DS-K3B801SX Series Swing Barrier User Manual
DS-K3B801SX Series Swing Barrier User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K3B801SX Series Swing Barrier User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles.
DS-K3B801SX Series Swing Barrier User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K3B801SX Series Swing Barrier User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K3B801SX Series Swing Barrier User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K3B801SX Series Swing Barrier User Manual • Do not ingest battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
DS-K3B801SX Series Swing Barrier User Manual • Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. • Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only.
DS-K3B801SX Series Swing Barrier User Manual Available Models Product Name Swing Barrier Model Description DS-K3B801SX-L Left Pedestal DS-K3B801SX-M Middle Pedestal DS-K3B801SX-R Right Pedestal viii
DS-K3B801SX Series Swing Barrier User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Introduction ........................................................................................................................... 1 1.2 Main Features ........................................................................................................................ 1 Chapter 2 System Wiring ...........
DS-K3B801SX Series Swing Barrier User Manual 5.6.8 Barrier Control Wiring ................................................................................................. 39 5.6.9 Alarm Output Wiring ................................................................................................... 41 Chapter 6 Device Settings ......................................................................................................... 42 6.1 Set Study Mode ......................................................
DS-K3B801SX Series Swing Barrier User Manual 8.4.5 Take a Photo via Client ................................................................................................ 66 8.4.6 Collect Face via Access Control Device ....................................................................... 67 8.4.7 Collect Fingerprint via Client ....................................................................................... 68 8.4.8 Collect Fingerprint via Access Control Device .....................................
DS-K3B801SX Series Swing Barrier User Manual 8.7.6 Configure First Person In ............................................................................................. 95 8.7.7 Configure Anti-Passback ............................................................................................. 96 8.7.8 Configure Device Parameters ...................................................................................... 97 8.8 Configure Linkage Actions for Access Control ......................................
DS-K3B801SX Series Swing Barrier User Manual Appendix A. Tips for Scanning Fingerprint ............................................................................... 117 Appendix B. DIP Switch ........................................................................................................... 119 B.1 DIP Switch Description ....................................................................................................... 119 B.2 DIP Switch Corresponded Functions .................................
DS-K3B801SX Series Swing Barrier User Manual Chapter 1 Overview 1.1 Introduction The swing barrier with two barriers and 24 IR lights is designed to detect unauthorized entrance or exit. By adopting the swing barrier integrated with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc. 1.
DS-K3B801SX Series Swing Barrier User Manual • Anti-forced-accessing The barrier will be locked automatically without open-barrier signal.
DS-K3B801SX Series Swing Barrier User Manual Chapter 2 System Wiring The preparation before installation and wiring. Steps 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals. Note The distance between the nearest two line is L+100 mm. L represents the lane width. 3. Slotting on the installation surface and dig installation holes according to the hole position diagram.
DS-K3B801SX Series Swing Barrier User Manual 4. Bury cables. Each lane buries 1 network cable and 1 high voltage cable. For details, see the system wiring diagram below. Figure 2-2 System Wiring Diagram (General Wiring) • • • • • • Note The supplied interconnecting cable length is 5.5 m. The suggested inner diameter of the low voltage conduit is larger than 30 mm.
DS-K3B801SX Series Swing Barrier User Manual Figure 2-3 Wire Face Recognition Terminal • • • • • • • • Note The supplied interconnecting cable length is 5.5 m. The left pedestal and the middle pedestal should bury interconnecting cables for connecting the face recognition terminal. The face recognition terminal installed on the left pedestal will gain power from the 12 V power supply, which should connect to the electric supply.
DS-K3B801SX Series Swing Barrier User Manual Chapter 3 Installation 3.1 Disassemble before Installation Before installation, you should disassemble the pedestal and remove some screws. Before You Start • Keep the disassembled components and screws. • You should prepare the following tools to disassemble the pedestal: 1. Pedestal Key (supplied); 2. Allen Wrench (2.5 mm); 3. Allen Wrench (3 mm); 4. Allen Wrench (4 mm). Steps 1. Use the pedestal key to open the front and back components.
DS-K3B801SX Series Swing Barrier User Manual Figure 3-2 M5×25 Screws 3. Remove the components along the arrow direction carefully. Figure 3-3 Remove Components 4. Loosen the wing bolt (M4 × 10) at the front and back of the pedestal, and remove the front and back base covers along the arrow direction.
DS-K3B801SX Series Swing Barrier User Manual Figure 3-4 Loosen Wing Bolt Figure 3-5 Remove Base Cover You can start installing the expansion screws to secure the device on the installation surface. 5. Remove the motor bottom cover. 1) Pull or push the barrier to the closed position. 2) Use the Allen wretch (2.5 mm) to loosen the 4 screws (M4 × 8) on the motor bottom cover.
