DS-K1T6QT-F43 Series Face Recognition Terminal User Manual
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model Wireless DS-K1T6QT-F43MW 13.56 MHz Card Presenting Frequency, WiFi, 2.4G DS-K1T6QT-F43MFW 13.56 MHz Card Presenting Frequency, WiFi, 2.4G DS-K1T6QT-F43EW 125 KHz Card Presenting Frequency, WiFi, 2.4G DS-K1T6QT-F43EFW 125 KHz Card Presenting Frequency, WiFi, 2.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 6.6 Privacy Settings .................................................................................................................... 30 6.7 Set Administrator ................................................................................................................. 31 Chapter 7 Basic Operation ........................................................................................................ 34 7.1 Login .............................
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.5.2 Authenticate via Multiple Credential .......................................................................... 57 7.6 Basic Settings ....................................................................................................................... 57 7.7 Set Biometric Parameters .................................................................................................... 60 7.8 Set Access Control Parameters .......................
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 9.5 Search Event ...................................................................................................................... 100 9.6 Configuration ..................................................................................................................... 101 9.6.1 Set Local Parameters ................................................................................................. 101 9.6.2 View Device Information ..............
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 10.2.1 Add Device .............................................................................................................. 139 10.2.2 Reset Device Password ........................................................................................... 141 10.2.3 Manage Added Devices .......................................................................................... 142 10.3 Group Management ..................................................
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 4.3-inch LCD touch screen 2 MP wide-angle dual-lens Face anti-spoofing Face recognition distance: 0.3 m to 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 2 Appearance The appearance of the device with fingerprint is as follows: Figure 2-1 Appearance Table 2-1 Appearance Description No.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual No. 10 Name Fingerprint Module Note Only devices that support the fingerprint function contain a fingerprint module.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● ● ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 3-1 Install Gang Box 2. Use 4 supplied screws (M4) to secure the mounting plate on the gang box.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 3-2 Install Mounting Plate 3. Route the cables through the cable hole of the mounting plate, and connect to the corresponding peripherals cables. 4. Buckle into the mounting plate after aligning the device with the mounting plate. Use 1 supplied screw (M3) to secure the device on the mounting plate.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 3-3 Secure Device 3.3 Base Mounting Steps 1. Route the cables through the cable hole of the bracket, and connect the terminals with peripherals cables. Place the bracket close to the back side of the device. Figure 3-4 Place Bracket Close to Device Back Side 2. Press the bracket with both hands, and make sure that the buckle of the bracket fits with the back side of the device. Fasten the bracket in the direction of the arrow.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 3-5 Fasten Bracket 3. Buckle into the bracket to the end to complete the installation.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 4 Wiring You can connect the RS-485 terminal with the RS-485 card reader, connect the NC/NO and COM terminal with the door lock, connect the SEN and GND terminal with the door contact, the BTN/GND terminal with the exit button, and connect the Wiegand terminal with the access controller.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Group Group D No. Function Color Name Description C2 White W1 Wiegand Wiring 1 C3 Black GND Ground White/Purple NC Lock Wiring (NC) D2 White/Yellow COM Common D3 White/Red NO Lock Wiring (NO) D4 Yellow/Green SENSOR Door Contact D5 Black GND Ground D6 Yellow/Grey BUTTON Exit Door Wiring D1 Door Lock 4.2 Wire Normal Device You can connect the terminal with normal peripherals.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 4-1 Device Wiring ● ● ● Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . Do not wire the device to the electric supply directly.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 4.3 Wire Secure Door Control Unit You can connect the terminal with the secure door control unit. The wiring diagram is as follows. Figure 4-2 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 4.4 Wire Fire Module 4.4.1 Wiring Diagram of Door Open When Powering Off Lock Type: Anode Lock, Magnetic Lock, and Electric Bolt (NO) Security Type: Door Open When Powering Off Scenario: Installed in Fire Engine Access Type 1 Note The fire system controls the power supply of the access control system.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 4-3 Wire Device 14
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 4-4 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 4-5 Wiring Device 16
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 4-6 Wiring Secure Door Control Unit 4.4.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual ● ● Note The Uninterpretable Power Supply (UPS) is required. The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 4-8 Wiring Diagram 19
