Network Bullet CameragQuick Start Guide 5. Tear off the protection film softly to complete the installation. l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.4 Wall Mounting Steps: 1. Install the wall bracket to the wall with the supplied screws in the wall bracket package. You need to purchases a wall bracket separately if wall mounting is adopted. Figure 2-12 Install Wall Bracket 2.
Network Bullet CameragQuick Start Guide Figure 2-13 Fix the Adapter Plate 3. Fix the dome drive to the wall bracket with the supplied screws. Figure 2-14 Install the Camera 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
Network Bullet CameragQuick Start Guide Figure 2-15 Install the Front Cover 5. Tear off the protection film softly to complete the installation. l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands. 2.5 Install the Micro SD Card This series of camera supports local storage, please refer to the following steps to install the micro SD card. Steps: 1. Remove the front cover by loosening the set screws on it.
Network Bullet CameragQuick Start Guide Figure 2-16 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera.
Network Bullet CameragQuick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Network Bullet CameragQuick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Bullet CameragQuick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet CameragQuick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2.
Network Bullet CameragQuick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet CameragQuick Start Guide Note: Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Bullet CameragQuick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet CameragQuick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Bullet CameragQuick Start Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1) 34
Network Bullet CameragQuick Start Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
