Video Intercom Face Recognition Door Station User Manual
Video Intercom Face Recognition Door Station User Manual Legal Information ©2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Video Intercom Face Recognition Door Station User Manual CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
Video Intercom Face Recognition Door Station User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Video Intercom Face Recognition Door Station User Manual Safety Instruction Warning ● ● ● ● All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Please make sure that the power has been disconnected before you wire, install or dismantle the device.
Video Intercom Face Recognition Door Station User Manual ● ● ● Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or leakage of flammable liquid or gas. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. Used batteries may result in pollution to the environment. Dispose of used batteries according to the instructions provided by the battery manufacturer.
Video Intercom Face Recognition Door Station User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Video Intercom Face Recognition Door Station User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/ 65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Video Intercom Face Recognition Door Station User Manual 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
Video Intercom Face Recognition Door Station User Manual Contents 1 About this Manual ...................................................................................... 1 2 Appearance ................................................................................................ 2 2.1 Door Station ...................................................................................................... 2 2.2 Door Station with Keypad Module ..................................................................
Video Intercom Face Recognition Door Station User Manual 7 Local Configuration ................................................................................... 21 7.1 Quick Configuration ........................................................................................ 21 7.2 Authentication via Admin ............................................................................... 26 7.3 Network Parameters Settings .......................................................................... 27 7.3.
Video Intercom Face Recognition Door Station User Manual 8.2.2 Unlock by Face ........................................................................................ 42 8.2.3 Unlock by Presenting Card ...................................................................... 42 8.2.4 Unlock by QR Code ................................................................................. 42 9 Remote Configuration via Web ................................................................ 44 9.1 Live View .............
Video Intercom Face Recognition Door Station User Manual 10.2.3 Add Device via IP segment ................................................................... 82 10.2.4 Add Devices in Batch ............................................................................ 82 10.2.5 Add Device Via EHome ......................................................................... 83 10.3 Local Configuration via Client Software ........................................................ 83 10.4 Device Management ..........
Video Intercom Face Recognition Door Station User Manual 1 About this Manual Get the manual and related software from or the official website (http:// www.hikvision.com).
Video Intercom Face Recognition Door Station User Manual 2 Appearance 2.1 Door Station Note Refers to the specific model for the appearance of the device. Figure 2-1 Door Station Table 2-1 Appearance Description No. Description No.
Video Intercom Face Recognition Door Station User Manual No. Description No. Description Note The debugging port is used for debugging only. 5 Microphone 11 MicroUSB Interface Note Micro USB interface is used for debugging only. 6 Camera 12 TF Card Slot 2.2 Door Station with Keypad Module Note Refers to the specific model for the appearance of the device.
Video Intercom Face Recognition Door Station User Manual Figure 2-2 Door Station with Keypad Module Table 2-2 Appearance Description No. Description No. Description 1 Wiring Terminal 8 Button 2 Network Interface 9 TAMPER 3 Analog & RS-485 Interface 10 Loudspeaker 4 IR Supplement Light Debugging Port 11 Note The debugging port is used for debugging only. 5 Microphone 12 MicroUSB Interface Note MicroUSB interface is used for debugging only.
Video Intercom Face Recognition Door Station User Manual No. Description No. Description 6 Camera 13 TF Card Slot 7 Ambient Light Sensor 2.3 Door Station with Fingerprint Module Note Refers to the specific model for the appearance of the device. Figure 2-3 Door Station with Fingerprint Module Table 2-3 Appearance Description No. Description No.
Video Intercom Face Recognition Door Station User Manual No. Description No. Description 3 Analog & RS-485 Interface 10 TAMPER 4 IR Supplement Light 11 Loudspeaker 5 Microphone 12 Debugging Port Note The debugging port is used for debugging only.
Video Intercom Face Recognition Door Station User Manual 3 Terminal and Wiring Description Door station can be wired to alarm input interface, alarm input interface, door lock, door contact and so on.
Video Intercom Face Recognition Door Station User Manual 4 Installation 4.1 Install Door Station Note ● ● ● ● ● Gang box is required for the installation of door station. The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. Complete wiring during installation. Refers toTerminal and Wiring Description for wiring details. Make sure all the related equipment is power-off during the installation.
Video Intercom Face Recognition Door Station User Manual Mounting Plate Figure 4-1 Mounting Plate Note The dimension of the mounting plate is 233 mm (W) × 112.4 mm (H) × 21 mm (D).
Video Intercom Face Recognition Door Station User Manual Gang Box Figure 4-2 Gang Box Note ● ● The dimension of the gang box is 236.9 mm (W) × 128.4 mm (H) × 40.8 mm (D). The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 237.5 mm (W) × 128.9 mm (H) × 41.3 mm (D). 4.1.2 Surface Mounting Steps 1. Paste the mounting template on the wall according to the installation location requirements.
