Video Intercom D Series Door Station User Manual
Video Intercom D Series Door Station User Manual Legal Information ©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom D Series Door Station User Manual CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Video Intercom D Series Door Station User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom D Series Door Station User Manual Safety Instruction Warning • All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. • Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. • Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
Video Intercom D Series Door Station User Manual • Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. • Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. • Please keep all wrappers after unpack them for future use.
Video Intercom D Series Door Station User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom D Series Door Station User Manual ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 énoncée dans un autre environnement.cette eqipment devrait être installé et exploité avec distance minimale de 20 entre le radiateur et votre corps.
Video Intercom D Series Door Station User Manual Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Video Intercom D Series Door Station User Manual Contents 1 Appearance Description ............................................................................. 1 1.1 Appearance of 80 Series Door Station .............................................................. 1 1.2 Appearance of 81 Series Door Station .............................................................. 2 1.3 Appearance of 30 Series Door Station ..............................................................
Video Intercom D Series Door Station User Manual 3.3.1 Gang Box of 30 Series Door Station ........................................................ 19 3.3.2 Flush Mounting with Gang Box .............................................................. 19 4 Activation ................................................................................................. 22 4.1 Activate Device Locally .................................................................................... 22 4.
Video Intercom D Series Door Station User Manual 6.4 Parameters Settings ........................................................................................ 32 6.4.1 Local Parameters Settings ....................................................................... 32 6.4.2 System Settings ....................................................................................... 34 6.4.3 Network Settings .................................................................................... 36 6.4.
Video Intercom D Series Door Station User Manual 7.6.4 Get Person Information from Device ...................................................... 59 7.6.5 Change Person to Other Organization .................................................... 60 7.6.6 Add Person in Batch ................................................................................ 60 7.6.7 Issue Card in Batch ................................................................................. 61 7.6.8 Permission Settings ...................
Video Intercom D Series Door Station User Manual 1 Appearance Description Figure 1-1 Appearance of 80 Series Door Station Table 1-1 Descriptions No. Description No.
Video Intercom D Series Door Station User Manual Figure 1-2 Appearance of 81 Series Door Station Table 1-2 Descriptions No. Descripiton No.
Video Intercom D Series Door Station User Manual Table 1-3 Descriptions No. Description No.
Video Intercom D Series Door Station User Manual 2 Terminal and Wiring Description 2.
Video Intercom D Series Door Station User Manual Name Interface Description 485A- LOCK1 LOCK2 ALARM OUT` GND Grounding NO1 Door Lock Relay Output (NO) COM1 Common Interface NC1 Door Lock Relay Output (NC) NO2 Door Lock Relay Output (NO) COM2 Common Interface NC2 Door Lock Relay Output (NC) AO1+ Alarm Relay Output 1 AO1AO2+ Alarm Relay Output 2 AO2WIEGAND RESERVED TAMP Tamper-proof Input of Wiegand Card Reader OK Card Reader Indicator Output (Valid Card Output) ERR Card Reader
Video Intercom D Series Door Station User Manual Name POWER Interface Description RES Reserved 12 VDC DC 12 V Power Supply Input 2.2 Wiring Description 2.2.1 D-Series Door Lock Wiring Figure 2-2 Door Lock Wiring Note • Terminal NC1/COM1 is set as default for accessing electric bolt. Terminal NO1/ COM1 is set as default for accessing electric strike.
Video Intercom D Series Door Station User Manual Figure 2-3 Door Contact Wiring Note Terminal SEN1/SEN2 can both connect to door contact. 2.2.
Video Intercom D Series Door Station User Manual Figure 2-4 Exit Button Wiring Note Terminal BTN1/BTN2 can both connect to exit button. 2.2.4 External Card Reader Wiring Note • Please set the DIP switch first before connecting the card reader. • If the DIP switch should be configured when the card reader is power-on, please reboot the card reader after configuring the DIP switch. • The DIP switch description is shown in the following table: Table 2-2 DIP Switch Description No.
Video Intercom D Series Door Station User Manual No. Description How to Configure OFF: RS-485 7 Set the Wiegand protocol (It is ON: Wiegand 26 invalid when setting OFF in 6.) OFF: Wiegand 34 RS-485 Card Reader Wiring Figure 2-5 RS-485 Card Reader Wiring Note When card reader is accessed via RS-485, the door station cannot connect to elevator controller.