DS-K3B801SX Series Swing Barrier User Manual Figure 3-6 M4×8 Screw 3) Pull or push the barrier to the open position, and remove the motor bottom cover.
DS-K3B801SX Series Swing Barrier User Manual Figure 3-7 Remove Motor Bottom Cover Note If dissembling the middle pedestal, you should dissemble two motor bottom covers. 6. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 × 12) at the front or back of the pedestal base and remove the side base cover slowly.
DS-K3B801SX Series Swing Barrier User Manual Note If dissembling the middle pedestal, you should dissemble two side base covers. 7. Disassemble the two protective sheets at the bottom for wiring, and you can start wiring the interconnecting cable. Figure 3-9 Disassemble Two Protective Sheets 3.2 Install Pedestals Before You Start Prepare for the installation tools, check the device and the accessories, and clear the installation base.
DS-K3B801SX Series Swing Barrier User Manual 2. Drill holes on the ground according to the installation holes on the pedestals and insert the expansion sleeves. 3. According to the entrance and exit marks on the pedestals, move the pedestals to the corresponded positions. Note Make sure the installation holes on the pedestals and the base are aligned with each other. 4. Secure the pedestals with expansion bolts. Note • Do not immerse the pedestal in the water.
DS-K3B801SX Series Swing Barrier User Manual 5. After installation, assemble the components and screws back to the pedestal in reverse order (except for protective sheets).
DS-K3B801SX Series Swing Barrier User Manual Chapter 4 Disassemble before Maintenance Before maintaining the inner components, you should disassemble the pedestal and remove some screws. Note • Keep the disassembled components and screws organized. • You should prepare the following tools to disassemble the pedestal: 1. Pedestal Key (supplied); 2. Allen Wrench (2.5 mm); 3. Allen Wrench (3 mm); 4. Allen Wrench (4 mm). 4.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-1 Lock Position 2.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-2 M5×25 Screws Position 3. Remove the components along the arrow direction carefully.
DS-K3B801SX Series Swing Barrier User Manual 4.2 Disassemble Motor Bottom Cover After disassembling the motor bottom cover, you can maintain the lane control board and the barrier position control board. Steps 1. Pull or push the barrier to the closed position. 2. Use the Allen wretch (2.5 mm) to loosen the 4 screws (M4 × 8) on the motor bottom cover. Figure 4-4 M4×8 Screws Position 3. Pull or push the barrier to the open position, and remove the motor bottom cover.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-5 Remove Bottom Cover Note If dissembling the middle pedestal, you should dissemble two motor bottom covers. 4.3 Disassemble Side Base Cover After disassembling the side base cover, you can maintain the IR sending/receiving board. Steps 1. Use the pedestal key to open the front and back components.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-6 Lock Position 2. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 × 25) at the top of the device.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-7 M5×25 Screws Position 3. Remove the components along the arrow direction carefully. Figure 4-8 Remove Components 4. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 × 12) at the front or back of the pedestal base and remove the side base cover slowly.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-9 Remove Side Base Cover Note If dissembling the middle pedestal, you should dissemble two side base covers. 4.4 Disassemble Top Cover After disassembling the top cover, you can maintain the components at the top of the pedestal, the IR sending/receiving board and the IR adaptor for instance. Steps 1. Use the Allen wretch (2.5 mm) to loosen the 4 captive panel screws at the top of the pedestal. Figure 4-10 Loosen Captive Panel Screw 2.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-11 Remove Front and Back Top Cover 3. Optional: If you should install the fingerprint modules in the pedestal, you should use the key to open and remove the front and back components, and cut off the fingerprint modules' power. 4. Use the Allen wrench (2.5 mm) to loosen the 2 captive panel screws displayed in the picture below. Figure 4-12 Top Captive Panel Screws 5. Remove the top cover along the arrow's direction.
DS-K3B801SX Series Swing Barrier User Manual Figure 4-13 Remove Top Cover 23
DS-K3B801SX Series Swing Barrier User Manual Chapter 5 General Wiring 5.1 Components Introduction By default, basic components of the turnstile are connected well. The pedestals can communicate by wiring the interconnecting cables. And the turnstile supports wiring the AC electric supply for the whole system’s power supply. Note The voltage fluctuation of the electric supply is between 100 VAC and 220 VAC, 50 to 60 Hz. The picture displayed below describes each component's position on the turnstile.
DS-K3B801SX Series Swing Barrier User Manual Figure 5-1 Components Diagram The picture displayed below describes the IR sending/receiving module and their corresponding number on the pedestal.
DS-K3B801SX Series Swing Barrier User Manual Figure 5-2 IR Sending/Receiving Module Position Note If the turnstile contains two lanes, standing at the entrance position, the IR modules on the left pedestal are the IR sending modules. The IR modules on the right pedestal are the IR receiving modules. The IR modules on the left side of the middle pedestal are the IR receiving modules, while the IR modules on the right side of the middle pedestal are the IR sending modules. 5.