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note Characters containing admin and nimda are not supported to be set as activation password. 3. Click Activate. 4. Edit the device IP address. You can edit the IP address via the SADP tool, the device, and the client software. 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note After you change the system language, the device will reboot automatically. 6.2 Set Password Change Type After activating the device, you can set the password change type as reserved email address or security questions. Once you forgot the device password, you can change the password via the selected change type. Change Password via Email Address If you need to change password via reserved email, you can enter an email address, and tap Next.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note You can only select one type to change password. If you need, you can enter the web page to set both of the changing types. 6.3 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 2. Tap OK to save. ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Wired Network Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 6.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 6-5 Access to Hik-Connect 2. Tap Next. Note If you tap Previous to return to the Wi-Fi configuration page, you need to tap the connected WiFi or connect another Wi-Fi to enter the platform page again. 6.6 Privacy Settings After activation, selecting application mode, and selecting network, you should set the privacy parameters, including the picture uploading and storage.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Select parameters according to your actual needs. Figure 6-6 Privacy Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device. Save Registered Pic.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Before You Start Activate the device and select an application mode. Steps 1. Optional: Tap Skip to skip adding administrator if required. 2. Enter the administrator's name (optional) and tap Next. Figure 6-7 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual / Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected. Shortcut Keys Description Note You can configure those shortcut keys displayed on the screen. For details, see Basic Settings . ● ● Enter the device room No. and tap OK to call. Tap to call the center.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page. Figure 7-1 Admin Login 2.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Enter the password. - If you have added an administrator for the device, tap and enter the password. - If you haven't added an administrator for the device, enter the password. 3. Tap OK to enter the home page. Note The device will be locked for 30 minutes after 5 failed password attempts.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.1.3 Forgot Password If you forget the password during authentication, you can reset the password by importing the key. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the page. 2. Tap in the pop-up admin authentication page. 3. Plug USB flash drive into the USB interface. Note ● The supported USB flash drive formats are FAT32 and exfat.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-4 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually. Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 7.2.3 Set RS-485 Parameters The face recognition terminal can connect external secure door control unit or card reader via the RS-485 terminal. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-6 Set RS-485 Parameters 3. Select an peripheral type according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. 4. Tap the back icon at the upper left corner and you should reboot the device if you change the parameters.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wiegand to enter the Wiegand tab. Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Output: A face recognition terminal can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or Wiegand 34. ● Input: A face recognition terminal can connect a Wiegand card reader. to save the network parameters. 5. Tap ● Note If you change the external device, and after you save the device parameters, the device will reboot automatically. 7.2.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-8 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group. Main Channel Support N1 or None. ISUP Enable ISUP function and the data will be uploaded via EHome protocol.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Address Type Select an address type according to your actual needs. IP Address Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535. Device ID Set device serial no. Password If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only. ● ● Note Remember the ISUP account and ISUP key.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-9 Add Face Picture 6. Look at the camera. ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture .
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 8. Optional: Tap Try Again and adjust your face position to add the face picture again. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. to save the settings. 10. Tap 7.3.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual For details about the instructions of scanning fingerprints, see Tips for Scanning Fingerprint . 7. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. to save the settings. 8. Tap 7.3.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 8. Configure the card type. 9. Set the user role. Administrator The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual The user is the administrator. Except for the normal attendance function, the user can also enter the Home page to operate after authenticating the permission. Normal User The User is the normal user. The user can only authenticate or take attendance on the initial page. to save the settings. 7. Tap 7.3.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.4 Data Management You can delete data, import data, and export data. 7.4.1 Delete Data Delete user data. On the Home page, tap Data → Delete Data → User Data . All user data added in the device will be deleted. 7.4.2 Import Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Import Data . 3. Tap User Data, Face Data or Access Control Parameters .
