DS-K1T321 Series Face Recognition Terminal
DS-K1T321 Series Face Recognition Terminal Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T321 Series Face Recognition Terminal DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T321 Series Face Recognition Terminal Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T321 Series Face Recognition Terminal Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T321 Series Face Recognition Terminal under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T321 Series Face Recognition Terminal Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T321 Series Face Recognition Terminal Cautions: ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T321 Series Face Recognition Terminal Available Models Product Name Face Recognition Terminal Model Wireless DS-K1T321MFX 13.56 MHz Card Presenting Frequency DS-K1T321MWX 13.56 MHz Card Presenting Frequency, WiFi, 2.4G DS-K1T321MFW 13.56 MHz Card Presenting Frequency, WiFi, 2.4G DS-K1T321EX 125 KHz Card Presenting Frequency DS-K1T321EFX 125 KHz Card Presenting Frequency DS-K1T321EWX 125 KHz Card Presenting Frequency, WiFi, 2.4G DS-K1T321EFWX 125 KHz Card Presenting Frequency, WiFi, 2.
DS-K1T321 Series Face Recognition Terminal Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features ................................................................................................................................. 1 Chapter 2 Appearance ...........
DS-K1T321 Series Face Recognition Terminal 7.1.2 Login by Activation Password ...................................................................................... 25 7.1.3 Forgot Password .......................................................................................................... 25 7.2 Communication Settings ...................................................................................................... 25 7.2.1 Set Wired Network Parameters ............................................
DS-K1T321 Series Face Recognition Terminal 7.9.3 Set Auto Attendance via Device .................................................................................. 48 7.9.4 Set Manual and Auto Attendance via Device .............................................................. 50 7.10 System Maintenance .......................................................................................................... 52 Chapter 8 Configure the Device via the Mobile Browser ............................................
DS-K1T321 Series Face Recognition Terminal 10.2 Forget Password ................................................................................................................. 79 10.3 Live View ............................................................................................................................ 79 10.4 Person Management .......................................................................................................... 81 10.5 Search Event .....................................
DS-K1T321 Series Face Recognition Terminal 11.2.1 Add Device .............................................................................................................. 109 11.2.2 Reset Device Password ........................................................................................... 111 11.2.3 Manage Added Devices .......................................................................................... 112 11.3 Group Management ..................................................................
DS-K1T321 Series Face Recognition Terminal Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● 2.
DS-K1T321 Series Face Recognition Terminal Chapter 2 Appearance The appearance of the device with fingerprint is as follows: Figure 2-1 Appearance The appearance of the device without fingerprint is as follows: Table 2-1 Appearance Description No.
DS-K1T321 Series Face Recognition Terminal No. Name Note Only devices that support the fingerprint function contain a fingerprint module.
DS-K1T321 Series Face Recognition Terminal Chapter 3 Installation 3.1 Installation Environment ● ● ● ● Indoor use only. Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight. 3.2 Install with Gang Box Steps 1. Make sure the gang box is installed on the wall. Note You should purchase the gang box separately.
DS-K1T321 Series Face Recognition Terminal Figure 3-2 Install Mounting Plate 3. Route the cable through the cable hole, wire the cables and insert the cables in the gang box.
DS-K1T321 Series Face Recognition Terminal Figure 3-3 Apply Silicone Sealant 4. Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw (SC-CM4X14-5T10-SUSS).
DS-K1T321 Series Face Recognition Terminal Figure 3-4 Secure Device 3.3 Surface Mounting Steps Note The additional force shall be equal to three times the weight of the equipment. The equipment ad its associated mounting means shall remain secure during the installation. After the installation, the equipment, including any associated mounting plate, shall not be damaged. 1. Secure the mounting plate on the wall with the 4 supplied screws (SC-KA4X22).