DS-K3B801SX Series Swing Barrier User Manual Note • The cable bare part should be no more than 8 mm. It is suggested that you can immerse the bare part into the liquid tin. If possible, wear an insulation cap at the end of the bare cable. Make sure there’s no bare copper or cable after the wiring. • The Terminal L and the Terminal N cannot be wired reversely. Do not wire the input and output terminal reversely.
DS-K3B801SX Series Swing Barrier User Manual Figure 5-3 Cable Hole of Interconnecting Cable Follow the instructions below to connect the interconnecting cable. Figure 5-4 Connect Interconnecting Cable 5.4 Wire Network Switch Connect the network cable and the network switch. Steps 1. Open the side cover of the pedestal.
DS-K3B801SX Series Swing Barrier User Manual Note For details, see Disassemble Side Base Cover . Figure 5-5 Network Switch Position 2. Lead out 12 V power supply from the main switch and connect it to the network switch's power interface. 3. Connect the network cable with the network switch. 5.5 Face Recognition Terminal Power Supply Wiring You should wire the power supply terminal on the 12 V power supply component if you connect the turnstile to the face recognition terminal.
DS-K3B801SX Series Swing Barrier User Manual Figure 5-6 Face Recognition Terminal Power Supply Wiring Position 5.6 Terminal Description The lane controller contains main lane controller and sub lane controller, which controls the IR beams, motor, and other components' work. 5.6.
DS-K3B801SX Series Swing Barrier User Manual Figure 5-7 Main Control Board 5.6.2 Sub Control Board Terminal Description The sub lane control board contains power supply interface, supercapacitor interface, brake interface, motor drive interface, light board interface, motor encoder interface, door open position detection interface, debug port, lane communication interface, and interconnecting interface. The picture displayed below is the sub control board diagram.
DS-K3B801SX Series Swing Barrier User Manual 5.6.
DS-K3B801SX Series Swing Barrier User Manual Access Control Board Terminal Description RS-485 Interface Power Output 2 RS-232 Interface Power Input Event Input Exit Button Door Lock (Relay) GND Grounding GND Grounding RS-485 B- Connect to Card Reader RS485- RS-485 B+ Connect to Card Reader RS485+ GND Grounding RS-485 C- Connect to Card Reader RS485- RS-485 C+ Connect to Card Reader RS485+ 5V 5 VDC Power Output GND 5 VDC Grounding GND Grounding RS-232 G- Connect to Card Reader RS232
DS-K3B801SX Series Swing Barrier User Manual Access Control Board Terminal Description D2+ Alarm Output NO/NC1 Alarm Output Relay 1 (Dry Contact) COM1 NO/NC2 Alarm Output Relay 2 (Dry Contact) COM2 NO/NC3 Alarm Output Relay 3 (Dry Contact) COM3 NO/NC4 Alarm Output Relay 4 (Dry Contact) COM4 Network Interface • • • • • • • LAN Network Accessing Note The alarm input hardware interface is normally open by default. So only the normally open signal is allowed.
DS-K3B801SX Series Swing Barrier User Manual 5.6.4 Access Control Board Serial Port ID Description You can use the jumper cap on the access control board to switch the interface communication mode. For details about switching between RS-232 and RS-485 communication type, see Switching RS-485/RS-232 Mode. Figure 5-10 Access Control Board According to the picture above, the RS-485 serial port corresponds to UART2 and UART3. RS-232 serial port is corresponded to UART7 and UART8.
DS-K3B801SX Series Swing Barrier User Manual Use the jumper cap to switch the serial port communication mode with the lane controller. By default, the interface is wired and it is in RS-485 communication mode. If wiring other controllers (compatible with Hikvision communication protocol), use the jumper cap to switch between RS-485 and RS-232 communication mode.
DS-K3B801SX Series Swing Barrier User Manual 5.6.5 RS-485 Wiring Note • There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR code scanner, fingerprint and card reader, card recycler, text screen, fingerprint reader, and face recognition terminal. Take the wiring of RS-485 card reader as an example. • For details about text screen, see Configuring Screen Parameters in User Manual of iVMS-4200 AC Client Software. 5.6.
DS-K3B801SX Series Swing Barrier User Manual 38
DS-K3B801SX Series Swing Barrier User Manual 5.6.7 Wiegand Wiring Note Connect the OK/ERR/BZ if the access controller should control the LED and buzzer of the Wiegand card reader. 5.6.8 Barrier Control Wiring By default, the barrier has connected with the access control board. The lane control board can control the barrier status. If possible, the device can connect with a third party lane control board to control the third party barriers.
DS-K3B801SX Series Swing Barrier User Manual Entering Wiring Exiting Wiring 40
DS-K3B801SX Series Swing Barrier User Manual 5.6.9 Alarm Output Wiring Note For details about changing the relay output status via the jumper cap, see Alarm Relay Output Mode (NO/NC) .
