DS-K3B961TX Series Swing Barrier User Manual
DS-K3B961TX Series Swing Barrier User Manual Legal Information ©2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K3B961TX Series Swing Barrier User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K3B961TX Series Swing Barrier User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
DS-K3B961TX Series Swing Barrier User Manual This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.
DS-K3B961TX Series Swing Barrier User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K3B961TX Series Swing Barrier User Manual ● ● Do not ingest battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
DS-K3B961TX Series Swing Barrier User Manual ● ● ● ● ● ● ● Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only.
DS-K3B961TX Series Swing Barrier User Manual Available Models Product Name Swing Barrier Model Description DS-K3B961TX-L/M Left Pedestal DS-K3B961TX-M/M Middle Pedestal DS-K3B961TX-R/M Right Pedestal viii
DS-K3B961TX Series Swing Barrier User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Introduction ........................................................................................................................... 1 1.2 Main Features ........................................................................................................................ 1 1.3 Light Description .............
DS-K3B961TX Series Swing Barrier User Manual 5.3 Initialize Device .................................................................................................................... 30 Chapter 6 Activation ................................................................................................................. 33 6.1 Activate via Device ............................................................................................................... 33 6.2 Activate via Web Browser ...................
DS-K3B961TX Series Swing Barrier User Manual 7.8.14 Set Video and Audio Parameters .............................................................................. 52 7.8.15 Customize Audio Content ......................................................................................... 54 7.8.16 Set Image Parameters ............................................................................................... 56 7.8.17 Event Linkage ...........................................................................
DS-K3B961TX Series Swing Barrier User Manual 8.5.2 Add Template .............................................................................................................. 89 8.6 Set Access Group to Assign Access Authorization to Persons .............................................. 90 8.7 Configure Advanced Functions ............................................................................................ 92 8.7.1 Configure Device Parameters ..........................................................
DS-K3B961TX Series Swing Barrier User Manual Chapter 1 Overview 1.1 Introduction The flap barrier with two barriers and 24 IR lights is designed to detect unauthorized entrance or exit. By adopting the flap barrier integratedly with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc. 1.
DS-K3B961TX Series Swing Barrier User Manual ● ● ● ● Custom broadcasting content LED indicates the entrance/exit and passing status White indicators for card and QR code authentication; Red and green arrow indicators; Adjustable brightness and color of entrance light and side light IR emergency mode and Custom Anti-pinch for Door Closing 1.3 Light Description Side Light The side light indicates different status of the lane, including inductive, prohibited and authenticated passing.
DS-K3B961TX Series Swing Barrier User Manual Arrow Light ● ● ● ● The arrow light stays off when the device is on standby mode and the light will be on when authentication is completed. Green light for authenticated passing and red light for failed authentication. The arrow light will be off after pass-through. The light will stay red in the sign of X when passing is prohibited or alarm sounds.
DS-K3B961TX Series Swing Barrier User Manual Chapter 2 System Wiring The preparation before installation and general wiring. Steps ● ● Note The device should be installed on the concrete surface or other non-flammable surfaces. If the installation area is too close to the wall, make sure the distance between the pedestal and the wall should be no less than 20 mm, or you cannot open the pedestal's top panel.
DS-K3B961TX Series Swing Barrier User Manual ● The dimension is as follows.
DS-K3B961TX Series Swing Barrier User Manual Figure 2-1 Dimension 1. Draw a central line on the installation surface of the left or right pedestal. Note If the installation area is near the wall, make sure the central line is at least 78.5 mm away from the wall, or you cannot open the pedestal's top panel. 2. Draw other parallel lines for installing the other pedestals. Note The distance between the nearest two line is L + 242 mm. L represents the lane width. 3.
DS-K3B961TX Series Swing Barrier User Manual Figure 2-2 Hole Position Diagram 4. Bury cables. Each lane buries 1 network cable, 1 high voltage cable and 1 low voltage cable. For details, see the system wiring diagram below.
DS-K3B961TX Series Swing Barrier User Manual Figure 2-3 System Wiring Diagram (General Wiring) ● ● ● ● ● ● Note The supplied interconnecting cable length is 5.5 m. The suggested inner diameter of the low voltage conduit is larger than 30 mm. If you want to bury both of the AC power cord and the low voltage cable, the two cables should be in separated conduits to avoid interference.
