User's Manual

ManualsBrandsHangzhou Hikvision Digital Technology ManualsCamera & PhotoNetwork Camera

Network Bullet CameragQuick Start Guide

Quick Start Guide

Any and all information, including, among others, wordings, pictures,

graphs are the properties of Hangzhou Hikvision Digital Technology

Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).

This user manual (hereinafter referred to be “the Manual”) cannot

be reproduced, changed, translated, or distributed, partially or

wholly, by any means, without the prior written permission of

Hikvision. Unless otherwise stipulated, Hikvision does not make any

warranties, guarantees or representations, express or implied,

regarding to the Manual.

About this Manual

This Manual is applicable to 25xx Network Camera.

The Manual includes instructions for using and managing the

product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The

information contained in the Manual is subject to change, without

notice, due to firmware updates or other reasons. Please find the

latest version in the company website

(

http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions. Other trademarks and

logos mentioned below are the properties of their respective

owners.

Summary of content (20 pages)

PAGE 1
Network Bullet CameragQuick Start Guide Quick Start Guide COPYRIGHT ©2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
PAGE 2
Network Bullet CameragQuick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
PAGE 3
Network Bullet CameragQuick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
Network Bullet CameragQuick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
Network Bullet CameragQuick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 6
Network Bullet CameragQuick Start Guide rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
PAGE 7
Network Bullet CameragQuick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
PAGE 8
Network Bullet CameragQuick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
PAGE 9
Network Bullet CameragQuick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 2 Installation .................................................................................... 14 2.1 Ceiling Mounting ........................................................... 15 2.2 Ceiling Mounting with a Gang Box ................................ 18 2.3 Pendent Mounting ........................................................ 20 2.4 Wall Mounting .
PAGE 10
Network Bullet CameragQuick Start Guide 1 Appearance Description 1 6 2 3 4 7 8 Figure 1-1 Overview (1) Figure 1-2 Overview (2) 11
PAGE 11
Network Bullet CameragQuick Start Guide Table 1-1 Physical Description v No. Description 1 Front Cover 2 Dome Drive 3 Micro SD Card Slot 4 Network Cable 5 Lens 6 IR LED 7 Power Cable 8 Audio/Alarm Cables 9 Wi-Fi Antenna 10 Serial Port Interface 11 Hex Screw 12 MIC 13 RESET/WPS Button Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
PAGE 12
Network Bullet CameragQuick Start Guide v No.8 is the audio/alarm cable interface, of which the “I” mark connects to the alarm input, the “o” mark connects to the alarm output, the “GND” mark connects the grounding, and the “A” mark connects the audio output. v WPS (Wi-Fi Protected Setup, also known as AOSS or QSS) is a computing standard that attempts to allow easy establishment of a secure wireless network. Refer to user manual for details.
PAGE 13
Network Bullet CameragQuick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
PAGE 14
Network Bullet CameragQuick Start Guide 2.1 Ceiling Mounting Steps: 1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. Drill Template A 1 1 Hole A :for cables routed through the wall Screw hole1 :for Mounting Base FRONT Code:194101278 Figure 2-1 Drill Template 2. Loosen the set screw on the front cover to disassemble the camera with the supplied Allen key.
PAGE 15
Network Bullet CameragQuick Start Guide 3. Hammer the plugs of the expansion screws to the ceiling. 4. Connect the power cable, network cable, and the audio/alarm cables. 5. Fix the camera body to the ceiling with the supplied expansion screws. Figure 2-3 Fix the Adapter Plate 6. View the image via the web browser. 7. Slightly loosen the hex screw beside the WPS/RESET button to adjust the surveillance angle. 8.
PAGE 16
Network Bullet CameragQuick Start Guide Pan Adjusting Tool Rotation Tilt Figure 2-4 3-Axis Adjustment 9. Tighten the hex screw to fix the well-adjusted surveillance angle. 10. Align the front cover to the dome drive and tighten the set screws on the front cover. Figure 2-5 Install the Front Cover 11. Tear off the protection film softly to complete the installation.
PAGE 17
Network Bullet CameragQuick Start Guide l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.2 Ceiling Mounting with a Gang Box Steps: 1. Fix the adapter plate to the gang box with the supplied PM4X8 screws. Figure 2-6 Fix the Adapter Plate 2. Fix the dome drive to the adapter plate with the supplied PM4X8 screws.
PAGE 18
Network Bullet CameragQuick Start Guide Figure 2-7 Fix the Dome Drive 3. Connect the power cable, network cable, and the alarm/audio cables. 4. Align the front cover to the dome drive and tighten the set screws on the front cover.
PAGE 19
Network Bullet CameragQuick Start Guide 5. Tear off the protection film softly to complete the installation. l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.3 Pendent Mounting Steps: 1. Install the bracket to the ceiling with the supplied screws in the bracket package. You need to purchases a pendant bracket separately if pendent mounting is adopted. 2.
PAGE 20
Network Bullet CameragQuick Start Guide 3. Install the dome drive to the adapter plate. Figure 2-10 Fix the Dome Drive 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.