Video Intercom D Series Door Station User Manual Wiegand Card Reader Wiring Figure 2-6 Wiegand Card Reader Wiring 2.2.5 D-Series Elevator Controller Wiring Enter a short description of your concept here (optional). This is the start of your concept. 2.2.
Video Intercom D Series Door Station User Manual Figure 2-7 Alarm Input Wiring Diagram 2.2.
Video Intercom D Series Door Station User Manual Figure 2-8 Alarm Output Wiring Diagram 12
Video Intercom D Series Door Station User Manual 3 Installation • Make sure the device in the package is in good condition and all the assembly parts are included. • The power supply the door station support is 12 VDC. Please make sure your power supply matches your door station. • Make sure all the related equipment is power-off during the installation. • Check the product specification for the installation environment.
Video Intercom D Series Door Station User Manual Figure 3-2 Drill an Installation Hole 2. Insert the gang box into the hole and fix it with 4 PA4 screws.
Video Intercom D Series Door Station User Manual 3. Make sure the edges of the gang box align to the wall and the hook A and hook B of the gang box hook onto the wall. 4. Route the cables of the door station through the cable hole. 5. Insert the door station into the gang box and then move the door station downward to hook the lock catches on the rear panel onto the hook C of the gang box. Figure 3-4 Insert the Door Station 6. Fix the door station with 2 PM3 screws. 7.
Video Intercom D Series Door Station User Manual Figure 3-5 Fix the Door Station To install the door station onto the wall, you are required to use a matched gang box. Figure 3-6 Gang Box Note • The dimension of gang box is: 404 (W) × 123 (H) × 47.5 (D) mm. • The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Video Intercom D Series Door Station User Manual 3.2.2 Flush Mounting with Gang Box Steps 1. Drill a hole in the wal for inserting the gang box. The size of the hole should be larger than that of the gang box. The suggested size of the hole is 404.5 (W) × 123.5 (H) × 48 (D) mm. Figure 3-7 Drill an Installation Hole 2. Insert the gang box into the hole and fix it with 4 PA4 screws. Make sure the edges of the gang box align to the wall. Figure 3-8 Insert the Gang Box 3.
Video Intercom D Series Door Station User Manual 4. Put the door station into the gang box and hook the lock catches on the rear panel. Figure 3-9 Install the Door Station 5. Pull the door station downward and then push it towards the inside to make sure it fits the hole. 6. Tighten the screws of the door station with the wrench. Figure 3-10 Fix the Door Station To install the door station onto the wall, you are required to use a matched gang box.
Video Intercom D Series Door Station User Manual Figure 3-11 Gang Box Note • The dimension of gang box is: 343 (W) × 113 (H) × 55 (D) mm. • The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension. 3.3.2 Flush Mounting with Gang Box Steps 1. Drill a hole in the wall for inserting the gang box. The size of the hole should be larger than that of the gang box. The suggested size of the hole is 343.5 (W) × 113.5 (H) × 55.5 (D) mm.
Video Intercom D Series Door Station User Manual Figure 3-12 Drill an Installation Hole 2. Insert the gang box into the hole and fix it with 4 PA4 screws. 3. Make sure the edges of the gang box align to the wall. 4. Route the cables of the door station through the cable hole. 5. Put the door station into the gang box. 6. Fix the door station to the gang box with 4 screws.
Video Intercom D Series Door Station User Manual Figure 3-13 Fix the Door Station 21
Video Intercom D Series Door Station User Manual 4 Activation 4.1 Activate Device Locally You are required to activate the device first by settings a strong password for it before you can use the device. Steps 1. Power on the device to enter the activation page automatically. 2. Create a password and confirm it. Table 4-1 Number Button Description No. Description No. Description 1 1,.
Video Intercom D Series Door Station User Manual Note • The password required 8 to 16 characters. • The way to enter the password, take button 2 as an example: Press 2 to enter the number '2' or hold 2 for 1.5 s and press 2 again to enter the character 'a'. • When you have entered the password, press # to switch to confirm the password. • Press * to delete the wrong charater. 3. Press # to activate. 4.
Video Intercom D Series Door Station User Manual Note • When the device is not activated, the basic operation and remote operation of device cannot be performed. • You can hold the Ctrl or Shift key to select multiple devices in the online devices, and click the Activate button to activate devices in batch. 4.3 Activate Device via Web You are required to activate the device first by setting a strong password for it before you can use the device.