DS-K3B961TX Series Swing Barrier User Manual Chapter 3 Installation 1. Before installation, you should disassemble the pedestal with the key. 2. Keep the disassembled components and make sure the accessories are intact. 3. Prepare for system wiring and installation. For details, see System Wiring . 4. Fix the pedestal to the installation spot with screws. Scan the QR Code to view the installation guide video.
DS-K3B961TX Series Swing Barrier User Manual Chapter 4 General Wiring ● ● Note When you should maintain or disassemble the high voltage modules, you should remove the entire high voltage modules and maintain it outside the turnstile. You should unplug the cables that connected to the peripherals before maintenance to avoid destroy of the device. When disassembling the high voltage module, you should disconnect the power to avoid injury. 4.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-1 Components Diagram Note For details about wiring arrangement, refers to the actual device. The picture displayed below describes the IR adapter and the IR sending/receiving module and their corresponding number on the pedestal.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-2 IR Modules ● ● ● Note For details about wiring arrangement, refers to the actual device. If the turnstile contains two lanes, standing at the entrance position, the IR modules on the left pedestal are the IR sending modules. The IR modules on the right pedestal are the IR receiving modules.
DS-K3B961TX Series Swing Barrier User Manual 4.3 Terminal Description The lane controller contains main lane controller and sub lane controller, which controls the IR beams, motor, and other components' work. 4.3.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-3 Main Lane Control Board Terminal 4.3.2 Sub Lane Control Board Terminal Description The sub lane control board contains debugging port, access control board communication interface, power interface, supercapacitor, IR adapter and ArrowBoard interface, encoder interface, power supply for motor, brake interface, sub user extended interface board BUS and interconnecting interface. The picture displayed below is the sub control board diagram.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-4 Sub Lane Control Board Terminal 4.3.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-5 Main Access Control Board Terminal 4.3.4 Sub Access Control Board Terminal Description The sub access control board contains screen adapter interface, sensor interface, loudspeaker interface, IR light interface, user extended interface board and lane control board communication interface, sub access control board interface, power interface, card reader board interface, TF card slot, initialization button, debugging port and USB flash drive interface.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-6 Sub Access Control Board Terminal 17
DS-K3B961TX Series Swing Barrier User Manual 4.3.
DS-K3B961TX Series Swing Barrier User Manual Main User Extended Interface Description RS-232 Interface RS-485 Wiegand Card Reader Alarm Output GND Grounding 232RX Connect to Card Reader RS232RX 232TX Connect to Card Reader RS232TX 485- Connect to Card Reader RS485- 485+ Connect to Card Reader RS485+ 12 V 12 VDC Power Input BZ Card Reader Buzzer Control Output W0 Wiegand Head Read Data Input Data0 W1 Wiegand Head Read Data Input Data1 GND Grounding NO/NC1 Alarm Output Relay 1 (Dry C
DS-K3B961TX Series Swing Barrier User Manual Main User Extended Interface Description Power Output 3 Exit Button Fire Input 5VOUT1 5 VDC Power Output 1 5VOUT1 5 VDC Power Output 2 GND Grounding BTN Door Signal Input GND Grounding ALARM IN Fire Alarm Input GND Grounding 20
DS-K3B961TX Series Swing Barrier User Manual 4.3.
DS-K3B961TX Series Swing Barrier User Manual Main User Extended Interface Description RS-232 Interface RS-485 Wiegand Card Reader Power Output 1 Power Output 2 Power Output 3 Exit Button 232RX Connect to Card Reader RS232RX 232TX Connect to Card Reader RS232TX 485- Connect to Card Reader RS485- 485+ Connect to Card Reader RS485+ 12 V 12 VDC Power Input BZ Card Reader Buzzer Control Output W0 Wiegand Head Read Data Input Data0 W1 Wiegand Head Read Data Input Data1 GND Grounding 24VO
DS-K3B961TX Series Swing Barrier User Manual 4.3.7 User Core Board Terminal Description The user core board terminal contains network interface, BUS, USB card reader interface, access control board communication interface, card receiver and RS-485 card reader interface, power interface, programming interface and debugging port. The picture displayed below is the user core board diagram. Figure 4-9 User Core Board Terminal 4.3.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-10 RS-485 Wiring 4.3.9 RS-232 Wiring Note The main and sub user extended interface board each has two RS-232 interface. Figure 4-11 RS-232 Wiring 4.3.