DS-K1T321 Series Face Recognition Terminal Figure 3-5 Install Mounting Plate 2. Route the cable through the cable hole of the mounting plate, and connect to corresponding peripherals cables. Note If the device is installed outdoor, you should apply silicone sealant to the wiring exit to avoid water from entering.
DS-K1T321 Series Face Recognition Terminal Figure 3-6 Apply Silicone Sealant 3. Align the device with the mounting plate and hang the device on the mounting plate. Use 1 supplied screw (SC-CM4X14_5T10-SUSS) to secure the device and the mounting plate.
DS-K1T321 Series Face Recognition Terminal Figure 3-7 Hang Device 4. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.4 Base Mounting Steps 1. Route the cables through the cable hole of the bracket, and connect the terminals with peripherals cables. Place the bracket close to the back side of the device. Figure 3-8 Place Bracket Close to Device Back Side 2.
DS-K1T321 Series Face Recognition Terminal Figure 3-9 Fasten Bracket 3. Buckle into the bracket to the end to complete the installation.
DS-K1T321 Series Face Recognition Terminal Chapter 4 Wiring You can connect the NC/NO and COM terminal with the door lock, connect the SEN and GND terminal with the door contact and the BTN/GND terminal with the exit button. ● ● ● ● Note If cable size is 18 AWG, you should use a 12 V power supply. And the distance between the power supply and the device should be no more than 20 m. If the cable size is 15 AWG, you should use a 12 V power supply.
DS-K1T321 Series Face Recognition Terminal 4.2 Wire Normal Device You can connect the terminal with normal peripherals. Figure 4-1 Device Wiring ● ● ● Note Do not wire the device to the electric supply directly. When connecting door contact and exit button, the device should use the same common ground connection.
DS-K1T321 Series Face Recognition Terminal Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T321 Series Face Recognition Terminal Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T321 Series Face Recognition Terminal Note Characters containing admin and nimda are not supported to be set as activation password. 3. Click Activate. 4. Edit the device IP address. You can edit the IP address via the SADP tool, the device, and the client software. 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.
DS-K1T321 Series Face Recognition Terminal Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T321 Series Face Recognition Terminal Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T321 Series Face Recognition Terminal Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English.
DS-K1T321 Series Face Recognition Terminal Note After you change the system language, the device will reboot automatically. 6.2 Set Network Parameters After activation and select application mode, you can set the network for the device Steps 1. When you enter the Select Network page, select Wired Network or Wi-Fi for your actual needs. Figure 6-2 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Select Next. Wired Network Note Make sure the device has connected to a network.
DS-K1T321 Series Face Recognition Terminal If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or select Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Select Back to skip network settings. 6.3 Access to Platform Enable the function and the device can communicate via Hik-Connect. You can add the device to Hik-Connect modile client and so on. Steps 1.
DS-K1T321 Series Face Recognition Terminal Figure 6-3 Privacy Upload Pic. When Auth. (Upload Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Pic. When Auth. (Save Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device. Save Registered Pic. (Save Registered Picture) The registered face picture will be saved to the system if you enable the function. Upload Pic.
DS-K1T321 Series Face Recognition Terminal Steps 1. Enter the administrator's name (optional) and select Next. Figure 6-4 Add Administrator Page 2. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Press OK to capture and press OK to confirm. : Press your finger according to the instructions on the device screen. Press OK to confirm. : Enter the card No. or present card on the card presenting area.
DS-K1T321 Series Face Recognition Terminal Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long press OK to enter the admin login page. Figure 7-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
DS-K1T321 Series Face Recognition Terminal 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long press OK to enter Authenticate via Admin page. to enter the password. 2. Press - If you have added an administrator for the device, press OK and enter the password. - If you haven't added an administrator for the device, enter the password. 3.
DS-K1T321 Series Face Recognition Terminal Figure 7-2 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually. Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server.
DS-K1T321 Series Face Recognition Terminal 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Select Basic → Comm. (Communication) to enter the Communication settings page. 2. On the Communication settings page, select Wi-Fi.