DS-K3B801SX Series Swing Barrier User Manual Chapter 6 Device Settings After installation and wiring completed, you should set the barriers closed position (study mode) before entering the working mode. You can also set the test mode, normal mode, passing mode and memory mode, pair the keyfob, initialize the hardware, switching between RS-485 communication mode and RS-232 communication mode, and view relay output NO/NC diagram by setting the DIP switch on the access control board.
DS-K3B801SX Series Swing Barrier User Manual 5. Set the No.1 switches of the 8-digit DIP Switch on the main control board by referring to the following figure. 6. Power on the device again. Note For details about the DIP switch value and meaning, see DIP Switch Description. The barrier will open automatically and turns back to the closed position. At this circumstance, the device enters the normal mode. 6.
DS-K3B801SX Series Swing Barrier User Manual Note • Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the keyfob will select only one of them to pair. • For details about DIP switch value and meaning, see DIP Switch . 6. Optional: Go to System → User → Keyfob User on the remote control page of the client software to delete the keyfob. 6.3 Initialize Device Steps 1. Remove the JP11 jumper cap on the access control board. Figure 6-1 Initialization Jumper Cap 2.
DS-K3B801SX Series Swing Barrier User Manual 6.4 Switch to RS-485/RS-232 Mode Take the Serial Port 4 and on the access control board as an example. If the Jumper cap's position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-485 communication mode. Figure 6-2 Jumper Cap Status of RS-485 Interface If the Jumper cap's position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-232 communication mode.
DS-K3B801SX Series Swing Barrier User Manual 6.5 Switch Relay Output Mode (NO/NC) 6.5.
DS-K3B801SX Series Swing Barrier User Manual Alarm Relay Output Mode (NC): 47
DS-K3B801SX Series Swing Barrier User Manual Chapter 7 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: • The default IP address: 192.0.0.64 • The default port No.: 8000 • The default user name: admin 7.
DS-K3B801SX Series Swing Barrier User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 7.
DS-K3B801SX Series Swing Barrier User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 7.
DS-K3B801SX Series Swing Barrier User Manual Chapter 8 Client Software Configuration 8.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 8-1 Flow Diagram of Configuration on Client Software 8.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K3B801SX Series Swing Barrier User Manual 8.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click Refresh Every 60s to refresh the information of the online devices.
DS-K3B801SX Series Swing Barrier User Manual Figure 8-3 Add Single Online Device Figure 8-4 Add Multiple Online Devices 4. Enter the required information. Name Enter a descriptive name for the device. IP Address Enter the device's IP address. The IP address of the device is obtained automatically in this adding mode. Port You can customize the port number. The port number of the device is obtained automatically in this adding mode.
DS-K3B801SX Series Swing Barrier User Manual By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B801SX Series Swing Barrier User Manual 2. Click Device tab on the top of the right panel. 3. Click Online Device to show the online device area at the bottom of the page. The searched online devices are displayed in the list. 4. Select multiple devices. Note For the inactive device, you need to create the password for it before you can add the device properly. For details, refer to . 5. Click Add to open the device adding window. 6. Enter the required information.
DS-K3B801SX Series Swing Barrier User Manual 2. Click Device tab on the top of the right panel. The added devices are displayed on the right panel. 3. Click Add to open the Add window, and then select IP/Domain as the adding mode. 4. Enter the required information. Name Create a descriptive name for the device. For example, you can use a nickname that can show the location or feature of the device. Address The IP address or domain name of the device. Port The devices to add share the same port number.
DS-K3B801SX Series Swing Barrier User Manual Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 8. Finish adding the device. - Click Add to add the device and back to the device list page. - Click Add and New to save the settings and continue to add other device. Add Devices by IP Segment If the devices share the same port No.
DS-K3B801SX Series Swing Barrier User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 6. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS (Transport Layer Security) protocol for security purpose . Note • This function should be supported by the device.
DS-K3B801SX Series Swing Barrier User Manual User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B801SX Series Swing Barrier User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B801SX Series Swing Barrier User Manual Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3. Select a group from the group list and select the resource type as Access Point, Alarm Input, Alarm Output, etc. 4. Click Import. 5. Select the thumbnails/names of the resources in the thumbnail/list view.
DS-K3B801SX Series Swing Barrier User Manual 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 8.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 8.4.
DS-K3B801SX Series Swing Barrier User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person. 3. Click Add to open the adding person window. The Person ID will be generated automatically. 4. Enter the basic information including person name, gender, telephone number, email address, validity period, etc.
DS-K3B801SX Series Swing Barrier User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Credential → Card area, click +. 4. Click Settings to enter the Settings page. 5. Select Local as the card issuing mode. Figure 8-6 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station.