Video Intercom D Series Door Station User Manual 5 Local Operation 5.1 Local Configuration 5.1.1 Edit Network Parameters After activating, you should edit the network parameters. Steps 1. Hold * and # at the same time to enter the authentication page. 2. Authenticate via administrator. - Authenticate face/card/fingerprint to login. - Press # to enter the password to login. 3. Swritch to Network settings according to the tips on the page. Press # to enter the settings page. 4.
Video Intercom D Series Door Station User Manual 5. After configuration, press * to save and exit. 5.1.3 Add Residents User Management You can add, edit and delete the informations of the users. Steps 1. Hold * and # at the same time to enter the authentication page. 2. Authenticate via administrator. - Authenticate face/card/fingerprint to login. - Press # to enter the password to login. 3. Switch to User Management according to the tips on the page. 4. Press # to enter the settings page.
Video Intercom D Series Door Station User Manual Note • Press * to capture again. • Up to 5000 face pictures can be added to the device. Refers to the actual model. • Each user can add one face picture only. 5. Add fingerprints. 1) Switch to the fingerprint and press #. 2) Select +Add Fingerprint and press # to add. 3) Put your finger on the fingerprint recognition area. 4) Press * to save and exit. Note Up to 10 fingerprints can be added to the same user. 6.
Video Intercom D Series Door Station User Manual Call Resident from Main/Sub Door Station Press any digit button on the main/sub door station page to enter the calling page. Enter the room No. and press call button. Call Resident from Outer Door Station Press call button on the outer door station page to enter the calling page . Enter 【Building No. + # + Unit No. + # + Room No.】 and press call button to call resident. 5.2.
Video Intercom D Series Door Station User Manual Enter 【# + Public Password + #】to unlock the door. 5.3.2 Unlock by Presenting Card Note Make sure you have issued the card to the device. Present the card on the card reading area to unlock. Note You cannot unlock the door by presenting the main card. 5.3.3 Unlock by Fingerprint Note • Make sure you have added the fingerprint to the device. • Fingerprint function may vary with different modules. Please refer to the actual devices.
Video Intercom D Series Door Station User Manual 5. Press Scan QR Code on the main page to enter the scanning page. 6. Use the camera to scan the QR code. Note • Choose a location that will not reflect light when installing the door station, and tear off surface film of the acrylic door station. • Align the QR code with the camera horizontally when scanning the QR code. • QR code scanning is not supported at night.
Video Intercom D Series Door Station User Manual 6 Remote Configuration via Web 6.1 Live View In the browser address bar, enter the IP address of the device, and press the Enter key to enter the login page. Enter the user name and password and click Login to enter the Live View page. Or you can click Live View to enter the page. Figure 6-1 Live View • You can start/stop live view, capture, record, audio on/off, two-way audio, etc. • The stream type can be set as main stream or sub stream.
Video Intercom D Series Door Station User Manual 6.3 Device Management You can manage the linked device on the page. Click Device List to enter the settings page. Add Device • Click Add to add the indoor station or sub door station. Enter the parameters and click OK to add. • Click Import. Enter the information of the device in the template to import devices in batch. Export Click Export to export the information to the PC. Upgrade • Click Upload Package to select the upgrade package.
Video Intercom D Series Door Station User Manual You can configure the parameters of the live view, record files and captured pictures. The record files and captured pictures are the ones you record and capture by using the web browser. You can also set and view the saving paths of the captured pictures and recorded videos on the PC that running the web browser. Live View Parameters Stream Type Set the stream type as Main Stream or Sub-stream.
Video Intercom D Series Door Station User Manual 6.4.2 System Settings Follow the instructions below to configure the system settings, include System Settings, Maintenance, Security, and User Management, etc. Click System to enter the settings page. Basic Information Click System Settings → Basic Information to enter the settings page. On the page, you can edit Device Name and Device No. Set the Language and System Type according to your needs. Click Save to enable the settings.
Video Intercom D Series Door Station User Manual Figure 6-2 Maintenance • Reboot: Click Reboot to reboot the device. • Restore Click Restore to reset all the parameters, except the IP parameters and user information, to the default settings. Default Click Default to restore all parameters to default settings. • Export parameters: 1. Click Device Parameters to pop up the dialog box. 2. Set and confirm the encryption password. 3. Click OK to export parameters. • Import Config. File: 1.