DS-K1T321 Series Face Recognition Terminal 3. Enable the Wi-Fi function. 4. Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically. - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6.
DS-K1T321 Series Face Recognition Terminal Figure 7-4 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group. Main Channel Support N1 or None. ISUP Enable ISUP function and the data will be uploaded via ISUP protocol.
DS-K1T321 Series Face Recognition Terminal Address Type Select an address type according to your actual needs. IP Set the ISUP server's IP address. Port Set the ISUP server's port No. Note Port No. Range: 1 to 65535. Device ID Set device serial no. ISUP Key If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only. ● ● Note Remember the ISUP account and ISUP key.
DS-K1T321 Series Face Recognition Terminal 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Select User → Add User to enter the Add User page. 3. Edit the employee ID.
DS-K1T321 Series Face Recognition Terminal Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Select the Name field and input the user name on the keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 128 characters are allowed in the user name. 5.
DS-K1T321 Series Face Recognition Terminal 1. Long press OK and login the device. 2. Select User → Add User to enter the Add User page. 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Select the Name field and input the user name on the keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name.
DS-K1T321 Series Face Recognition Terminal Figure 7-5 Add Face Picture 6. Look at the camera. ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the center of the page. 7.
DS-K1T321 Series Face Recognition Terminal 8. Optional: Press ESC to select Retake and adjust your face position to add the face picture again. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 10. Press ESC and then press OK to save the settings. 7.3.
DS-K1T321 Series Face Recognition Terminal For details about the instructions of scanning fingerprints, see Tips for Scanning Fingerprint . 7. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 8. Press ESC and then press OK to save the settings. 7.3.
DS-K1T321 Series Face Recognition Terminal Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 7. Configure the card type. 8. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 9.
DS-K1T321 Series Face Recognition Terminal The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. 7. Press ESC and then press OK to save the settings. 7.3.
DS-K1T321 Series Face Recognition Terminal 7.4.1 Delete Data Delete user data. On the Home page, select Data → Delete Data → User Data . All user data added in the device will be deleted. 7.4.2 Import Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Import Data . 3. Tap User Data, Face Data or Access Control Parameters . Note The imported access control parameters are configuration files of the device. 4. Enter the created password when you exported the data.
DS-K1T321 Series Face Recognition Terminal Note The exported access control parameters are configuration files of the device. 4. Optional: Create a password for exporting. When you import those data to another device, you should enter the password. ● ● ● Note The supported USB flash drive format is DB. The system supports the USB flash drive with the storage of 1G to 32G. Make sure the free space of the USB flash drive is more than 512M. The exported user data is a DB file, which cannot be edited. 7.
DS-K1T321 Series Face Recognition Terminal Steps 1. If the authentication mode is Card and Face, Password and Face, Card and Password, Card and Face and Fingerprint, authenticate any credential according to the instructions on the live view page. Note ● The card can be normal IC card, or encrypted card. 2. After the previous credential is authenticated, continue authenticate other credentials. ● ● Note For detailed information about scanning fingerprint, see Tips for Scanning Fingerprint.
DS-K1T321 Series Face Recognition Terminal Figure 7-6 Basic Settings Page Voice Settings You can enable/disable the voice function. Time Settings Set the time zone, the device time and the DST. Sleeping (s) Set the device sleeping waiting time (s). For example, when you are on the initial page and if you set the sleeping time to 30 s, the device will sleep after 30 s without any operation.
DS-K1T321 Series Face Recognition Terminal Note 20 s to 999 s are available to configure. Select Language Select the language according to actual needs. Supplement Light Set the white light mode, brightness, start time and end time. Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance.
DS-K1T321 Series Face Recognition Terminal Parameter Description Face 1:N Security Level Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face 1:1 Security Level Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T321 Series Face Recognition Terminal Figure 7-7 Access Control Parameters The available parameters descriptions are as follows: Table 7-2 Access Control Parameters Descriptions Parameter Terminal Auth. Mode Description Select the face recognition terminal's authentication mode. You can also customize the authentication mode.