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.4.3 Export Data Steps 1. Plug a USB flash drive in the device. 2. On the Home page, tap Data → Export Data . 3. Tap Face Data, Event Data, User Data, or Access Control Parameters. Note The exported access control parameters are configuration files of the device. 4. Optional: Create a password for exporting. When you import those data to another device, you should enter the password. ● ● ● Note The supported USB flash drive format is DB.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Enter the pin code to authenticate via PIN code. If authentication completed, a prompt "Authenticated" will pop up. 7.5.2 Authenticate via Multiple Credential Before You Start Set the user authentication type before authentication. For details, see Set Authentication Mode . Steps 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-10 Basic Settings Page Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Call Room When you tap the call button on the authentication page, you should dial a room No. to call. Call Center When you tap the call button on the authentication page, you can call the center directly. Call Specified Room No. You should set a room No. When you tap the call button on the authentication page, you can call the configured room directly without dialing. Theme You can set the theme of the prompt window on the authentication page.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance. The configurable parameters includes select application mode, face liveness level, face recognition distance, face recognition interval, face 1:N security level, face 1:1 security level, ECO settings and face with mask detection. Long tap on the initial page for 3 s and login the home page. Tap Biometric.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Table 7-1 Face Picture Parameters Parameter Description Select Application Mode Select either others or indoor according to actual environment. Face Liveness Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Face Recognition Distance Set the valid distance between the user and the camera when authenticating.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Parameter Description Set the matching value when authenticating with face mask via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face with Mask & Face (1:N ECO) Set the matching value when authenticating with face mask via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-12 Access Control Parameters The available parameters descriptions are as follows: Table 7-2 Access Control Parameters Descriptions Parameter Description Terminal Authentication Mode Select the face recognition terminal's authentication mode. You can also customize the authentication mode.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Parameter Description ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. If you adopt multiple authentication modes, you should authenticate other methods before authenticating face.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Tap T&A Status to enter the T&A Status page. Figure 7-13 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-14 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto. Figure 7-15 Auto Attendance Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note The attendance status will be valid within the configured schedule. Result When you authenticate on the initial page, the authentication will be marked as the configured attendance status according to the configured schedule. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.9.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 7-16 Manual and Auto Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual select a status to take attendance manually, the authentication will be marked as the edited attendance status. Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.10 System Maintenance You can view the device system information and capacity.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual You can view the number of administrator, user, face picture, card, and event. Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details. Upgrade Plug the USB flash drive in the device USB interface. Tap Upgrade → OK , and the device will read the digicap.dav file in the USB flash drive to start upgrading. Unlink APP Account Unlink the Hik-Connect account from the platform.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 8 Configure the Device via the Mobile Browser 8.1 Login You can login via mobile browser. ● ● Note Parts of the model supports Wi-Fi settings. Make sure the device is activated. Obtain the IP address from the device after Wi-Fi is enabled. Make sure the IP segment of the device and the computer is the same. For details, refers to Set Wi-Fi Parameters .
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-1 Add User 2) Set the following parameters. Employee ID Enter the employee ID. The Employee ID cannot be 0 or exceed 32 characters. It can be a combination of uppercase, lowercase letters and numbers. Name Enter your name. The name supports numbers, uppercase and lowercase English, and characters. The name is recommended to be within 32 characters. Gender Select the gender. User Role Select your user role. Floor No./Room No.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Start Date/End Date Set Start Date and End Date of user permission. Administrator If the user needs to be set as administrator, you can enable Administrator. Authentication Type Set the authentication type. 3) Tap Save. 3. Tap the user that needs to be edited in the user list to edit the information. 4. Tap the user that needs to be deleted in the user list, and tap to delete the user. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-2 Time Settings Tap Save to save the settings. Time Zone Select the time zone where the device is located from the drop-down list. Time Sync. Mode Manual By default, the device time should be synchronized manually. You can set the device time manually.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Set the NTP server's IP address, port No., and interval. 8.4.3 View Open Source Software License Tap Configuration → System → System Settings → About , and tap View Licenses to view the device license. 