If the QR Code is missing from this space, please scan the QR Code on the actual product. Scan the QR code with the Hik-Connect App to add the device to your account. Please keep it for further reference.
COPYRIGHT © 2020–2021 Hikvision USA Inc. and Hikvision Canada Inc. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Software Co., Ltd. (hereinafter referred to as “Hikvision”). This user manual (hereinafter referred to as “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Regulatory Information FCC Compliance Statement FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p.
Quick Setup Get the Hik-Connect App Power Kit Installation Doorbell Installation Doorbell Setup
Box Contents Doorbell (x1) Mounting Plate (x2) Pick the one for best surveillance angle. Plate Foam (x1) Stabilize the mounting plate when installing it on the rough surface.
Basics Terminals MicroSD Card Slot (Behind the cover) Speaker Name Description LED Indicator Red • Solid Red: Doorbell is starting up. • Fast-flashing Red: Doorbell exception (e.g. MicroSD card error). Blue • Solid Blue: Doorbell is functioning properly. • Fast-flashing Blue: Doorbell is ready for Wi-Fi connection. MicroSD Card (sold separately) Initialize the card in the Hik-Connect app before using it. Reset Button Hold for 5 secs to reset and enter Wi-Fi configuration mode.
Wiring Overview Hikvision doorbell with chime If you have a mechanical chime or electronic chime installed in your home, install the power kit and doorbell, and connect the wires as shown in the figure below. Hikvision doorbell with no chime If no chime is installed, skip power kit installation, install the doorbell, and connect the wires as shown in the figure below. • We recommend installing a new transformer to bring the output 12 to 24 volts.
Power Kit Installation The power kit ensures that your doorbell gets the power it needs, so be sure to install it before you install your Doorbell. 1 Shut off the electricity at the breaker that controls doorbell’s circuit. 2 Insert one end of the wire harness into the power kit. 3 Remove the cover from your mechanical chime. 4 Remove the existing chime wires in the terminals named TRANS and FRONT.
5 Connect the wire harness to the chime’ chime’s terminals named TRANS and FRONT. 6 Insert the existing chime wire and the other end of the wire harness into the wire connector and twist it tightly. Repeat this step with the other chime wire. Wire Connector Chime Wire Wire Harness 7 Mount the power kit to the side of the chime. 8 Replace the chime cover.
Doorbell Installation Recommended Installation Height: 1.2 m (4 ft) above the ground. off the electricity at the breaker that controls doorbell’ doorbell’s 1 Shut circuit. If the wall is uneven, paste the plate foam to the 2 (Optional) mounting plate. 3 Using your mounting plate as a template, mark the location of the two mounting holes on your wall, and insert anchors, then fix the mounting plate to the wall. Mounting Screw Anchor Recommended Hole Depth: 25 mm to 30 mm (1 inch to 1.2 inch).
4 If you have a chime installed, follow Option A; If not, follow Option B. Option A Connect doorbell to your existing doorbell wires. Fixing Screw U-Shaped Wire Power Supply: 12 to 24 VAC Option B Connect the fuse wire to your existing doorbell wire. Fuse Wire Fixing Screw Power Supply: 12 to 24 VAC 5 Install the doorbell to the mounting plate.
6 Insert the security screw into the top of the mounting plate to secure the doorbell. 7 Restore the electricity at the breaker. Doorbell is powered on when its indicator flashes blue quickly. If not, make sure your electricity is off and check the wiring. If yes, proceed to doorbell setup. Doorbell Setup 1 Add your doorbell to the Hik-Connect app. 1. Remove the faceplate of the doorbell.
2. Log in to your Hik-Connect account. 3. On the Home screen, tap “+” on the upper-right corner to go to the Scan QR Code interface. 4. Scan the QR code on the device (or on the front cover of this manual) when the indicator flashes blue. 5. Follow the wizard to add the doorbell to the Hik-Connect app. If you want to change the Wi-Fi that your doorbell has connected to, press and hold the reset button for 5s and repeat this part. 6. Put the faceplate back. 2 Choose the corresponding chime type. 1.
Install the MicroSD Card (Optional) 1. Remove the cover on the side of the doorbell with the screwdriver. 2. Insert a microSD card (sold separately) into the slot until there is a click. 3. Place the cover back on, and tighten the screws with the screwdriver. After installing the microSD card, you should initialize the card in the Hik-Connect app before using it. Initialize MicroSD Card 1. In the Hik-Connect app, tap the Storage Status in the Device Settings interface to check the microSD card status.
Troubleshooting 1 I have installed my doorbell, but the chime in my home doesn’t function. Please confirm the following details. 1. Make sure the right input voltage range (12V to 24V) has been used. Your doorbell is designed to work with at least 12 volts of AC power, which is in line with a majority of standard doorbell systems. Doorbell running at a lower voltage (or running on DC rather than AC) may cause chime malfunction. 2.
LIMITED WARRANTY Thank you for purchasing Hikvision products. This limited warranty (“warranty”) gives you, the original purchaser of the Hikvision product, specific legal rights. You may also have other legal rights that vary by state, province or jurisdiction. This warranty applies only to the original purchaser of the product. “Original purchaser” means any consumer having purchased the Hikvision product from an authorized seller.