DS-K3B801SX Series Swing Barrier User Manual Buzzing Enable or disable the buzzing when the card number is read successfully. Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8.
DS-K3B801SX Series Swing Barrier User Manual - Click Add and New to add the person and continue to add other persons . 8.4.5 Take a Photo via Client When adding a person, you can take a photo of the her/him via the client and set this photo as the person's profile. Before You Start Make sure PC running the client has a camera or you have connected other USB camera to the PC. Steps 1. Enter Person module. 2.
DS-K3B801SX Series Swing Barrier User Manual Figure 8-7 Take a Photo via Client 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 8.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2.
DS-K3B801SX Series Swing Barrier User Manual 4. Select Remote Collection. 5. Select an added access control device or the enrollment station from the drop-down list. Note If you select the enrollment station, you should click Login to set related parameters of the device including IP address, port No., user name, and password. Also, you can check Face AntiSpoofing and select the liveness level as Low, Medium, or High.
DS-K3B801SX Series Swing Barrier User Manual 6. Collect the fingerprint. 1) Click Start. 2) Place and lift your fingerprint on the fingerprint recorder to collect the fingerprint. 3) Click Add to save the recorded fingerprint. 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. Note Once the fingerprint is added, the fingerprint type cannot be changed. 8.4.
DS-K3B801SX Series Swing Barrier User Manual 8.4.9 Configure Access Control Information When adding a person, you can set her/his access control information, such as binding an access control group with the person, configuring PIN code, setting the person as a visitor, a blocklist person, or a super user, etc. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. 3. In the Access Control area, click to select access group(s) for the person.
DS-K3B801SX Series Swing Barrier User Manual For details about setting the door's open duration, refer to Configure Parameters for Door . Add to Blocklist Add the person to the blocklist and when the person tries to access doors/floors, an event will be triggered and sent to the client to notify the security personnel. Mark as Visitor If the person is a visitor, you should set the her/his valid times for visit. Note The valid times for visit is between 1 and 100.
DS-K3B801SX Series Swing Barrier User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 2) In the Custom Information panel, enter the person information. 3) Click Add to add the person and close the Add Person window, or click Add and New to add the person and continue to add other persons. 8.4.
DS-K3B801SX Series Swing Barrier User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Additional Information panel, enter the additional information of the person, including person's ID type, ID No., job title, etc., according to actual needs. 4. Confirm to add the person. - Click Add to add the person and close the Add Person window.
DS-K3B801SX Series Swing Barrier User Manual 8.4.15 Import Person Pictures After importing face pictures for the added persons to the client, the persons in the pictures can be identified by an added face recognition terminal. You can either import person pictures one by one, or import multiple pictures at a time according to your need. Before You Start Be sure to have imported person information to the client beforehand. Steps 1. Enter the Person module. 2.
DS-K3B801SX Series Swing Barrier User Manual 8.4.17 Export Person Pictures You can export face picture file of the added persons and save in your PC. Before You Start Make sure you have added persons and their face pictures to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4.
DS-K3B801SX Series Swing Barrier User Manual Note If you select the enrollment station, you should click Login, and set IP address, port No., user name and password of the device. 5. Click Import to start importing the person information to the client. Note Up to 2,000 persons and 5,000 cards can be imported. The person information, including person details, person's fingerprint information (if configured), and the linked cards (if configured), will be imported to the selected organization. 8.4.
DS-K3B801SX Series Swing Barrier User Manual 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station. - Swipe the card on the card reader. - Manually enter the card number and press the Enter key. The person(s) in the list will be issued with card(s). 8.4.21 Report Card Loss If the person lost his/her card, you can report the card loss so that the card's related access authorization will be inactive. Steps 1. Enter Person module. 2.
DS-K3B801SX Series Swing Barrier User Manual Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or IC card according to the actual card type. Serial Port It is only available when the model is DS-K1F100-M. Select the COM the card enrollment station connects to.
DS-K3B801SX Series Swing Barrier User Manual Steps Note You can add up to 64 holidays in the software system. 1. 2. 3. 4. 5. Click Access Control → Schedule → Holiday to enter the Holiday page. Click Add on the left panel. Create a name for the holiday. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. Add a holiday period to the holiday list and configure the holiday duration. Note Up to 16 holiday periods can be added to one holiday.
DS-K3B801SX Series Swing Barrier User Manual 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2. 3. 4. 5. Click Add on the left panel to create a new template.
DS-K3B801SX Series Swing Barrier User Manual 8.6 Set Access Group to Assign Access Authorization to Persons After adding the person and configuring the person's credentials, you can create the access groups to define which person(s) can get access to which door(s) and then apply the access group to the access control device to take effect. Before You Start • Add person to the client. • Add access control device to the client and group access points. For details, refer to Group Management . • Add template.