DS-K3B961TX Series Swing Barrier User Manual Note Connect the OK/ERR/BZ if the access controller should control the LED and buzzer of the Wiegand card reader. 4.3.11 Barrier Control Wiring According to the barrier control interfaces and the internal relays, the device provides 2 groups of the barrier control signals on the main user extended interface board, including 1 remaining open interface and 1 remaining closed interface.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-14 Alarm Output Wiring 1 Figure 4-15 Alarm Output Wiring 2 4.3.13 Alarm Input Wiring On the main user extended interface board, you can wire the fire alarm input interface.
DS-K3B961TX Series Swing Barrier User Manual Figure 4-17 Remaining Closed 27
DS-K3B961TX Series Swing Barrier User Manual Chapter 5 Device Settings After installation and wiring completed, the turnstile will study the open and closed position automatically. After the learning, the turnstile is in the normal mode. You can also set the turnstile to study mode, normal mode, and pair the keyfob, initialize the hardware via the main user extended interface board (middle/right pedestal). Study Mode Study the closed position. Normal Mode The device will work properly.
DS-K3B961TX Series Swing Barrier User Manual 6. Set the No.1 switches of the 4-digit DIP Switch on the main user extended interface board by referring to the following figure. Figure 5-2 Normal Mode 7. Power on the device again. Note For details about the DIP switch value and meaning, see DIP Switch Description. The barrier will open automatically and turns back to the closed position. At this circumstance, the device enters the normal mode. 5.
DS-K3B961TX Series Swing Barrier User Manual Figure 5-3 Enable Keyfob Paring Mode 3. Power on the turnstile and it will enter the keyfob pairing mode. 4. Hold the Close button for more than 10 seconds. The keyfob's indicator of the will flash twice if the pairing is completed. 5. Set the No.2 switch to the OFF side, and reboot the turnstile to take effect. Note ● Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the keyfob will select only one of them to pair.
DS-K3B961TX Series Swing Barrier User Manual Figure 5-4 Initialization Button Position 2. Power off and reboot the device. The device buzzer buzzes a long beep. 3. When the beep stopped, release the initialization button. Caution The initialization of the device will restore all the parameters to the default setting and all the device events are deleted.
DS-K3B961TX Series Swing Barrier User Manual Note Make sure no persons are in the lane when powering on the device. The initialization is completed.
DS-K3B961TX Series Swing Barrier User Manual Chapter 6 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 6.
DS-K3B961TX Series Swing Barrier User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B961TX Series Swing Barrier User Manual 6.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. ● The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address.
DS-K3B961TX Series Swing Barrier User Manual 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 6.4 Activate Device via iVMS-4200 Client Software For some devices, you are required to create the password to activate them before they can be added to the iVMS-4200 software and work properly.
DS-K3B961TX Series Swing Barrier User Manual Chapter 7 Operation via Web Browser 7.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login.
DS-K3B961TX Series Swing Barrier User Manual You can view the status of the access control board, lane control board, extended interface board, side light board, IR adaptors and camera. Peripheral You can view the status of the RS-485 card reader, USB card reader and tamper input. Temperature You can view the pedestal temperature and the status of the motor encoder.
DS-K3B961TX Series Swing Barrier User Manual You can view the status of the access control board, lane control board, side light board, IR adaptors and camera. Peripheral You can view the status of the RS-485 card reader, RS-232 card reader, USB card reader and tamper input. Temperature You can view the pedestal temperature and the status of the motor encoder. Passing Mode You can view the entrance and exit mode. IR Detector Status You can view the status of each pair of the 24 IR beam sensors.
DS-K3B961TX Series Swing Barrier User Manual Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view. You can select from the main stream and the sub stream. Full screen view. 7.
DS-K3B961TX Series Swing Barrier User Manual If you enable Always Valid,the permission time setting is not required. Click OK to save the settings. Set Access Control Click User → Add to enter the Add Person page. After check Administrator in Access Control, the added person can log in the device by authentication. Click OK to save the settings. Add Authentication Mode Click User → Add to enter the Add Person page. Set the authentication type. Click OK to save the settings.
DS-K3B961TX Series Swing Barrier User Manual 7.6 Search Event Click Search to enter the Search page. Figure 7-4 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel.