DS-K1T321 Series Face Recognition Terminal Parameter Description ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. If you adopt multiple authentication modes, you should authenticate other methods before authenticating face.
DS-K1T321 Series Face Recognition Terminal Figure 7-8 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode.
DS-K1T321 Series Face Recognition Terminal Figure 7-9 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication.
DS-K1T321 Series Face Recognition Terminal Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto. Figure 7-10 Auto Attendance Mode 3. Enable the Attendance Status Required function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required.
DS-K1T321 Series Face Recognition Terminal Note The attendance status will be valid within the configured schedule. Result When you authenticate on the initial page, the authentication will be marked as the configured attendance status according to the configured schedule. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.9.
DS-K1T321 Series Face Recognition Terminal Figure 7-11 Manual and Auto Mode 3. Enable the Attendance Status Required function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Select Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday.
DS-K1T321 Series Face Recognition Terminal select a status to take attendance manually, the authentication will be marked as the edited attendance status. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.10 System Maintenance You can view the device system information and capacity. You can also upgrade device, restore the system to factory settings, default settings, and reboot the system.
DS-K1T321 Series Face Recognition Terminal You can view the number of user, face picture, card, and event. Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details. Device Upgrade Plug the USB flash drive in the device USB interface. Select Upgrade → OK , and the device will read the digicap.dav file in the USB flash drive to start upgrading. Restore to Factory Settings All parameters will be restored to the factory settings.
DS-K1T321 Series Face Recognition Terminal Chapter 8 Configure the Device via the Mobile Browser 8.1 Login You can login via mobile browser. ● ● Note Parts of the model supports Wi-Fi settings. Make sure the device is activated. Obtain the IP address from the device after Wi-Fi is enabled. Make sure the IP segment of the device and the computer is the same. For details, refers to Set Wi-Fi Parameters .
DS-K1T321 Series Face Recognition Terminal Figure 8-1 Add User 2) Set the following parameters. Employee ID Enter the employee ID. The employee ID cannot be 0 or exceed 32 characters. It can be a combination of uppercase, lowercase letters and numbers. Name Enter the name. The name supports numbers, uppercase and lowercase English, and characters. The name is recommended to be within 32 characters. Gender Select the gender. User Role Select your user role. Floor No./Room No. Enter the floor No./room No.
DS-K1T321 Series Face Recognition Terminal Fingerprint Add fingerprint. Tap Fingerprint, then tap +, and add fingerprint via the fingerprint module. Start Date/End Date Set Start Date and End Date of user permission. Administrator If the user needs to be set as administrator, you can enable Administrator. Authentication Type Set the authentication type. 3) Tap Save. 3. Tap the user that needs to be edited in the user list to edit the information. 4.
DS-K1T321 Series Face Recognition Terminal Figure 8-2 Device Information 57
DS-K1T321 Series Face Recognition Terminal You can view the device name, device No., language, model, serial No., version, device capacity, etc. 8.4.2 Time Settings Set the time zone, time sync. mode, and displayed time. Tap Configuration → System → System Settings → Time Settings to enter the settings page. Figure 8-3 Time Settings Tap Save to save the settings. Time Zone Select the time zone where the device is located from the drop-down list. Time Sync.
DS-K1T321 Series Face Recognition Terminal 8.4.3 Set DST Steps 1. Tap Configuration → System → System Settings → DST , to enter the settings page. Figure 8-4 DST 2. Tap Enable DST. 3. Set the start time, end time, and DST bias. 4. Tap Save.
DS-K1T321 Series Face Recognition Terminal 8.4.4 View Open Source Software License Tap Configuration → System → System Settings → About , and tap View Licenses to view the device license. 8.4.5 User Management Steps 1. Tap Configuration → System → User Management → admin → Modify Password to enter the setting page. 2. Enter the old password and create a new password. 3. Confirm the new password. 4. Tap OK. Note The password strength of the device can be automatically checked.