DS-K3B801SX Series Swing Barrier User Manual Figure 8-9 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K3B801SX Series Swing Barrier User Manual You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 8-11 Data Synchronization 8.7 Configure Advanced Functions You can configure the advanced functions of access control to meet some special requirements in different scene. Note • For the card related functions(the type of access control card), only the card(s) with access group applied will be listed when adding cards.
DS-K3B801SX Series Swing Barrier User Manual 2. Select an access device to show its parameters on the right page. 3. Turn the switch to ON to enable the corresponding functions. Note The displayed parameters may vary for different access control devices. RS-485 Communication Redundancy You should enable this function if you wire the RS-485 card reader to the access control device redundantly. Enable NFC If enable the function, the device can recognize the NFC card. You can present NFC card on the device.
DS-K3B801SX Series Swing Barrier User Manual Note s The displayed parameters may vary for different access control devices. Name Edit the card reader name as desired. Exit Button Type You can set the exit button as remaining closed or remaining open. Usually, it is remaining open. Open Duration After swiping the normal card and relay action, the time for locking the door starts working. Door Left Open Timeout Alarm The alarm can be triggered if the door has not been closed in a configured time period.
DS-K3B801SX Series Swing Barrier User Manual Configure Parameters for Card Reader After adding the access control device, you can configure its card reader parameters. Steps 1. Click Access Control → Advanced Function → Device Parameter . 2. In the device list on the left, click to expand the door, select a card reader and you can edit the card reader's parameters on the right. 3. Edit the card reader basic parameters in the Basic Information page.
DS-K3B801SX Series Swing Barrier User Manual Communicate with Controller Every When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Fingerprint Recognition Level Select the fingerprint recognition level in the drop-down list. 5. Click OK. 6. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s).
DS-K3B801SX Series Swing Barrier User Manual Passing Mode Select the controller which will control the barrier status of the device. • If you select According to DIP Settings, the device will follow the controller's DIP settings to control the barrier. The settings on the software will be invalid. • If you select According to Door's Schedule Settings, the device will follow the schedule configured in the client software to control the barrier. The DIP settings of the controller will be invalid.
DS-K3B801SX Series Swing Barrier User Manual Do Not Open Barrier When Lane is Not Clear If there is someone or something in the lane, the gate will not open even if the credential is authenticated. This function is designed to avoid more than one person passing through the gate with only one authentication. 4. Click OK. 8.7.2 Configure Remaining Open/Closed You can set the status of the door as open or closed.
DS-K3B801SX Series Swing Barrier User Manual 4. To set the door status during the holiday, click the Holiday and perform the following operations. 1) Click Remain Open or Remain Closed. 2) Click Add. 3) Enter the start date and end date. 4) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Note Up to 8 time durations can be set to one holiday period. 5) Perform the following operations to edit the time durations.
DS-K3B801SX Series Swing Barrier User Manual Note Make sure you have issue card to the person. Make sure you have set access group and apply the access group to the access control device successfully. 5) Click Save. 6) Optional: Select the person/card group(s), and then click Delete to delete it(them). 7) Optional: Select the person/card group(s), and then click Apply to re-apply access group that failed to be applied previously to the access control device. 4.
DS-K3B801SX Series Swing Barrier User Manual 4) Select the added person/card group in the left list below and it will be added to the Selected list on the right as the authentication group. 5) Click the added authentication group in the right list to set authentication times in the Auth Times column. Note • The authentication times should be larger than 0 and smaller than the added personnel quantity in the personnel group. • The maximum value of authentication times is 16. 6) Click Save.
DS-K3B801SX Series Swing Barrier User Manual 4. Click Select Device to select the access control device for setting the custom wiegand. 5. Set the parity mode according to the property of the third party card reader. Note • Up to 80 bits are allowed in the total length. • The odd parity start bit, the odd parity length, the even parity start bit and the even parity length range from 1 to 80 bit. • The start bit of the card ID, the manufacturer code, the site code, and the OEM should range from 1 to 80 bit.
DS-K3B801SX Series Swing Barrier User Manual Steps 1. Click Access Control → Advanced Function → Authentication to enter the authentication mode configuration page. 2. Select a card reader on the left to configure. 3. Set card reader authentication mode. 1) Click Configuration. Figure 8-14 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information .
DS-K3B801SX Series Swing Barrier User Manual Figure 8-15 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 8.7.6 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K3B801SX Series Swing Barrier User Manual Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication. Authorization by First Person All authentications (except for the authentications of super card, super password, duress card, and duress code) are allowed only after the first person authorization.
DS-K3B801SX Series Swing Barrier User Manual 4. Click of the selected first card reader in the Card Reader Afterward column to open the select card reader dialog. 5. Select the afterward card readers for the first card reader. Note Up to four afterward card readers can be added as afterward card readers for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect.