DS-K3B961TX Series Swing Barrier User Manual 7.7 Device Management You can manage the linked device on the page. Steps 1. Click Device Management to enter the settings page. Figure 7-5 Device Management 2. Click Add to add the indoor station or sub door station. Enter the parameters and click OK to add. 3. Click Import. Enter the information of the device in the template to import devices in batch. 4. Click Export to export the information to the PC. 5.
DS-K3B961TX Series Swing Barrier User Manual Set Live View Parameters Click Configuration → Local to enter the Local page. Configure the stream type, the play performance, auto start live view, and the image format and click Save. Set Record File Size and Saving Path Click Configuration → Local to enter the Local page. Select a record file size and select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details.
DS-K3B961TX Series Swing Barrier User Manual Figure 7-6 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list. Time Sync. NTP You should set the alarm receiver type, NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 7.8.
DS-K3B961TX Series Swing Barrier User Manual 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 7.8.5 View Open Source Software License Go to Configuration → System → System Settings → About , and click View Licenses to view the device license. 7.8.6 Upgrade and Maintenance Reboot device, restore device parameters, and upgrade device version. Reboot Device Click Configuration → System → Maintenance → Upgrade & Maintenance .
DS-K3B961TX Series Swing Barrier User Manual All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information. Unlink APP Account Unlink the Hik-Connect account from the platform. Import and Export Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Export Click Export to export the logs or device parameters.
DS-K3B961TX Series Swing Barrier User Manual On the Device for Management page, click Configuration → System → Security → Security Service . Enable SSH To raise network security, disable SSH service. The configuration is only used to debug the device for the professionals. Enable HTTP In order to increase the network security level when visiting websites, you can enable HTTP to acquire a more secure and encrypted network communication environment.
DS-K3B961TX Series Swing Barrier User Manual Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Import Passwords and Import Communication Certificate areas, select certificate type and upload certificate. 3. Click Install. Install CA Certificate Before You Start Prepare a CA certificate in advance. Steps 1. Go to Configuration → System → Security → Certificate Management . 2. Create an ID in the Inport CA Certificate area.
DS-K3B961TX Series Swing Barrier User Manual 7.8.11 Online Users The information of users logging into the device is shown. Go to Configuration → System → User Management → Online Users to view the list of online users. 7.8.12 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → User Management → Arming/Disarming Information . You can view the device arming/disarming information. Click Refresh to refresh the page. 7.8.
DS-K3B961TX Series Swing Barrier User Manual Figure 7-9 TCP/IP Settings Page Set the parameters and click Save to save the settings. DHCP If you disable the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, and DNS server. If you enable the function, the system will allocate the IPv4 address, IPv4 subnet mask, the IPv4 default gateway and DNS server automatically.
DS-K3B961TX Series Swing Barrier User Manual Select network card from the drop-down list. NIC Type Select a NIC type from the drop-down list. By default, it is Auto. DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need. Set Port Parameters Set the HTTP, RTSP and HTTPS port parmaeters. Click Configuration → Network → Basic Settings → Port . HTTP It refers to the port through which the browser accesses the device.
DS-K3B961TX Series Swing Barrier User Manual Set Video Parameters Click Configuration → Video/Audio → Video . Figure 7-10 Video Settings Page Set the video channel, camera name, stream type, the video type, the resolution, the bitrate type, the video quality, the frame rate, the Max. bitrate, the video encoding, and I Frame Interval.
DS-K3B961TX Series Swing Barrier User Manual Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio . Select the audio channel. You can also drag the block to adjust the device output volume. Click to enable Voice Prompt. Click Save to save the settings after the configuration. Note The functions vary according to different models. Refers to the actual device for details. 7.8.
DS-K3B961TX Series Swing Barrier User Manual 5. Set the time period when authentication succeeded. 1) Click Add. 2) Set the time duration. Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Set the audio content. TTS If you choose TTS, you need to set the language and enter the prompt content of authentication success.
DS-K3B961TX Series Swing Barrier User Manual 8. Click Save to save the settings. 7.8.16 Set Image Parameters Set the display settings, video standard, WDR, image adjustment, supplement light, and beauty. Steps 1. Click Configuration → Image . 2. Configure the parameters to adjust the image. Display Settings Set the entrance or exit display. Video Standard Set the video frame rate when performing live view remotely. After changing the standard, you should reboot the device to take effect.