DS-K1T321 Series Face Recognition Terminal The device will restore to the default settings, except for the device IP address and the user information. Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Unlink Tap Configuration → System → Maintenance . Tap Unlink to unlink the app. After unlinking APP account, you cannot operate via APP. 8.4.7 Security Settings You can set the SSH and HTTP according to actual needs.
DS-K1T321 Series Face Recognition Terminal Figure 8-5 Wi-Fi 3. Add Wi-Fi. 1) Tap +. Figure 8-6 Add Wi-Fi 2) Enter Wi-Fi Name and Wi-Fi Password, and select Working Mode and Encryption Type.
DS-K1T321 Series Face Recognition Terminal 3) Tap Save. 4. Select the Wi-Fi name, and tap Connect. 5. Enter the password and tap Save. 6. Set WLAN parameters. 1) Set the IP address, subnet mask, and gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and gateway automatically. 2) Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 3) Tap Save.
DS-K1T321 Series Face Recognition Terminal Set the HTTPS for accessing the browser. Certificate is required when accessing. Server It refers to the port through which the client adds the device. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1. Tap Configuration → Network → Advanced → Hik-Connect to enter the settings page. Note Hik-Connect is an application for mobile devices.
DS-K1T321 Series Face Recognition Terminal The device will communicate with the center via the main channel. When exception occurs in the main channel, the device and the center will communicate with each other via the backup channel. 5. Tap Save to save the settings. HTTP Listening You can set the HTTP listening parameters. Steps 1. Tap Configuration → Network → Advanced → HTTP Listening . 2. Edit the destination IP or domain name, URL and port. 3.
DS-K1T321 Series Face Recognition Terminal Figure 8-7 Authentication Settings 2. Tap Save. Device Type Main Card Reader You can configure the device card reader's parameters. If you select main card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Minimum Card Swiping Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max.
DS-K1T321 Series Face Recognition Terminal If the interval between card presenting of the same card is less than the configured value, the card presenting is invalid. The interval time range is from 0 to 255 seconds (When set to 0, it means that recognition interval is not enabled, and the same authentication can be used for unlimited times). Authentication Interval You can set the authentication interval of the same person when authenticating.
DS-K1T321 Series Face Recognition Terminal The name information is desensitized with an asterisk. ID De-identification The ID information is desensitized with an asterisk. Picture Uploading and Storage You can upload and store pictures. Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically. Save Captured Picture When Authenticating If you enable this function, you can save the picture when authenticating to the device.
DS-K1T321 Series Face Recognition Terminal Figure 8-8 Card Security Set the parameters and tap Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption M1 card encryption can improve the security level of authentication. Sector Enable the function and set the encryption sector.
DS-K1T321 Series Face Recognition Terminal Figure 8-9 Card Authentication Page Select a card authentication mode and tap Save. Full Card No. All card No. will be read. Wiegand 26 (3 bytes) The device will read card via Wiegand 26 protocol (read 3 bytes). Wiegand 34 (4 bytes) The device will read card via Wiegand 34 protocol (read 4 bytes). 8.4.10 Face Parameters Settings Set face parameters. Face Parameters Settings Tap Configuration → Smart → Intelligent Parameter .
DS-K1T321 Series Face Recognition Terminal Figure 8-10 Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Set Face Parameters. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T321 Series Face Recognition Terminal Note If the device is not activated by other tools, the device uses indoor as the environment mode by default. Face Recognition Mode Normal Mode The device uses a camera to perform face recognition. The device uses a camera to perform face recognition. Continuous Face Recognition Interval (s) Set the time interval between two continuous face recognitions when authenticating. Note Value Range: 1 to 10.