DS-K3B801SX Series Swing Barrier User Manual • The configured parameters will be applied to the device automatically. • When you change the working mode or connection mode, the device will reboot automatically. Enable M1 Card Encryption M1 card encryption can improve the security level of authentication. Steps Note The function should be supported by the access control device and the card reader. 1. Enter the Access Control module. 2.
DS-K3B801SX Series Swing Barrier User Manual Before You Start Add access control device to the client. Steps 1. Click Event Configuration → Access Control Event . The added access control devices will display in the device list. 2. Select a resource (including device, alarm input, door, and card reader) from the device list. The event types which the selected resource supports appear. 3.
DS-K3B801SX Series Swing Barrier User Manual 2. 3. 4. 5. 6. Select the access control device from the list on the left. Click Add button to add a new linkage. Select the event source as Event Linkage. select the event type and detailed event to set the linkage. In the Linkage Target area, set the property target to enable this action. Buzzer on Controller The audible warning of access control device will be triggered. 7. Click Save. 8.
DS-K3B801SX Series Swing Barrier User Manual Note The device should support recording. Alarm Output The alarm output will be triggered for notification. Alarm Input Arm or disarm the alarm input. Note The device should support alarm input function. Access Point The door status of open, close, remain open, or remain closed will be triggered. Audio Play The audio prompt will be triggered. And the select audio index related audio content will be played according to the configured play mode. 8. Click Save.
DS-K3B801SX Series Swing Barrier User Manual 8.9.1 Control Door Status You can control the status for the door(s), including unlock door, locking door, remaining the door unlock, remaining the door locked, remain all unlocked, etc. Before You Start • Add person and assign access authorization to designed person, and person will have the access authorization to the access points (doors). For details, refer to Person Management and Set Access Group to Assign Access Authorization to Persons .
DS-K3B801SX Series Swing Barrier User Manual Remain All Locked All doors in the group will be closed and locked. No person can access the doors even if he/she has the authorized credentials, except the super users. Capture Capture a picture manually. Note The Capture button is available when the device supports capture function. The picture is saved in the PC running the client. For setting the saving path, refer to Set File Saving Path in the user manual of the client software.
DS-K3B801SX Series Swing Barrier User Manual Note You can right click the column name of access event table to show or hide the column according to actual needs. 2. Optional: Select an access point group from the drop-down list in the upper-right corner to show the real time access records of the selected group. 3. Optional: Check the event type and event status. The detected events of checked type and status will be displayed in the list below. 4.
DS-K3B801SX Series Swing Barrier User Manual 8.10.1 Enable Receiving Event from Devices Before the client software can receive event notifications from the device, you need to arm the device first. Steps 1. Click → Tool → Device Arming Control to open Device Arming Control page. All the added devices appear on this page. 2. Optional: If there are to many devices, enter the key words in Filter filed to filter the device(s) you want.
DS-K3B801SX Series Swing Barrier User Manual Before You Start Enable receiving events from devices before the client can receive event from the device, see Enable Receiving Event from Devices for details. Steps 1. Click Event Center → Real-time Event to enter the real-time event page and you can view the real-time events received by the client. Event Time For encoding device, event time is the client time when it receives the event. For other device types, event time is the time when the event is triggered.
DS-K3B801SX Series Swing Barrier User Manual Note You should configure the email parameters first, see Set Email Parameters in the user manual of the client software for details. Auto-Play Video Check Auto-Play Video to automatically play video when displaying event details. Enlarge Video or Picture • Double click the video image to view video in a larger window. • Put the cursor on the picture, and click to view picture in a larger window.
DS-K3B801SX Series Swing Barrier User Manual Note • For video intercom device, you need to select search scope: All and Locking Log. • For access control device, you can click Show More to set more conditions: status, event type, card reader type, person name, card No., and organization. Priority The priority including low, medium, high and uncategorized which indicates the emergency degree of the event. Event Type Select one or more event types to be searched from the drop-down list.
DS-K3B801SX Series Swing Barrier User Manual Figure 8-19 Search Historical Event 4. Optional: Right click the table header of the event list to customize the event related items to be displayed in the event list. 5. Select an event in the event list to view the event details. 6. Optional: Perform one of the following operations. Handle Single Event Handle single event: Select one event that needs to be handled, and then click Handle in the event information details page, and enter the handling suggestion.
DS-K3B801SX Series Swing Barrier User Manual Send Email Select an event and then click Send Email, and the information details of this event will be sent by email. Note You should configure the email parameters first, see Set Email Parameters in the user manual of the client software for details. Export Event Information Click Export to export the event log or event pictures to the local PC in CSV/Excel file. You can set the saving path manually.