DS-K3B961TX Series Swing Barrier User Manual 7.8.17 Event Linkage Set linked actions for events. Steps 1. Click Configuration → Event → Basic Event → Event Linkage to enter the page. Figure 7-12 Event Linkage 2. Set event source. - If you choose Linkage Type as Event Linkage, you need to select event types from the dropdown list. - If you choose Linkage Type as Card Linkage, you need to enter the card No. and select the card reader.
DS-K3B961TX Series Swing Barrier User Manual Enable Linked Audio Prompt and select the play mode. ● If you choose TTS, you need to set language and enter the prompt content. ● If you choose Audio File, you need to select an available audio file from the drop-down list or click Audio File Management to add a new audio file. Capture Linkage Enable Capture Linkage and select the card reader to capture for the target event. 7.8.
DS-K3B961TX Series Swing Barrier User Manual Note The authentication interval value ranges from 0 to 255. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Max. Authentication Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Communication with Controller Every When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically.
DS-K3B961TX Series Swing Barrier User Manual Name De-identification You can check Name De-identification, and the whole name will not be displayed. ID De-identification You can check ID De-identification, and the ID will not be displayed. Picture Uploading and Storage Upload Picture After Linked Capture Upload the pictures captured by linked camera to the platform automatically. Save Pictures After Linked Capture If you enable this function, you can save the picture captured by linked camera to the device.
DS-K3B961TX Series Swing Barrier User Manual Note The device will upload the person's authentication information to the platform. The plat form will judge to open the barrier or not. 2) Optional: Enable Verify Credential Locally. Note After enabling the function, the device will only verify the person's permission without the schedule template, etc. 3) Select ID card verification center from the drop-down list. 4) Optional: Enable Blocklist Authentication. 3.
DS-K3B961TX Series Swing Barrier User Manual Enable FeliCa Card The device can read the data from FeliCa card when enabling the FeliCa card function. Set Card Authentication Parameters Set the card reading content when authenticate via card on the device. Go to Configuration → General → Card Authentication Settings . Select a card authentication mode and enable reversed card No. at your actual needs. Click Save. 7.8.
DS-K3B961TX Series Swing Barrier User Manual Figure 7-13 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Open.
DS-K3B961TX Series Swing Barrier User Manual Super Password The specific person can open the door by inputting the super password. Note The duress code and the super code should be different. Serial Port Settings Set serial port parameters. Steps 1. Click Configuration → Access Control → Serial Port Settings .
DS-K3B961TX Series Swing Barrier User Manual Figure 7-14 Serial Port Settings 2. Set Serial Port Position as Main Channel or Sub Lane Control Board. 3. Click to enable serial port settings. 4. Set the No., Baud Rate, Data Bit, Stop Bit, Parity and Communication Mode. 5. Set the Peripheral Type as Card Receiver, QR Code Scanner or Disable. 6. You can view the serial port type, connected device model and peripheral software version. 7. Click Save.
DS-K3B961TX Series Swing Barrier User Manual 7.8.20 Turnstile Basic Parameters Set turnstile basic parameters. Steps 1. Click Configuration → Turnstile → Basic Parameters to enter the page. Figure 7-15 Basic Parameters 2. View the Device Type, Device Model and Working Status. 3. Set Barrier Material, Lane Width, Opening Barrier Speed and Closing Barrier Speed. 4. Set the passing mode. - If you choose General Passing, you can select the barrier status for the entrance and exit from the drop-down list.
DS-K3B961TX Series Swing Barrier User Manual Steps 1. Click Configuration → Turnstile → Basic Parameters to enter the page. Figure 7-16 keyfob 2. View the keyfob working status. 3. Set Working Mode as One-to-One or One-to-Many. 4. Add keyfob. 1) Click Add and the keyfob adding window will pop up. 2) Enter the Name and Serial No.. 3) Check to enable Remain Open Permission at your actual needs. 4) Click OK to add the keyfob. 5. Optional: Select a keyfob and click Delete to delete the keyfob. 6. Click Save.
DS-K3B961TX Series Swing Barrier User Manual If some IR beams do not work properly, you can shield those IR beams to restore the lane. But this action may hit person and cause injury. Enable Custom Anti-pinch for Door Closing Anti-pinch for door closing refers that the barrier will not close if the device has detected person in the lane. Only after the person walks out of the lane, the barrier will close. If you enable the function, you can shield parts of the IR beams for closing barrier in advance.