Video Intercom D Series Door Station User Manual Note We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product.
Video Intercom D Series Door Station User Manual Figure 6-4 TCP/IP Settings 2. Configure the network parameters. - Check DHCP, the device will get the parameters automatically. - Set the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway manually. 3. Configure the DNS server. 4. Click Save to enable the settings. Port Settings Steps 1. Click Network → Basic Settings → Port to enter the settings page. Figure 6-5 Port Settings 2. Set the ports of the device.
Video Intercom D Series Door Station User Manual The default port number is 554 and it can be changed to any port No. ranges from 1 to 65535. Server Port The default server port number is 8000, and it can be changed to any port No. ranges from 2000 to 65535. 3. Click Save to enable the settings. SIP Setting Steps 1. Click Network → Basic Settings → SIP to enter the settings page. 2. Check Enable VOIP Gateway. 3. Configure the SIP parameters. 4. Click Save to enable the settings.
Video Intercom D Series Door Station User Manual Figure 6-6 SNMP Settings 2. Check the checkbox of Enable SNMPv1, Enable SNMP v2c, Enable SNMPv3 to enable the feature correspondingly. 3. Configure the SNMP settings. 4. Click Save to enable the settings. Note To lower the risk of information leakage, you are suggested to enable SNMP v3 instead of SNMP v1 or v2.
Video Intercom D Series Door Station User Manual Steps 1. Click Network → Advanced Settings → FTP to enter the settings page. Figure 6-7 FTP Settings 2. Check Enable FTP. 3. Select Server Type. 4. Input the Server IP Address and Port. 5. Configure the FTP Settings, and the user name and password are required for the server login. 6. Set the Directory Structure, Parent Directory and Child Directory. 7. Set the picture naming rules. 8. Click Save to enable the settings.
Video Intercom D Series Door Station User Manual 6.4.4 Video & Audio Settings Video Parameters Steps 1. Click Video/Audio → Video to enter the settings page. Figure 6-8 Video Parameters 2. Select the Stream Type. 3. Configure the video parameters. Stream Type Select the stream type to main stream or sub stream. Video Type Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio.
Video Intercom D Series Door Station User Manual Select the resolution of the video output. Bitrate Type Select the bitrate type to constant or variable. Video Quality When bitrate type is selected as Variable, 6 levels of video quality are selectable. Frame Rate Set the frame rate. The frame rate is to describe the frequency at which the video stream is updated and it is measured by frames per second (fps).
Video Intercom D Series Door Station User Manual Stream Type Select the stream type to main stream or sub stream. Audio Encoding The device support G.711ulaw and G.711 alaw. 3. Adjust the Input Volume, Output Volume and Speak Volume. Note Available range of volume: 0 to 10. 4. Click Save to save the settings. 6.4.5 Display Settings Configure the image adjustment, backlight settings and other parameters in display settings. Steps 1. Click Image → Display Settings to enter the display settings page.
Video Intercom D Series Door Station User Manual Brightness describes bright of the image, which ranges from 1 to 100. Contrast Contrast describes the contrast of the image, which ranges from 1 to 100. Saturation Saturation describes the colorfulness of the image color, which ranges from 1 to 100. Sharpness Sharpness describes the edge contrast of the image, which ranges from 1 to 100. BLC Area If you focus on an object against strong backlight, the object will be too dark to be seen clearly.
Video Intercom D Series Door Station User Manual Figure 6-11 Motion Detection 2. Check Enable Motion Detection to enable the function. 3. Click Draw Area.Click and drag the mouse on the live video to draw a motion detection area. Click Stop Drawing to finish drawing one area. Click Save to save the settings. Clear Area Click Clear All to clear all of the areas. Adjust Sensitivity Move the slider to set the sensitivity of the detection. 4. Click Arming Schedule to edit the arming schedule. 5.
Video Intercom D Series Door Station User Manual Notify Surveillance Center Send an exception or alarm signal to the remote management software when an event occurs. 7. Click Save to enable the settings. Set Video Tampering Alarm When the configured area is covered and cannot be monitored normally, the alarm is triggered and the device takes certain alarm response actions. Steps 1. Click Event → Basic Event → Video Tampering to enter the settings page. 2. Check Enable Video Tampering. 3. Draw area.
