DS-K1201A Series Fingerprint Card Reader User Manual
DS-K1201 Fingerprint Card Reader User Manual © 2021 Hangzhou Hikvision Digital Technology Co., Ltd. This manual is applied to fingerprint card reader. Device Name Model DS-K1201AMF Fingerprint Card Reader DS-K1201AEF It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual The Manual includes instructions for using and managing the product.
DS-K1201 Fingerprint Card Reader SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Support Should you have any questions, please do not hesitate to contact your local dealer.
DS-K1201 Fingerprint Card Reader Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1201 Fingerprint Card Reader documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
DS-K1201 Fingerprint Card Reader If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
DS-K1201 Fingerprint Card Reader Content Chapter 1 Introduction...................................................................................... 1 1.1 Product Overview ........................................................................................... 1 1.2 Product Appearance ....................................................................................... 1 Chapter 2 Installation........................................................................................ 2 2.
DS-K1201 Fingerprint Card Reader Chapter 1 Introduction 1.1 Product Overview Fingerprint and card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via the RS-485 protocol. And a built-in tamper-proof module helps to protect card reader from malicious damage. NFC tag anti-cloning is also supported. 1.2 Product Appearance 2 3 1 Figure 1-1 Front View Figure 1-2 Rear View Table 1-1 Components Description No.
DS-K1201 Fingerprint Card Reader Chapter 2 Installation 2.1 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 to 4, representing the RS-485 address. Figure 2-1 DIP Switch Module Table 1-2 Description of DIP Switch Icon Description 1 Represent ON in binary mode 0 Represent OFF in binary mode For example, the binary value of the following status is 1100.
DS-K1201 Fingerprint Card Reader 2.3 Wiring Cables Purpose: Wire the cables between the controller and the card reader, thus to establish the communication between them. Steps for RS-485 communication mode: 1. Set the DIP switch for RS-485 address. For Details, refer to 2.1 Introduction for DIP Switch. 2. Wire the cable between the controller and the card reader as shown below. Figure 2-3 Wiring for RS-485 Communication Mode 2.4 Installing Card Reader Before you start: Set the DIP switch.
DS-K1201 Fingerprint Card Reader 2. Connect the cables between the controller and the card reader. For details, refer to 2.3 Wiring Cables. 3. Unscrew the screw at the bottom of the card reader. 4. Buckle the card reader up to the plate. 5. Fasten the card reader to the plate with the set screw.
DS-K1201 Fingerprint Card Reader Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn green and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information.
DS-K1201 Fingerprint Card Reader Table 1-5 Description of LED Indicator LED Indicator Status Description Green (blink for 1 time), and red (blink The card reader is power on. for 3 times) For Card + Fingerprint authentication: prompt for pressing the fingerprint after Green and blinking swiping the card. The operation of configuring the fingerprint. Solid green for 2s The operation of swiping card is valid. Solid red Card reader is working normally.
DS-K1201 Fingerprint Card Reader Appendix Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
8 UD22704B