8.4.4 Network Settings You can set the port and Wi-Fi parameters. Set Port Parameters You can set the HTTP, RTSP, HTTPS, and Server according to actual needs when accessing the device via network.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-3 Wi-Fi 3. Add Wi-Fi. 1) Tap +.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-4 Add Wi-Fi 2) Enter Wi-Fi Name and Wi-Fi Password, and select Working Mode and Encryption Type. 3) Tap Save. 4. Select the Wi-Fi name, and tap Connect. 5. Enter the password and tap Save. 6. Set WLAN parameters. 1) Set the IP address, subnet mask, and gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and gateway automatically. 2) Tap Save. 8.4.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-5 Authentication Settings 2. Tap Save. Device Type Main Card Reader You can configure the device card reader's parameters. If you select main card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Minimum Card Swiping Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Recognition Interval If the interval between card presenting of the same card is less than the configured value, the card presenting is invalid.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-6 Privacy Settings Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting. Delete Old Events Periodically Enter number to set the period for event deleting. All events will be deleted according to the configured time duration. Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual The name information is desensitized with an asterisk. ID De-identification The ID information is desensitized with an asterisk. Picture Uploading and Storage You can upload and store pictures. Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically. Save Captured Picture When Authenticating If you enable this function, you can save the picture when authenticating to the device.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-7 Card Security Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticateing by presenting M1 card is available. M1 Card Encryption M1 card encryption can improve the security level of authentication.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Enable CPU Card The device can read the data from CPU card when enabling the CPU card function. CPU Card Read Content After enable the CPU card content reading function, the device can read the CPU card content. Enable ID Card Enable ID card and authenticating by presenting ID card is available. Set Card Authentication Parameters Set the card reading content when authenticate via card on the device.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual The device will read card via Wiegand 34 protocol (read 4 bytes). 8.4.6 Face Parameters Settings Set face parameters. Face Parameters Settings Tap Configuration → Smart → Intelligent Parameter . Figure 8-9 Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Set Face Parameters. Face Anti-spoofing Enable or disable the live face detection function.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Recognition Distance Select the distance between the authenticating user and the device camera. Application Mode Select Indoor or Others according to actual environment. In the outdoor scene, indoor scene near the window, or bad environment, you can choose Others. Note If the device is not activated by other tools, the device uses indoor as the environment mode by default.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Face with Mask Detection After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask1:N matching threshold, its ECO mode, and the strategy. None If the person do not wear a face mask when authenticating, the device will not prompt a notification.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100. Set Recognition Area Tap Configuration → Smart → Area Configuration to enter the page. Drag the blue frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-10 Device ID Settings (Door Station) Device Type The device can be used as a door station, outer door station, or access control device. Select a device type from the drop-down list. Note If you change the device type, you should reboot the device. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-11 Device ID Settings (Outer Door Station) Outer Door Station No. If you select outer door station as the device type, you should enter a number between 1 and 99. Note If you change the No., you should reboot the device. Configure SIP Parameters Set the device's IP address and the SIP server's IP address.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-12 Linked Network Settings Set the video intercom server IP and main station's IP. Tap Save. Press Button to Call Steps 1. Tap Configuration → Intercom → Press Button to Call to enter the settings page. 2. Set the button to call. - Check Call Indoor Station and set the indoor station No to set the button to call indoor station. - Check Call Management Center to set the button to call management center. 8.4.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-13 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual You can set the door lock status when the door lock is powering off. By default, it is Remain Closed. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended access needs swipes her/his card. Door Remain Open Duration with First Person Set the door open duration when first person is in. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 8-14 RS-485 Page Tap Save to save the settings after the configuration. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, or Access Controller. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Stop Bit The stop bit when the devices are communicating via the RS-485 protocol. Parity/Flow Ctrl/Communication Mode Enabled by default. Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Configuration → Access Control → Wiegand Settings . Figure 8-15 Wiegand Page 2. Enable Wiegand to enable the Wiegand function. 3. Set a transmission direction. Input The device can connect a Wiegand card reader.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 9 Operation via Web Browser 9.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:".
