User's Manual
Table Of Contents
- Legal Information
- Symbol Conventions
- Regulatory Information
- Safety Instruction
- Available Models
- Chapter 1 Overview
- Chapter 2 Appearance
- Chapter 3 Installation
- Chapter 4 Device Wiring
- Chapter 5 Activation
- Chapter 6 Quick Operation
- Chapter 7 Basic Operation
- 7.1 Login
- 7.2 Communication Settings
- 7.3 Local Time and Attendance
- 7.4 Local Time and Attendance Settings
- 7.5 Data Management
- 7.6 Identity Authentication
- 7.7 Basic Settings
- 7.8 Set Biometric Parameters
- 7.9 System Maintenance
- Chapter 8 Configure the Device via the Mobile Browser
- 8.1 Login
- 8.2 Search Event
- 8.3 Configuration
- 8.3.1 View Device Information
- 8.3.2 Time Settings
- 8.3.3 Set DST
- 8.3.4 Network Settings
- 8.3.5 Set Time and Attendance via Mobile Web Browser
- 8.3.6 Set Privacy Parameters
- 8.3.7 Set Authentication Parameters
- 8.3.8 Face Parameters Settings
- Chapter 9 Operation via Web Browser
- 9.1 Login
- 9.2 Person Management
- 9.3 Search Event
- 9.4 Configuration
- 9.4.1 Set Local Parameters
- 9.4.2 View Device Information
- 9.4.3 Set Time
- 9.4.4 Set DST
- 9.4.5 View Open Source Software License
- 9.4.6 Upgrade and Maintenance
- 9.4.7 Security Mode Settings
- 9.4.8 Certificate Management
- 9.4.9 Change Administrator's Password
- 9.4.10 Online Users
- 9.4.11 View Device Arming/Disarming Information
- 9.4.12 Network Settings
- 9.4.13 Set Video and Audio Parameters
- 9.4.14 Customize Audio Content
- 9.4.15 Time and Attendance Settings
- 9.4.16 Access Control Settings
- 9.4.17 Title: Local Time and Attendance Settings
- 9.4.18 Set Biometric Parameters
- 9.4.19 Set Notice Publication
- Appendix A. Tips for Installation Environment
- Appendix B. Tips for Scanning Fingerprint
- Appendix C. Tips When Collecting/Comparing Face Picture
- Appendix D. Attendance Capacity
- Appendix E. Attendance Report Table
- Chapter 10 Dimensions
- Appendix F. Communication Matrix and Device Command
Cauons:
• Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnesm
radiaon. Avoid the equipment installaon on vibraons surface or places
subject to shock (ignorance can cause equipment damage).
• Do not place the device in extremely hot (refer to the specicaon of the device for the detailed
operang temperature), cold, dusty or damp locaons, and do not expose it to high
electromagnec radiaon.
• Exposing the equipment to direct sun light, low venlaon or heat source such as heater or
radiator is forbidden (ignorance can cause re danger).
• The device cover for indoor use shall be kept from rain and moisture.
• Exposing the equipment to direct sun light, low venlaon or heat source such as heater or
r
adiator is forbidden (ignorance can cause re danger).
• Please use a so and dry cloth when clean inside and outside surfaces of the device cover, do
not use alkaline detergents.
• Biometric recognion products are not 100% applicable to an-spoong environments. If you
require a higher security level, use mulple authencaon modes.
• The serial port of the equipment is used for debugging only.
• Install the equipment according to the instrucons in this manual. To prevent injury, this
equipment must be securely aached to the
oor/wall in accordance with the installaon
instrucons.
• Improper use or replacement of the baery may result in hazard of explosion. Replace with the
same or equivalent type only. Dispose of used baeries according to the instrucons provided by
the
baery manufacturer.
• This bracket is intended for use only with equipped devices. Use with other equipment may
result in instability causing injury.
• This equipment is for use only with equipped bracket. Use with other (carts, stands, or carriers)
may result in instability causing injury.
DS-K1A340 Series Face Time Aendance Terminal User Manual
vii