DS-K3B961TX Series Swing Barrier User Manual Figure 7-19 Light Settings 2. Set side light. 1) Set Light Brightness as Auto or Manual. If you choose Manual, you can drag the block or enter the value to adjust the light brightness manually. 2) Set inductive, prohibited and auth. passing light color. 3. Set barrier light. 1) Check to enable Light on When on Standby at your actual needs. 2) Set the barrier light. 4. Set entrance light. 1) Check to enable Light on When on Standby at your actual needs.
DS-K3B961TX Series Swing Barrier User Manual 3) Set the color of standby light, auth. completed light, auth. failed light and alarm light. 5. Click Save. Other Settings Set other parameters. Steps 1. Click Configuration → Turnstile → Other Settings to enter the page. 2. Set Alarm Output Duration. Note The alarm output duration ranges from 0 s to 3599 s. 3. Set Temperature Unit. 4. Check to enable Do Not Open Barrier When Lane is Not Clear. 5.
DS-K3B961TX Series Swing Barrier User Manual Note The functions vary according to different models. Refers to the actual device for details. Figure 7-20 Smart Settings Page Click Save to save the settings after the configuration. Face Recognition Mode Normal Mode Recognize face via the camera normally.
DS-K3B961TX Series Swing Barrier User Manual Deep Mode The device can recognize a much wider people range than the normal mode. This mode is applicable to a more complicated environment. Enable Face Recognition If enabling the function, the device will start face recognition. Card Reader Choose the entrance or exit card reader from the drop-down list. Face Anti-spoofing Enable or disable the live face detection function.
DS-K3B961TX Series Swing Barrier User Manual Face without Mask Detection After enabling the face without mask detection, the system will recognize the captured face with mask picture or not. You can set face with mask1:N matching threshold, it's ECO mode, and the strategy. None The function is disabled. The device will not detect whether a person is wearing a face mask or not.
DS-K3B961TX Series Swing Barrier User Manual Click Save to save the settings. Click or to record videos or capture pictures. 7.8.22 Set Theme You can set the display mode and the sleep time for the device. Click Configuration → Theme → Theme . Click Entrance or Exit to set theme, Click Save. Display Mode You can select display theme for device authentication. You can select Display Mode as Simple, Authentication Mode, or Advertisement.
DS-K3B961TX Series Swing Barrier User Manual If you choose picture, you can click + in Picture area and select a picture from the material database to display on the device screen saver. ● If you choose welcome message, you can select the Template, and enter the main title and the sub title, and select the Font Size and Font Color. You can also click Custom to select the customized background picture from the material database.
DS-K3B961TX Series Swing Barrier User Manual Chapter 8 Client Software Configuration You can call the hotline to get the iVMS-4200 client software installation package. 8.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software.
DS-K3B961TX Series Swing Barrier User Manual 8.2 Device Management The client supports managing access control devices and video intercom devices. Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 8.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol.
DS-K3B961TX Series Swing Barrier User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B961TX Series Swing Barrier User Manual 5. Open the exported template file and enter the required information of the devices to be added on the corresponding column. Note For detailed description of the required fields, refer to the introductions in the template. Adding Mode Enter 0 or 1 or 2. Address Edit the address of the device. Port Enter the device port number. The default port number is 80. User Name Enter the device user name. By default, the user name is admin.
DS-K3B961TX Series Swing Barrier User Manual All the online devices sharing the same subnet will be displayed in the list. 3. Select the device from the list and click on the Operation column. 4. Reset the device password. - Click Generate to pop up the QR Code window and click Download to save the QR code to your PC. You can also take a photo of the QR code to save it to your phone. Send the picture to our technical support.
DS-K3B961TX Series Swing Barrier User Manual View Online User Click to view the details of online user who access the device, including user name, user type, IP address and login time. Refresh Device Information Click to refresh and get the latest device information. 8.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations.
DS-K3B961TX Series Swing Barrier User Manual 2. Click Device Management → Group to enter the group management page. 3. Select a group from the group list and select the resource type as Access Point, Alarm Input, Alarm Output, etc. 4. Click Import. 5. Select the thumbnails/names of the resources in the thumbnail/list view. Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 8.