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 9.3 Live View You can view the live video of the device. After logging in, you will enter the live view page. You can perform the live view, capture, video recording, and other operations. Figure 9-1 Live View Page Function Descriptions: Select the image size when starting live view.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Full screen view. 9.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note The picture format should be JPG, JPEG or PNG. The size should be less than 200K. Click OK to save the settings. Set Permission Time Click User → Add to enter the Add Person page. Set Start Time and End Time. Click OK to save the settings. Set Access Control Click User → Add to enter the Add Person page. After check Administrator in Access Control, the added person can log in by authenticating face. You can click Add to enter the Floor No.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 9.6 Configuration 9.6.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path. Set Live View Parameters Click Configuration → Local to enter the Local page. Configure the stream type, the play performance, auto start live view, and the image format and click Save. Set Record File Saving Path Click Configuration → Local to enter the Local page.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-3 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 9.6.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-4 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 9.6.5 View Open Source Software License Go to Configuration → System → System Settings → About , and click View Licenses to view the device license. 9.6.6 Upgrade and Maintenance Reboot device, restore device parameters, and upgrade device version.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Unlink APP Account Unlink the Hik-Connect account from the platform. Import and Export Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Export Click Export to export the logs or device parameters. Note You can import the exported device parameters to another device. Import Click and select the file to import. Click Import to start import configuration file.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Security Mode High security level for user information verification when logging in the client software. Compatible Mode The user information verification is compatible with the old client software version when logging in. Enable SSH To raise network security, disable SSH service. The configuration is only used to debug the device for the professionals.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Install Other Authorized Certificate If you already has an authorized certificate (not created by the device), you can import it to the device directly. Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Import Passwords and Import Communication Certificate areas, select certificate type and upload certificate. 3. Click Install. Install CA Certificate Before You Start Prepare a CA certificate in advance. Steps 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 9.6.11 Account Security Settings You can change the security questions and answers, or the email address for the device. After change the settings, once you forgot the device password, you should answer the new questions or use the new email address to reset the device password. Steps 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need. Set Port Parameters Set the HTTP, RTSP, HTTPS and Server port parmaeters. Click Configuration → Network → Basic Settings → Port . HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add, and enter the SSID, working mode, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click Network Settings. 2) Set the IP address, subnet mask, and default gateway.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Report Strategy Settings You can set the center group for uploading the log via the ISUP protocol. Go to Configuration → Network → Basic Settings → Report Strategy . You can set the center group and the system will transfer logs via ISUP protocol. Click Save to save the settings. Center Group Select a center group from the drop-down list. Main Channel The device will communicate with the center via the main channel. Note N1 refers to wired network.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Steps Note The function should be supported by the device. 1. Click Configuration → Network → Advanced Settings → Platform . 2. Select ISUP from the platform access mode drop-down list. 3. Check Enable. 4. Set the ISUP version, and view the alarm receiver type, server address, port, device ID, register status. Note If you select 5.0 as the version, you should set the ISUP key as well. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-7 Video Settings Page Set the stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, the video encoding, and I Frame Interval. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio . Set the audio stream type and audio encoding. You can also drag the block to adjust the device input and output volume.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-8 Customize Audio Content 2. Select Prompt as TTS(Text to Speech) to turn the text to audio content. 3. Select time schedule. 4. Enable the function. 5. Set the appellation. 6. Set the time period when authentication succeeded. 1) Click Add. 2) Set the time duration and the language.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. Set the time duration when authentication failed. 7. 1) Click Add. 2) Set the time duration and the language.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-9 Image Settings Page 2. Configure the parameters to adjust the image. Video Standard Set the video frame rate when performing live view remotely. After changing the standard, you should reboot the device to take effect. PAL 25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East countries, Europe countries, etc.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 30 frames per second. Suitable for the USA, Canada, Japan, Taiwan (China), Korea, the Philippines, etc. WDR Enable or disable the WDR function. When there are both very bright and very dark areas simultaneously in the view, WDR balances the brightness level of the whole image and provide clear images with details.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual person to the shift group and assign a shift schedule (a rule for the attendance defining how the schedule repeats, the shift type, break settings, and the card swiping rule.) to the shift group to define the attendance parameters for the persons in the shift group. Disable Attendance Mode via Web Disable the attendance mode and the system will not display the attendance status on the initial page. Steps 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. Result You should select an attendance status manually after authentication. Note If you do not select a status, the authentication will be failed and it will not be marked as a valid attendance. Set Auto Attendance via Web Set the attendance mode as auto, and you can set the attendance status and its available schedule.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. 6. Set the status' schedule. Refers to Time Settings for details. Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-11 Set Authentication Parameters Click Save to save the settings after the configuration. Device Type Select Main Card Reader or Sub Card Reader from the drop-down list. Main Card Reader You can configure the device card reader's parameters. Sub Card Reader You can configure the connected peripheral card reader's parameters.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Get card reader type and description. They are read-only. Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Recognition Interval You can set the interval between 2 continuous recognition of a same person during the authentication. In the configured interval, Person A can only recognized once.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Enable to report alarm when the card reading attempts reach the set value. Max. Authentication Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Communication with Controller Every When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Max.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Name De-identification You can check Name De-identification, and the whole name will not be displayed. Picture Uploading and Storage Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically. Save Captured Picture When Authenticating If you enable this function, you can save the picture when authenticating to the device.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption M1 card encryption can improve the security level of authentication. Sector Enable the function and set the encryption sector. By default, Sector 13 is encrypted.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 9.6.20 Video Intercom Settings Set Video Intercom Parameters The device can be used as a door station, outer door station, or access control device. You should set the device No. before usage. Click Configuration → Video Intercom → Device No. Figure 9-12 Set Video Intercom Parameters If set the device type as Door Station and Access Control Device, you can set the floor No., door station No., and click Advanced Settings to set the community No.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. If set the device type as Outer Door Station, you can set the outer door station No., and click Advanced Settings to set the community No. Outer Door Station No.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Press Button to Call Steps 1. Click Intercom → Press Button to Call to enter the settings page. 2. Set the parameters. - Edit call No. for every button. - Check Call Management Center to set the button calling center. Note If you check Call Management Center and set the call No. as well, call management center has higher privilege than call No. 9.6.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Open.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-14 Wiegand Page 2. Check Wiegand to enable the Wiegand function. 3. Set a transmission direction. Input The device can connect a Wiegand card reader. Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 9.6.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-15 Set Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. Live Face Detection Security Level After enabling the face anti-spoofing function, you can set the matching security level when performing live face authentication. Recognition Distance Select the distance between the authenticating user and the device camera.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Face Recognition Timeout Value Set the timeout value when face recognizing. If the face recognition time is longer than the configured value, the system will pop up a prompt. Face with Mask Detection After enabling the face with mask detection, the system will recognize the captured face with mask picture. You can set face with mask1:N matching threshold, its ECO mode, and the strategy.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Set the matching value when authenticating with face mask via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face with Mask 1:N Matching Threshold (ECO Mode) Set the matching threshold when authenticating with face mask via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 9-16 Theme Page Display Mode You can select display theme for device authentication. You can select Display Mode as Simple or Normal. When you select Simple, the information of name, ID, face picture will be not displayed. Sleep Enable Sleep and the device will enter the sleep mode when no operation within the configured sleep time.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Slide Show Interval Drag the block or enter the number to set the slide show interval. The picture will be changed according to the interval.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Chapter 10 Client Software Configuration 10.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 10-1 Flow Diagram of Configuration on Client Software 10.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 10.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 10.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 10.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 10.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 10.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details, fingerprint, and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to Issue a Card by Local Mode. 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Local Mode: Issue Card by Card Enrollment Station Connect a card enrollment station to the PC running the client. You can place the card on the card enrollment station to get the card number. Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 10.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Steps Note You can add up to 255 templates in the software system. 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 4) Optional: Select a selected holiday in the right list and click click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, or 10.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Figure 10-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 10-3 Data Synchronization 10.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual If enable the function, the device can recognize the EM card. You can present EM card on the device. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s).
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. Lock Door when Door Closed The door can be locked once it is closed even if the Door Locked Time is not reached.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance. If the score is less than the configured value, face recognition will be failed. Face Recognition Timeout Value If the recognition time is more than the configured time, the device will remind you.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface. Face Picture Database select Deep Learning as the face picture database. Authenticate by QR Code If enabled, the device camera can scan the QR code to authenticate. By default, the function is disabled.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically. Set Wiegand Parameters You can set the access control device's Wiegand channel and the communication mode. After setting the Wiegand parameters, the device can connect to Wiegand card reader via Wiegand communication.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings. 10.8 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Steps 1. Click Monitoring and select a group from the drop-down list on the upper-right corner. The access records triggered at the doors in the selected group will display in real time. You can view the details of the records, including card No., person name, organization, event time, etc. 2. Optional: Check the event type and event status so that these events will show in the list if the events are detected.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Posture In order to get a good quality and accurate face picture, position your face looking at the camera when collecting or comparing face pictures. Size Make sure your face is in the middle of the collecting window.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual 2.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T6QT-F43 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD30753B