DS-K1T321 Series Face Recognition Terminal Set the matching value when authenticating with face mask via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face with Mask 1:N Matching Threshold Set the matching threshold when authenticating with face mask via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T321 Series Face Recognition Terminal Figure 8-11 Door Parameters Settings Page Tap Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration.
DS-K1T321 Series Face Recognition Terminal You can set the door lock status when the door lock is powering off. By default, it is Remain Closed. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended access needs swipes her/his card. Door Remain Open Duration with First Person Set the door open duration when first person is in. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K1T321 Series Face Recognition Terminal Chapter 9 Quick Operation via Web Browser 9.1 Select Language You can select a language for the device system. Click in the top right of the web page to enter the Device Language Settings page. You can select a language for the device system from the drop-down list. By default, the system language is English. Note After you change the system language, the device will reboot automatically. Click Next to complete the settings. 9.
DS-K1T321 Series Face Recognition Terminal Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. Server Address/NTP Port/Interval You can set the server address, NTP port, and interval.
DS-K1T321 Series Face Recognition Terminal Click in the top right of the web page to enter the wizard page. After setting device language, time and environment, you can click Next to enter the Privacy Settings page. Picture Uploading and Storage Save Picture When Authenticating Save picture when authenticating automatically. Upload Picture When Authenticating Upload the pictures when authenticating to the platform automatically.
DS-K1T321 Series Face Recognition Terminal Chapter 10 Operation via Web Browser 10.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K1T321 Series Face Recognition Terminal Figure 10-1 Live View Page Function Descriptions: Door Status Click to view the device live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds.
DS-K1T321 Series Face Recognition Terminal You can capture image when starting live view. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Full screen view. / / / The door status is open/closed/remaining open/remaining closed. Controlled Status You can select open/closed/remaining open/remaining closed status according to your actual needs. Real-Time Event You can view the event Employee ID, Name, Card No., Event Type, Time, and Operation.
DS-K1T321 Series Face Recognition Terminal Add the person's basic information, including the employee ID, the person's name, the gender, and person type. If you select Visitor as the person type, you can set the visit times. Click Save to save the settings. Set Permission Time Click Person Management → Add to enter the Add Person page. Enable Long-Term Effective User, or set Start Time and End Time and the person can only has the permission within the configured time period according to your actual needs.
DS-K1T321 Series Face Recognition Terminal Click Save to save the settings. 10.5 Search Event Click Event Search to enter the Search page. Figure 10-2 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel.
DS-K1T321 Series Face Recognition Terminal 10.6 Configuration 10.6.1 Set Local Parameters Set the live view parameters, picture and clip settings. Set Live View Parameters Click Configuration → Local to enter the Local page. Configure the stream type, the play performance and click Save. Picture and Clip Settings Click Configuration → Local to enter the Local page. Select image format, saving path and click Save. You can also click Open to open the file folder to view details. 10.6.
DS-K1T321 Series Face Recognition Terminal Figure 10-3 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time.
DS-K1T321 Series Face Recognition Terminal Figure 10-4 DST Page 2. Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 10.6.5 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK. Caution The password strength of the device can be automatically checked.
DS-K1T321 Series Face Recognition Terminal your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 10.6.6 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → Arming/Disarming Information . You can view the device arming/disarming information.
DS-K1T321 Series Face Recognition Terminal If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, Mac address, and MTU. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, the IPv4 default gateway automatically. DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need. Set Wi-Fi Parameters Set the Wi-Fi parameters for device wireless connection.
DS-K1T321 Series Face Recognition Terminal Figure 10-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add and enter a Wi-Fi's name, password, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Set the IP address, subnet mask, and default gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and default gateway automatically. 5. Click Save.
DS-K1T321 Series Face Recognition Terminal Set Port Parameters Set the HTTP, HTTPS, HTTP Listening, RTSP and Server port parameters. Click Configuration → Network → Network Service → HTTP(S) . HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login. HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing.