DS-K3B961TX Series Swing Barrier User Manual 8.4.2 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2.
DS-K3B961TX Series Swing Barrier User Manual 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. to select a face picture file. 5. Click Note ● The (folder of) face pictures should be in ZIP format.
DS-K3B961TX Series Swing Barrier User Manual Before You Start ● Make sure you have added persons and their face pictures to an organization. ● Make sure you have enabled the Export Person Information function to display the Export button. See for details. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export on the top menu bar. 4.
DS-K3B961TX Series Swing Barrier User Manual Note If you select the enrollment station, you should click Login, and enter IP address, port No., user name and password of the device. 5. Select the Getting Mode. Note The getting mode varies according to different devices. The access control device supports getting the person information by employee ID. Up to 5 employee IDs can be specified each time. 6. Click Import to start importing the person information to the client.
DS-K3B961TX Series Swing Barrier User Manual Steps 1. Enter Person module. 2. Select the person you want to report card loss for and click Edit to open the Edit Person window. on the added card to set this card as lost card. 3. In the Credential → Card panel, click After reporting card loss, the access authorization of this card will be invalid and inactive. Other person who gets this card cannot access the doors by swiping this lost card. to cancel the loss. 4.
DS-K3B961TX Series Swing Barrier User Manual Enable or disable the buzzing when the card number is read successfully. Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-D8E. If the card is M1 card, and if you need to enable the M1 Card Encryption function, you should enable this function and select the sector of the card to encrypt.
DS-K3B961TX Series Swing Barrier User Manual 2) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Note Up to 8 time durations can be set to one holiday period. 3) Optional: Perform the following operations to edit the time durations. ● Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to .
DS-K3B961TX Series Swing Barrier User Manual 1) Click Week Schedule tab on the lower panel. 2) Select a day of the week and draw time duration(s) on the timeline bar. Note Up to 8 time duration(s) can be set for each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. ● Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to .
DS-K3B961TX Series Swing Barrier User Manual picture, linkage between card number and fingerprint, linkage between card number and fingerprint, card password, card effective period, etc). 1. Click Access Control → Authorization → Access Group to enter the Access Group interface. 2. Click Add to open the Add window. 3. In the Name text field, create a name for the access group as you want. 4. Select a template for the access group. Note You should configure the template before access group settings.
DS-K3B961TX Series Swing Barrier User Manual 3) Click Apply All to Devices or Apply Changes to Devices. Apply All to Devices This operation will clear all the existed access groups of the selected devices and then apply the new access group to the device. Apply Changes to Devices This operation will not clear the existed access groups of the selected devices and only apply the changed part of the selected access group(s) to the device(s).
DS-K3B961TX Series Swing Barrier User Manual ● ● ● Note For the card related functions(the type of access control card/multi-factor authentication), only the card(s) with access group applied will be listed when adding cards. The advanced functions should be supported by the device. Hover the cursor on the Advanced Function, and then Click to customize the advanced function(s) to be displayed. 8.7.
DS-K3B961TX Series Swing Barrier User Manual Display the card information when authenticating. Display Person Information Display the person information when authenticating. Overlay Person Info. on Picture Display the person information on the captured picture. Voice Prompt If you enable this function, the voice prompt is enabled in the device. You can hear the voice prompt when operating in the device. Upload Pic.
DS-K3B961TX Series Swing Barrier User Manual 3. Select a door or floor to show its parameters on the right page. 4. Edit the door or floor parameters. ● ● Note The displayed parameters may vary for different access control devices. Some of the following parameters are not listed in the Basic Information page, click More to edit the parameters. Name Edit the card reader name as desired. Door Contact You can set the door sensor as remaining closed or remaining open. Usually, it is remaining closed.
DS-K3B961TX Series Swing Barrier User Manual Note ● The duress code, super code, and dismiss code should be different. ● The duress code, super password, and the dismiss code should be different from the authentication password. ● The length of duress code, super password, and the dismiss code is according the device, usually it should contains 4 to 8 digits. 5. Click OK. 6. Optional: Click Copy to , and then select the door/floor(s) to copy the parameters in the page to the selected doors/floor(s).