Video Intercom D Series Door Station User Manual Figure 6-12 Event Linkage 2. Select the Major Type as Device Event or Door Event. 3. Select the type of the Normal Linkage for the event. 4. Click Save to enable the settings. 6.4.
Video Intercom D Series Door Station User Manual Steps 1. Click Device ID Settings to enter the page. Figure 6-13 Device ID Settings 2. Select the device type from the drop-down list, and set the corresponding information. 3. Click Save to enable the device number configuration. Note • For main door station (D series or V series), the serial No. is 0. • For sub door station (D series or V series), the serial No. cannot be 0. Serial No. ranges from 1 to 99.
Video Intercom D Series Door Station User Manual Figure 6-14 Linked Network Settings 2. Set the master station IP address and master station SIP cllient Port. 3. Set the private SIP server IP address and private SIP Server Port. 4. Set the SIP Client Port. 5. Enter the password. 6. Click Save to enable the settings. Time Parameters Click Intercom → Time Parameters to enter the page. Configure the time parameters and click Save.
Video Intercom D Series Door Station User Manual Permission Password Steps 1. Click Access Control → Permission Password to enter the settings page. Figure 6-15 Permission Password 2. Select the password type. 3. Change the password. 4. Set the number of doorphone. 5. Click Save to enable the settings. Door Parameters Steps 1. Click Access Control → Door Parameters to enter the settings page.
Video Intercom D Series Door Station User Manual 2. Select the door and edit the door name. 3. Set door contact status. 4. Set lock action time. 5. Click Save to enable the settings. Card Security Click Access Control → Card Security to enter the settings page. Slide to enable card encryption parameters. Click Save to enable the settings. Elevator Control Before You Start • Make sure your door station is in the mode of main door station. Only the main door station support elevator control function.
Video Intercom D Series Door Station User Manual Figure 6-17 Elevator Control 2. Check to enable elevator control function. 3. Select an Elevator No., and select an elevator controller type for the elevator. 4. Set the Negative Floor. 5. Select the Interface Type as RS-485 or Network Interface. And enable the elevator control. - If you select RS-485, make sure you have connected the door station to the elevator controller with RS-485 wire.
Video Intercom D Series Door Station User Manual RS-485 Settings Set the working mode to linked device. Steps 1. Click Access Control → RS485 Settings to enter the settings page. Figure 6-18 RS-485 Settings 2. Select the No. 3. Select the working mode. 4. Click Save to enable the settings.
Video Intercom D Series Door Station User Manual 7 Configuration via Client Software 7.1 Edit Network Parameters To operate and configure the device via LAN (Local Area Network), you need connect the device in the same subnet with your PC. You can edit network parameters via iVMS-4200 client software. Steps 1. Select an online activated device and click the Modify Netinfo. 2. Edit the device IP address and gateway address to the same subnet with your computer. 3.
Video Intercom D Series Door Station User Manual Figure 7-1 Add to the Client 7.2.2 Add Device by IP Address Steps 1. Click +Add to pop up the adding devices dialog box. 2. Select IP/Domain as Adding Mode. 3. Enter corresponding information. 4. Click Add. 7.2.
Video Intercom D Series Door Station User Manual You can add many devices at once whose IP addresses are among the IP segment. Steps 1. Click +Add to pop up the dialog box. 2. Select IP Segment as Adding Mode. 3. Enter corresponding information, and click Add. 7.3 Remote Configuration Select the device, click to configure the parameters remotely. 7.4 Device Management Device management includes device activation, adding device, editing device, and deleting device, and so on.
Video Intercom D Series Door Station User Manual Note Up to 10 levels of organizations can be created. 7.5.2 Modify and Delete Organization You can select the added organization and click to modify its name. You can select an organization, and click X button to delete it. Note • The lower-level organizations will be deleted as well if you delete an organization. • Make sure there is no person added under the organization, or the organization cannot be deleted. 7.
Video Intercom D Series Door Station User Manual 1) Enter basic information: name, gender, tel, birthday details, effective period and email address. Note The length of person name should be less than 15 characters. 2) Click Add face to upload the photo. Note The picture should be in *.jpg format. Click Upload Select the person picture from the local PC to upload it to the client. Click Take Phone Take the person's photo with the PC camera.