DS-K1T321 Series Face Recognition Terminal Note 6 to 12 letters (a to z, A to Z) or numbers (0 to 9), case sensitive. You are recommended to use a combination of no less than 8 letters or numbers. 5. Click Save to enable the settings. Set ISUP Parameters Set the ISUP parameters for accessing device via ISUP protocol. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Device Access → ISUP . 2. Check Enable. 3.
DS-K1T321 Series Face Recognition Terminal Figure 10-7 Video Settings Page Set the stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, the video encoding, and I Frame Interval. Click Save to save the settings after the configuration. Note The functions vary according to different models. Refers to the actual device for details. 10.6.9 Set Image Parameters You can adjust the image parameters, video parameters, supplement parameters and capture interval. Steps 1.
DS-K1T321 Series Face Recognition Terminal Set the supplement light type, mode, start time and end time. You can also set the brightness. Capture Interval You can select the capture interval according to your actual needs. 3. Click Default to restore the parameters to the default settings. 10.6.10 Access Control Settings Set Authentication Parameters Click Configuration → Access Control → Authentication Settings . Note The functions vary according to different models.
DS-K1T321 Series Face Recognition Terminal Figure 10-8 Set Authentication Parameters Click Save to save the settings after the configuration. Terminal/Terminal Type/Terminal Model Get terminal description. They are read-only. Enable Authentication Device Enable the authentication function. Authentication Select an authentication mode according to your actual needs from the drop-down list.
DS-K1T321 Series Face Recognition Terminal You can set the interval between 2 continuous recognition of a same person during the authentication. In the configured interval, Person A can only recognized once. If another person (Person B) has recognized during the interval, Person A can recognized again. Authentication Interval You can set the authentication interval of the same person when authenticating. The same person can only authenticate once in the configured interval.
DS-K1T321 Series Face Recognition Terminal Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs.
DS-K1T321 Series Face Recognition Terminal 10.6.11 Card Settings Set Card Security Click Configuration → Card Settings → Card Type to enter the settings page. Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available.
DS-K1T321 Series Face Recognition Terminal Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting. Delete Old Events Periodically Drag the block or enter number to set the period for event deleting. All events will be deleted according to the configured time duration. Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time.
DS-K1T321 Series Face Recognition Terminal Clear Captured Pictures All captured pictures in the device will be deleted. 10.6.
DS-K1T321 Series Face Recognition Terminal Set Manual Attendance via Web Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → T&A Status to enter the settings page. 2. Set the Attendance Mode as Manual. 3. Enable the Attendance Status Required and set the attendance status lasts duration. 4.
DS-K1T321 Series Face Recognition Terminal Set Manual and Auto Attendance via Web Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → T&A Status to enter the settings page. 2.
DS-K1T321 Series Face Recognition Terminal Figure 10-10 Smart Settings Page Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K1T321 Series Face Recognition Terminal After enabling the face anti-spoofing function, you can set the matching security level when performing live face authentication. Recognition Distance Select the distance between the authenticating user and the device camera. Application Mode Select either others or indoor according to actual environment. Face Recognition Mode Normal Mode Recognize face via the camera normally. Pitch Angle The maximum pitch angle when starting face authentication.
DS-K1T321 Series Face Recognition Terminal Set the matching value when authenticating with face mask via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face with Mask 1:N Matching Threshold Set the matching threshold when authenticating with face mask via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T321 Series Face Recognition Terminal If the device has been connected to Hik-Connect and network, when there is a new installation package in Hik-Connect, you can click Upgrade after Online Update to upgrade the device system. Note Do not power off during the upgrading. Restore Parameters Click Maintenance and Security → Maintenance → Backup and Reset . Restore All All parameters will be restored to the factory settings. You should activate the device before usage.
DS-K1T321 Series Face Recognition Terminal 10.6.18 Log Query You can search and view the device logs. Go to Maintenance and Security → Maintenance → Log . Set the major and minor type of the log type. Set the start time and end time for searching, and click Search. The results will be displayed below, which including the No., time, the major type the minor type, the channel No., the local/remote user information, the remote host IP, etc. 10.6.
