Fingerprint Card Reader User Manual
Fingerprint Card Reader User Manual User Manual About this Manual This manual is applicable for fingerprint card reader. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website.
Fingerprint Card Reader User Manual security controls, conduct periodic reviews and assessments of the effectiveness of your security controls. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Fingerprint Card Reader User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Fingerprint Card Reader User Manual Model Manufacturer Standard DSA-12PFT-12FIN 120100 Dee Van Enterprise Co., Ltd. IS DSA-12PFT-12FUS 120100 Dee Van Enterprise Co., Ltd. IEC DSA-12PFT-12 FBZ 120100 Dee Van Enterprise Co., Ltd. NBR Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
Fingerprint Card Reader User Manual Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
Fingerprint Card Reader User Manual Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use.
Fingerprint Card Reader User Manual Content Chapter 1 1.1 1.2 Chapter 2 2.1 2.2 2.3 2.4 Chapter 3 Introduction ........................................................... 3 Product Overview ..................................................... 3 Product Appearance ................................................. 3 Installation ............................................................. 5 Introduction for DIP Switch....................................... 5 Definition of Cable ...........................
Fingerprint Card Reader User Manual Chapter 1 Introduction 1.1 Product Overview Fingerprint and card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via the RS-485 protocol. And a built-in tamper-proof module helps to protect card reader from malicious damage. NFC tag anti-cloning is also supported. 1.
Fingerprint Card Reader User Manual Table 1-1 Components Description No. Name 1 Fingerprint Scanner 2 Cable Interface of RS-485, Power, LED Control, etc.
Fingerprint Card Reader User Manual Chapter 2 Installation 2.1 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 4, representing the RS-485 address. Figure 2-1 DIP Switch Module Table 1-2 Description of DIP Switch Icon Description 1 Represent ON in binary mode 0 Represent OFF in binary mode For example, the binary value of the following status is 1100.
Fingerprint Card Reader User Manual 2.2 Definition of Cable The description of 5 cables is shown below. Table 1-3 Description of Cables Color Blue Yellow Red Black Black Description RS-485 RS-485 + PWR (DC +12V) GND (Power Grounding) GND (RS-485 Grounding) 2.3 Wiring Cables Purpose: Wire the cables between the controller and the card reader, thus to establish the communication between them. Steps for RS-485 communication mode: 1. Set the DIP switch for RS-485 address. For Details, refer to 2.
Fingerprint Card Reader User Manual Figure 2-3 Wiring for RS-485 Communication Mode 2.4 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 2.1 Introduction for DIP Switch.
Fingerprint Card Reader User Manual 1. Fix the mounting plate on the wall with 2 provided screws. Note: Do not warp the mounting plate when installing. 2. Connect the cables between controller and card reader. For details, refer to 2.3 Wiring Cables. Unscrew the screw at the bottom of the card reader. Buckle the card reader up to the plate. 3. 4. 5. Fasten the card reader to the plate with the set screw.
Fingerprint Card Reader User Manual Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn green and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information.
Fingerprint Card Reader User Manual LED Indicator Status Solid green for 2s Solid red Red and blink for 3 times Red and blinking Description prompt for pressing the fingerprint after swiping the card. The operation of configuring the fingerprint. The operation of swiping card is valid. Card reader is working normally. The operation of swiping card is invalid. For RS-485 protocol: Registering failed or card reader is offline.
Fingerprint Card Reader User Manual Appendix: Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
Fingerprint Card Reader User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
Fingerprint Card Reader User Manual UD22705N 13