DS-K3B801SX Series Swing Barrier User Manual 4. Optional: Check Enable NTP and set the NTP server address, the NTP port, and the synchronization interval. 5. Optional: Check Enable DST and set the DST start time, end time and the bias. 6. Click Save. 8.11.4 Set System Maintenance You can reboot the device remotely, restore the device to default settings, etc. Steps 1. Click Maintenance and Management → Device Management → Device to enter the device list. 2. Click to enter the remote configuration page. 3.
DS-K3B801SX Series Swing Barrier User Manual 5. Optional: Select a user in the user list and click Edit to edit the user. You are able to edit the user password, the IP address, the MAC address and the user permission. 6. Click OK. 8.11.6 Manage Keyfob User Steps 1. Click Maintenance and Management → Device Management → Device to enter the device list. 2. Click to enter the remote configuration page. 3. Click System → User → Keyfob User . 4. Click Add to add the user. 5.
DS-K3B801SX Series Swing Barrier User Manual 8.11.8 Configure Lane Parameters You can set the passing parameters for a person to pass through the turnstile. Steps 1. Click Maintenance and Management → Device to enter the device list. 2. Click to enter the remote configuration page. 3. Click System → Lane Settings . 4. Set the lane parameters. Door Closing Delay Time Set the delayed time duration when barrier is closing. The barrier will be closed after the configured delayed time. Max.
DS-K3B801SX Series Swing Barrier User Manual Select the screen's position on the device. If select Exit from the drop-down list, the screen will be installed at the exit position of the device. Screen Model Select the screen model from the drop-down list. Font Size Select the text font size in the screen. Screen Orientation Select the text orientation on the screen. Line Space Set the space between two lines. Column Spacing Set the space between two columns.
DS-K3B801SX Series Swing Barrier User Manual Invalid The device will not count people. If the device people counting function is enabled, the people counting function is still disabled. By Detection The device will count the people who passing through the device depending on the detection result. By Authentication Number The device will count the people who authenticating on the device. The failed authentication will also count as once. 5. Click Save. 8.11.
DS-K3B801SX Series Swing Barrier User Manual Note • The imported audio file should be in MEM format. • For details about converting other format of the audio file to MEM format, see the audio conversion manual. • If you use the third part software to create or edit an audio file, the volume of the audio file should be no less than 0 × 68. If the volume is less than the value, it will exceed the loudspeaker's power consumption, so that damage the loudspeaker. 8.11.
DS-K3B801SX Series Swing Barrier User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K3B801SX Series Swing Barrier User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
DS-K3B801SX Series Swing Barrier User Manual Appendix B. DIP Switch B.1 DIP Switch Description The DIP switch is on the main lane control board. No.1 to No 8 is from the low bit to the high bit. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12. B.
DS-K3B801SX Series Swing Barrier User Manual Bit 4 5 to 8 Device Mode Keyfob Paring Mode Passing Mode Function Decimal Value Disable Memory Mode 1 Disable Keyfob Paring Mode 0 Enable Keyfob Paring Mode 1 Controlled Bidirection 0 Controlled Entrance and Prohibit Exit 1 Controlled 2 Entrance and Free Exit Free Bi-direction 3 Free Entrance and 4 Controlled Exit Free Entrance and 5 Prohibit Exit Prohibited Bidirection 120 6 DIP Switch Address Diagram
DS-K3B801SX Series Swing Barrier User Manual Bit Device Mode Function Prohibit Entrance 7 and Controlled Exit Prohibit Entrance 8 and Free Exit 121 Decimal Value DIP Switch Address Diagram
DS-K3B801SX Series Swing Barrier User Manual Appendix C.
DS-K3B801SX Series Swing Barrier User Manual Appendix D. Table of Audio Index Related Content Index Content 1 Authenticated. 2 Card No. does not exist. 3 Card No. and fingerprint mismatch. 4 Climbing over the barrier. 5 Reverse passing. 6 Passing timeout. 7 Intrusion. 8 Force accessing. 9 Tailgating. 10 No permissions. 11 Authentication time out. 12 Authentication failed. 13 Expired card. 14 Staying out of time.
DS-K3B801SX Series Swing Barrier User Manual Appendix E. Error Code Description The swing barrier will display the error code on the seven-segment display if error occurred. Refer to the table below to find the description of each number.
DS-K3B801SX Series Swing Barrier User Manual Error Reason Code Error Reason Code The Third IR Beam on Lower IR 15 Board Triggered Lower IR Board 8 Offline 44 The Fourth IR Beam on Lower IR Board Triggered 16 Lower IR Board 9 Offline 45 The Fifth IR Beam on Lower IR Board Triggered 17 Lower IR Board 10 Offline 46 The Sixth IR Beam on Lower IR Board Triggered 18 Lower IR Board 11 Offline 47 The Seventh IR Beam on Lower 19 IR Board Triggered Lower IR Board 12 Offline 48 The Eighth IR Beam
DS-K3B801SX Series Swing Barrier User Manual Appendix F. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure F-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD22973B