DS-K1T321 Series Face Recognition Terminal 6. Download the certificate and save it to an asking file in the local computer. 7. Send the asking file to a certification authority for signature. 8. Import the signed certificate. 1) Select a certificate type in the Import Passwords area, and select a certificate from the local, and click Install. 2) Select a certificate type in the Import Communication Certificate area, and select a certificate from the local, and click Install.
DS-K1T321 Series Face Recognition Terminal Chapter 11 Client Software Configuration 11.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 11-1 Flow Diagram of Configuration on Client Software 11.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T321 Series Face Recognition Terminal Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 11.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T321 Series Face Recognition Terminal you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T321 Series Face Recognition Terminal Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T321 Series Face Recognition Terminal Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T321 Series Face Recognition Terminal 11.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T321 Series Face Recognition Terminal Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 11.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 11.4.
DS-K1T321 Series Face Recognition Terminal Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T321 Series Face Recognition Terminal Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T321 Series Face Recognition Terminal ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 11.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details, fingerprint, and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T321 Series Face Recognition Terminal 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to Issue a Card by Local Mode. 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station.
DS-K1T321 Series Face Recognition Terminal Local Mode: Issue Card by Card Enrollment Station Connect a card enrollment station to the PC running the client. You can place the card on the card enrollment station to get the card number. Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E.
DS-K1T321 Series Face Recognition Terminal 11.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5.
DS-K1T321 Series Face Recognition Terminal Steps Note You can add up to 255 templates in the software system. 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2.
DS-K1T321 Series Face Recognition Terminal 4) Optional: Select a selected holiday in the right list and click click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, or 11.
DS-K1T321 Series Face Recognition Terminal Figure 11-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T321 Series Face Recognition Terminal Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 11-3 Data Synchronization 11.7 Configure Advanced Functions You can configure the advanced functions of access control to meet some special requirements in different scene.
DS-K1T321 Series Face Recognition Terminal Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T321 Series Face Recognition Terminal If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K1T321 Series Face Recognition Terminal The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Lock Door when Door Closed The door can be locked once it is closed even if the Door Locked Time is not reached.
DS-K1T321 Series Face Recognition Terminal ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired.
DS-K1T321 Series Face Recognition Terminal View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance. If the score is less than the configured value, face recognition will be failed. Face Recognition Timeout Value If the recognition time is more than the configured time, the device will remind you.
DS-K1T321 Series Face Recognition Terminal 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1.
DS-K1T321 Series Face Recognition Terminal Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K1T321 Series Face Recognition Terminal 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. Steps Note This function should be supported by the device. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3.
DS-K1T321 Series Face Recognition Terminal 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 11.8 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device. You can also control the doors such as open/close the door, or remain the door open/closed via the client remotely.
DS-K1T321 Series Face Recognition Terminal Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T321 Series Face Recognition Terminal Steps 1. Click Monitoring and select a group from the drop-down list on the upper-right corner. The access records triggered at the doors in the selected group will display in real time. You can view the details of the records, including card No., person name, organization, event time, etc. 2. Optional: Check the event type and event status so that these events will show in the list if the events are detected.
DS-K1T321 Series Face Recognition Terminal Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T321 Series Face Recognition Terminal Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T321 Series Face Recognition Terminal Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T321 Series Face Recognition Terminal Posture In order to get a good quality and accurate face picture, position your face looking at the camera when collecting or comparing face pictures. Size Make sure your face is in the middle of the collecting window.
DS-K1T321 Series Face Recognition Terminal Appendix C. Tips for Installation Environment 1.
DS-K1T321 Series Face Recognition Terminal 2.
DS-K1T321 Series Face Recognition Terminal Appendix D.
DS-K1T321 Series Face Recognition Terminal Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD30751B