome drive to the adapter plate. Figure 2-10 Fix the Dome Drive 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
Network Bullet CameragQuick Start Guide 5. Tear off the protection film softly to complete the installation. l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.4 Wall Mounting Steps: 1. Install the wall bracket to the wall with the supplied screws in the wall bracket package. You need to purchases a wall bracket separately if wall mounting is adopted. Figure 2-12 Install Wall Bracket 2.
Network Bullet CameragQuick Start Guide Figure 2-13 Fix the Adapter Plate 3. Fix the dome drive to the wall bracket with the supplied screws. Figure 2-14 Install the Camera 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
Network Bullet CameragQuick Start Guide Figure 2-15 Install the Front Cover 5. Tear off the protection film softly to complete the installation. l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.5 Install the Micro SD Card This series of camera supports local storage, please refer to the following steps to install the micro SD card. Steps: 1. Remove the front cover by loosening the set screws on it.
Network Bullet CameragQuick Start Guide Figure 2-16 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera.
Network Bullet CameragQuick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Network Bullet CameragQuick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Bullet CameragQuick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet CameragQuick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2.
Network Bullet CameragQuick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet CameragQuick Start Guide Note: Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Bullet CameragQuick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet CameragQuick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Bullet CameragQuick Start Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1) 34
Network Bullet CameragQuick Start Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
0
