Camera Network PT Dome Camera Quick Start Guide UD.
Network PT Dome Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network PT Dome Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network PT Dome Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Network PT Dome Camera·Quick Start Guide This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Network PT Dome Camera·Quick Start Guide mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s).
Network PT Dome Camera·Quick Start Guide gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Network PT Dome Camera·Quick Start Guide ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network PT Dome Camera·Quick Start Guide ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time. ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
Network PT Dome Camera·Quick Start Guide ● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Network PT Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 12 1.1 Overview ....................................................................... 12 1.2 Installing the Micro SD Card .......................................... 13 1.3 WPS Connection............................................................ 15 2 Installation .................................................................................... 16 2.
Network PT Dome Camera·Quick Start Guide 1 Appearance Description Please refer to the chapter below to have a close eye on the camera appearance and components. 1.
Network PT Dome Camera·Quick Start Guide Table 1-1 Description No. Description 1 Power Supply Interface (12 VDC) 2 Audio In/Out 3 Alarm In/Out 4 10M / 100M self-adaptive Ethernet interface & PoE 5 Micro SD/ SDHC/SDXC card slot 6 WPS (Wi-Fi Protected Setup) / Reset Button The figures shown in this manual are for reference only. The appearance and interfaces of the camera are subject to the actual model. 1.2 Installing the Micro SD Card Steps: 1.
Network PT Dome Camera·Quick Start Guide RST/WPS Micro SD Figure 1-3 Install the SD Card Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., and so on. 4. Move the cover back and press to secure the cover.
Network PT Dome Camera·Quick Start Guide 1.3 WPS Connection A wireless router with the WPS function is required to if you want to enable the WPS function of the camera. Follow the steps below to establish a WPS connection. 1. Press the WPS button on the router. 2. Press the WPS button (about 2s) on the camera within 120s you enable the WPS of the router to join in the wireless network. The WPS button works as a reset button only when you press it when the camera is powering on.
Network PT Dome Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network PT Dome Camera·Quick Start Guide 2.1 Ceiling Mounting Steps: 1. Stick the supplied drill template on the ceiling. 2. Drill the cable hole and screw holes according to the drill template. 3. Hammer the expansion plugs to the screw holes. FRONT 1 1 Drill Template Hole A: for cables routed through the ceiling Screw hole 1: for Mounting Base A 1 Figure 2-1 Drill Template 4. Rotate the adapter plate counterclockwise on the bottom of the camera to remove the adapter plate. 5.
Network PT Dome Camera·Quick Start Guide Front LO LOC K CK Joint Figure 2-2 Adapter Plate Figure 2-3 Install the Adapter Plate 18
Network PT Dome Camera·Quick Start Guide 6. Route the cables through the cable hole and connect the corresponding cables including power cable, network cable, alarm cables, and audio cables. 7. Align the notches on the camera with those on the adapter plate, and rotate the camera clockwise to secure the camera with the adapter plate. OPEN LOCK Figure 2-4 Connect the Cables 8. Power on the camera, visit the camera via web browser, and adjust the surveillance angle via the PTZ interface.
Network PT Dome Camera·Quick Start Guide Figure 2-5 PTZ Control Interface 0°~ 75° -90°~ +90° Figure 2-6 Adjust Surveillance Angel 20
Network PT Dome Camera·Quick Start Guide 2.2 Ceiling Mounting with a Junction Box You have to buy a junction box separately if you want to install the camera with a junction box. Steps: 1. Stick the drill temperate to the ceiling. 2. Drill the screw holes and cable hold according to the drill temperate. 3. Hammer the expansion plugs to the screw holes. 4. Fix the junction box to the ceiling with screws. FRONT 1 1 Drill Template Screw hole 1: for Mounting Base Please use Φ5.
Network PT Dome Camera·Quick Start Guide Figure 2-8 Hammer the Screws 6. Align two joints of the junction box to the two inserted screws, and rotate the junction box counterclockwise to fix the junction box. 7. Use the other two screws to secure the junction box.
Network PT Dome Camera·Quick Start Guide 8. Connect the power cable, network cable, alarm cable and audio cable. 9. Align the notches on the camera with the joints on the junction box, and rotate the camera clockwise to secure the camera. Side Outlet OPEN LOCK Figure 2-10 Fix the Camera 10. Adjust the surveillance angle according to step 8 of chapter 2.1. 2.3 Wall Mounting You have to buy a wall mount separately if you select wall mounting. 1. Install the wall mounting to the wall.
Network PT Dome Camera·Quick Start Guide 2. Rotate the adapter plate counterclockwise on the bottom of the camera to remove the adapter plate. 3. Fix the adapter plate to the wall mount with the supplied screws. Align the No.2 screw holes on the adapter plate with the No.2 screw holes on the wall mount, and align the cable holes as well when installing the adapter plate. Figure 2-11 Install the Adapter Plate 4. Connect the power cable, network cable, alarm cable and audio cable. 5.
Network PT Dome Camera·Quick Start Guide OPEN LOCK Figure 2-12 Install the Camera 6. Align the bracket base to the wall, and hammer the expansion plugs to the wall. 7. Fix the bracket base with the supplied expansion screws.
Network PT Dome Camera·Quick Start Guide Bracket Base Figure 2-13 Fix the Bracket Base to the Wall 8. Route the cables. 9. Fix the camera to the bracket base with the supplied screws in the wall mount package. Figure 2-14 Fix the Camera 10. Adjust the surveillance angle according to step 8 of chapter 2.1.
Network PT Dome Camera·Quick Start Guide 2.4 Routing the Cable through Side Outlet You may select to route the cables through the side outlet, please follow the steps below. 1. Pull up the cap of the wiring duct to remove the cap. Cap Side Outlet Figure 2-15 Remove the Cap 2. Route the cables through the side outlet.
Network PT Dome Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Network PT Dome Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network PT Dome Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network PT Dome Camera·Quick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2.
Network PT Dome Camera·Quick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network PT Dome Camera·Quick Start Guide Note: Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network PT Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network PT Dome Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network PT Dome Camera·Quick Start Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1) 36
Network PT Dome Camera·Quick Start Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
0
