Camera Network Cube Camera Quick Start Guide UD01798B 0
Network Cube Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Cube Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Cube Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network Cube Camera·Quick Start Guide FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Cube Camera·Quick Start Guide supplier or to a designated collection point. For more information see:www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s).
Network Cube Camera·Quick Start Guide gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Network Cube Camera·Quick Start Guide Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Cube Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Network Cube Camera·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. ● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Network Cube Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 2 Notice ........................................................................................... 15 3 Installation .................................................................................... 17 3.1 Micro SD Card Installation ............................................. 18 3.2 Stand Mounting .........................................................
Network Cube Camera·Quick Start Guide 1 Appearance Description There are two types of appearances for 24 series camera. Please refer to the figure below. And one appearance will be taken as an example in the chapter below.
Network Cube Camera·Quick Start Guide 1 4 7 2 3 5 6 8 11 12 13 14 9 10 15 Figure 1-3 Overview 12
Network Cube Camera·Quick Start Guide Table 1-1 Description No. Description 1 Lens 2 Microphone 3 IR LED Alarm: Solid red when the camera is armed; Solid blue when the camera is unarmed.
Network Cube Camera·Quick Start Guide No. Description 12 O: Alarm Output Interface 13 Power supply interface (12 VDC) 14 Speaker Note: Press RESET about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. A wireless router with the WPS function is required to enable the WPS function of the camera. Refer the steps below. Steps: 1. Press the WPS button on the router. 2.
Network Cube Camera·Quick Start Guide 2 Notice Do not install the camera in the extreme whether condition. Do not touch the lens with your finger. Do not install the camera towards the strong light or in the unstable lightening condition. Do not subject the camera to vibration, shock or heavy pressure.
Network Cube Camera·Quick Start Guide High humidity may damage the camera hardware; put it in dry and well-ventilated place. Under no circumstances should you submerge the camera in any type of liquid. Electromagnetic radiation may affect the video data transmission and the image quality.
Network Cube Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Cube Camera·Quick Start Guide 3.1 Micro SD Card Installation This series of camera supports micro SD card installation. Follow the steps below to install the micro SD card. 1. 2. Insert the micro SD card into the card slot on the side of the camera. (Optional) Push the inserted SD card to get it sprung out. Micro SD Figure 3-1 Install Micro SD Card 3.2 Stand Mounting Steps: 1. Take the bracket out from the package.
Network Cube Camera·Quick Start Guide Figure 3-2 Bracket 2. Align the camera body to the bracket, and rotate the camera body to fix it with the bracket. Figure 3-3 Install the Camera Body 3. Assemble the camera as the steps above, and put the camera on the flat surface.
Network Cube Camera·Quick Start Guide 3.3 Ceiling Mounting 1. Drill the screw holes according to the drill template. Drill Template 1 1 Screw hole All:for Mounting Base Figure 3-4 Drill Template 2. Disassemble the 3-axis bracket. Hold the base with one hand, and rotate the pole anticlockwise to disassemble the pole from the base.
Network Cube Camera·Quick Start Guide Knob Pole Base Fixed Tray Figure 3-5 Disassemble the Bracket 3. 4. Install the fixed tray to the ceiling with the supplied screws. Install the base to the fixed plate. Figure 3-6 Install the Fixed Plate and Mounting Base 5. Install the camera to the bracket.
Network Cube Camera·Quick Start Guide Figure 3-7 Install the Camera 6. Adjust surveillance angel 1). Loosen the knob to adjust the panning position and tilting position. 2). After adjusting the angle of the camera to the desired position, fasten the knob.
Network Cube Camera·Quick Start Guide 4 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 4.
Network Cube Camera·Quick Start Guide 4.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 4.2.
Network Cube Camera·Quick Start Guide 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Cube Camera·Quick Start Guide Figure 4-4 SADP Interface Note: The SADP software supports activating the camera in batch. Please refer to the user manual of SADP software for details. 3. Create a password and input the password in the password field, and confirm the password.
Network Cube Camera·Quick Start Guide You can check whether the activation is completed on the popup window. If activation failed, please make sure that the password meets the requirement and try again. 4.3 Modifying the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP software or client software to search and change the IP of network camera.
Network Cube Camera·Quick Start Guide Figure 4-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Cube Camera·Quick Start Guide 5 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Cube Camera·Quick Start Guide 4. Click Login. Figure 5-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 5-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
Network Cube Camera·Quick Start Guide 6 Operating via Hik-Connect App 6.1 Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 6.2 Adding Device to Hik-Connect Steps: 1. Use a network cable to connect the device with a router if the device does not support Wi-Fi.
Network Cube Camera·Quick Start Guide Figure 6-2 Scan QR Code 3. Follow the prompts to set the network connection and add the device to your Hik-Connect account. 6.3 Initializing the Memory Card Steps: 1. Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
0