Video Intercom D Series Door Station User Manual 7.6.2 Modify and Delete Person Select the person and click Edit to open the editing person dialog. To delete the person, select a person and click Delete to delete it. Note If a card is issued to the current person, the linkage will be invalid after the person is deleted. 7.6.3 Import and Export Person Information The person information can be imported and exported in batch. Steps 1.
Video Intercom D Series Door Station User Manual Steps Note This function is only supported by the device the connection mothod of which is TCP/IP when adding the device. 1. In the organization list on the left, click to select an organization to import the persons. 2. Click Get from Device to pop up the dialog box. 3. The added device will be displayed. 4. Click to select the device and then click Get to start getting the person information from the device.
Video Intercom D Series Door Station User Manual Enter the result of your step here (optional). Example Enter an example that illustrates the current task (optional). What to do next Enter the tasks the user should do after finishing this task (optional). 7.6.7 Issue Card in Batch You can issue multiple cards for the person with no card issued in batch. Steps 1. Click Batch Issue Cards to enter the dialog page. All the added person with no card issued will display in the Person(s) with No Card Issued list.
Video Intercom D Series Door Station User Manual Figure 7-3 Card Settings 3. Select Card Type and Card No. Type. 4. Click OK to save the settings. Result After issuing the card to the person, the person and card information will display in the Person(s) with Card Issued list. 7.6.8 Permission Settings Add Permissions Steps 1. On the main page, click page. AccessControlInfo → Access Group to enter the 2. Click +Add to pop up the adding dialog box. 3. Configure the parameters.
Video Intercom D Series Door Station User Manual 2) Select the Template of the schedule. 3) Check the person to Selected according to your needs. 4) Check the device to Selected according to your needs. 4. Click Save. 5. Check the permission and click Apply All to Device. The status of the permission displays as Applied. 6. Optional: Click Applying Status to check the details. Modify/Delete Permissions On the page of the permission settings, click permission.
Video Intercom D Series Door Station User Manual • Click to adjust the volume of the loudspeaker. • Click to adjust the volume of the microphone. • Click Hang Up to hang up the dialog. • Click to open the door remotely. Note • One video intercom device can only connect with one client software. • The maximum ring duration can be set from 15s to 60s via the Remote Configuration of the video intercom device.
Video Intercom D Series Door Station User Manual 4. Edit the Subject, Type and Information. 5. Click View to select the picture. 6. Click Send. Note • Up to 63 characters are allowed in the Subject field. • Up to 6 pictures in the JPGE format can be added to one notice. And the maximum size of one picture is 512KB. • Up to 1023 characters are allowed in the Information field. 7.7.4 Search Video Intercom Information Search Call Logs Steps 1. On the Video Intercom page, click Call Log to enter the page.
Video Intercom D Series Door Station User Manual Click ˅ to unfold the drop-down list and select the device type as Indoor Station, Door Station, Outer Door Station or Analog Indoor Station. Or select All Devices to search logs with all device types. Start Time/End Time Click the time icon to specify the start time and end time of a time period to search the logs. Reset the Settings Click Reset to reset all the configured search conditions. 3.
Video Intercom D Series Door Station User Manual A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD19922B
2 3 Note: The appearance of the device vary according to different model. Refers to the actual device. 2 Terminal DC 12 V: Power Supply Input AO1+/AO1- : Alarm Relay Output 1 AO2+/AO2- : Alarm Relay Output 2 NC1/NC2: Door Lock Relay Output (NC) NO1/NO2: Door Lock Relay Output (NO) COM1/COM2: Common Interface AIN1/AIN2/AIN3/AIN4: Alarm Input BTN1/BTN2: Door Contact Detection Input/Exit Button SEN1/SEN2: Door Contact Detection Input/Door Contact Note: Wiring description refers to the User Manual.
ENGLISH ENGLISH ENGLISH ENGLISH Diagram References Diagram References Diagram References Diagram References ENGLISH ENGLISH ENGLISH ENGLISH Diagram References Diagram References Diagram References Diagram References
ENGLISH ENGLISH ENGLISH ENGLISH Diagram References Diagram References Diagram References Diagram References ENGLISH ENGLISH ENGLISH ENGLISH Diagram References Diagram References Diagram References Diagram References Hangzhou Hikvision Digital Technology CO.,Ltd. No.
©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/).