DS-K3B961TX Series Swing Barrier User Manual When you inputting the password on the card reader, if the interval between pressing two digits is larger than the set value, the digits you pressed before will be cleared automatically. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Max. Times of Card Failure Set the max. failure attempts of reading card. Tampering Detection Enable the anti-tamper detection for the card reader.
DS-K3B961TX Series Swing Barrier User Manual Set the matching security level when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate when authentication. Live Face Detection Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K3B961TX Series Swing Barrier User Manual Alarm Output Active Time How long the alarm output will last after triggered. 4. Click OK. 5. Optional: Set the switch on the upper right corner to ON to trigger the alarm output. Configure Parameters for Lane Controller After adding the lane controller to the client, you can configure its parameters for passing through the lane. Before You Start Add access control device to the client. Steps 1.
DS-K3B961TX Series Swing Barrier User Manual Temperature Unit Select the temperature unit that displayed in the device status. 4. Click OK. 8.7.2 Configure Other Parameters After adding the access control device, you can set its parameters such as network parameters, capture parameters, RS-485 parameters, Wiegand parameters, etc. Set Parameters for Face Recognition Terminal For face recognition terminal, you can set its parameters including face picture database, QR code authentication, etc.
DS-K3B961TX Series Swing Barrier User Manual Save Authenticating Face Picture If enabled, the captured face picture when authenticating will be saved on the device. MCU Version View the device MCU version. 5. Click Save. Set RS-485 Parameters You can set the access control device's RS-485 parameters including the baud rate, data bit, the stop bit, parity type, flow control type, communication mode, work mode, and connection mode.
DS-K3B961TX Series Swing Barrier User Manual 3. Select an access control device in the device list and click Wiegand to enter the Wiegand Settings page. 4. Set the switch to on to enable the Wiegand function for the device. 5. Select the Wiegand channel No. and the communication mode from the drop-down list. Note If you set Communication Direction as Sending, you are required to set the Wiegand Mode as Wiegand 26 or Wiegand 34. 6. Click Save.
DS-K3B961TX Series Swing Barrier User Manual 8.8.1 Control Door Status You can control the status for the door(s), including unlock door, locking door, remaining the door unlock, remaining the door locked, remain all unlocked, etc. Before You Start ● Add person and assign access authorization to designed person, and person will have the access authorization to the access points (doors). For details, refer to Person Management and Set Access Group to Assign Access Authorization to Persons .
DS-K3B961TX Series Swing Barrier User Manual All doors in the group will be closed and locked. No person can access the doors even if he/she has the authorized credentials, except the super users. Capture Capture a picture manually. Note The Capture button is available when the device supports capture function. The picture is saved in the PC running the client. For setting the saving path, refer to .
DS-K3B961TX Series Swing Barrier User Manual 2. Optional: Select an access point group from the drop-down list in the upper-right corner to show the real time access records of the selected group. 3. Optional: Check the event type and event status. The detected events of checked type and status will be displayed in the list below. 4. Optional: Check Show Latest Event to view the latest access record. The record list will be listed reverse chronologically. 5.
DS-K3B961TX Series Swing Barrier User Manual Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.
DS-K3B961TX Series Swing Barrier User Manual Appendix B. DIP Switch B.1 DIP Switch Description The DIP switch is on the main user extended interface board. No.1 to No 4 is from the low bit to the high bit. Figure B-1 DIP Switch When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. B.2 DIP Switch Corresponded Functions Note After setting the DIP switch, you should reboot the device, or the function cannot take effect.
DS-K3B961TX Series Swing Barrier User Manual Bit 1 2 Device Mode Work Mode Keyfob Paring Mode Function Decimal Value Normal Mode 0 Study Mode 1 Disable Keyfob Paring Mode 0 Enable Keyfob Paring Mode 1 108 DIP Switch Address Diagram
DS-K3B961TX Series Swing Barrier User Manual Appendix C.
DS-K3B961TX Series Swing Barrier User Manual Appendix D. Error Code Description The swing barrier will display the error code on the seven-segment display if error occurred. Refer to the table below to find the description of each number.
DS-K3B961TX Series Swing Barrier User Manual Error Reason Lower Second IR Beam Triggered Code 18 Error Reason Code Obstruction 55 Lower Third IR Beam Triggered 19 Exceeding Studying Range 56 Lower Fourth IR Beam Triggered Motor Exception 57 20 111
DS-K3B961TX Series Swing Barrier User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD27483B