Video Intercom Face Recognition Door Station User Manual Note ● ● Do not touch the SD card slot and other devices during the process of plugging in and unplugging the power interface. Apply Silicone sealant among the joints between the device and the wall (except the lower side) to keep the raindrop from entering. Figure 4-3 Surface Mounting 4.1.3 Flush Mounting Steps 1. Cave an installation hole in the wall. The suggested dimension of the installation hole is 237.5 mm (W) × 128.9 mm (H) × 41.3 mm (D).
Video Intercom Face Recognition Door Station User Manual Figure 4-4 Flush Mounting 4.2 Install Door Station with Sub Module Note ● ● ● ● ● ● Gang box is required for the installation of door station. The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. Complete wiring during installation. Refers to Terminal and Wiring Description for wiring details. Make sure all the related equipment is power-off during the installation.
Video Intercom Face Recognition Door Station User Manual Mounting Plate Figure 4-5 Mounting Plate Note The dimension of the mounting plate is 233 mm (W) × 112.4 mm (H) × 21 mm (D).
Video Intercom Face Recognition Door Station User Manual Gang Box Figure 4-6 Gang Box Note ● ● The dimension of the gang box is 312.9 mm (W) × 128.4 mm (H) × 40.8 mm (D). The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 313.5 mm (W) × 128.9 mm (H) × 41.3 mm (D). 4.2.
Video Intercom Face Recognition Door Station User Manual Steps 1. Loosen splice set screws, and separate the host from the keypad module. Paste the mounting template on the wall according to the installation location requirements. Drill holes according to the location of the screw holes of the drill template, and install the expansion bolts into the screw holes. 2. Fix the mounting plate to the wall with 4 supplied screws. 3. Fix the device to the mounting plate, and fix the device with the set screws. 4.
Video Intercom Face Recognition Door Station User Manual wall, insert the gang box into the installation hole, and mark the gang box screw holes' position with a marker. 2. Take out the gang box. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. Fix the gang box with 4 expansion bolts. Remove the mounting ears of the gang box. 3. Fix the sub module to the door station with 2 set screws. Wire the device and cover the rear panel with 2 screws.
Video Intercom Face Recognition Door Station User Manual 5 Sub Module Description Both keypad module and fingerprint module are supported by the door station. Select a sub module according to your actual needs. Figure 5-1 Keypad Module Figure 5-2 Fingerprint Module After installation, power on the device. Door station will recognize the sub module automatically. Device will restart automatically in 10 s when the sub module is removed from the door station.
Video Intercom Face Recognition Door Station User Manual 6 Activation 6.1 Activate Device Locally You are required to activate the device first by settings a strong password for it before you can use the device. Steps 1. Power on the device to enter the activation page automatically. 2. Create a password and confirm it. Note You can tap to enable or disable password reveal. 3. Tap Next to finish activation.
Video Intercom Face Recognition Door Station User Manual Caution In order to improve the network security, the set password must be from 8 to 16 digits, and be a combination of at least two or more types of numbers, lowercase letters, uppercase letters, and special characters. 3. If there are multiple door stations in your network, please edit the IP address of the door station to prevent IP address conflicts from causing abnormal access to the door station.
Video Intercom Face Recognition Door Station User Manual Note ● ● When the device is not activated, the basic operation and remote operation of device cannot be performed. You can hold the Ctrl or Shift key to select multiple devices in the online devices, and click the Activate button to activate devices in batch. 6.4 Activate Device via Web You are required to activate the device first by setting a strong password for it before you can use the device.
Video Intercom Face Recognition Door Station User Manual 7 Local Configuration 7.1 Quick Configuration After activating the device, the quick configuration page will pop up automatically. Steps 1. Select the system language and tap NEXT. Figure 7-1 Select Language 2. Set network parameters and tap NEXT. - Set the IP address, Subnet Mask and Gateway manually. - Enable DHCP, the device will get network parameters automatically.
Video Intercom Face Recognition Door Station User Manual Figure 7-2 Network Parameters Settings 3. Set password reset method and tap NEXT. - Enter the Reserved Email address, then you can reset the admin password by email. Note On the security questions settings page, you can tap Change to Reserved Email to modify the password reset method.
Video Intercom Face Recognition Door Station User Manual Figure 7-3 Password Reset by Setting Reserved Email Address - Tap Change to Security Question. Select 3 security questions from deficiency list and enter the answers of the questions, then you can reset the password by answering security questions.
Video Intercom Face Recognition Door Station User Manual Figure 7-4 Password Reset by Setting Security Questions 4. Enable the cloud service functions and create a verification code. Tap NEXT.
Video Intercom Face Recognition Door Station User Manual Figure 7-5 Cloud Service 5. Select theme of the system.
Video Intercom Face Recognition Door Station User Manual Figure 7-6 Theme Settings 6. Tap FINISH. 7.2 Authentication via Admin You can configure the parameters of the device on the menu page. You should authenticate to enter the menu. If you want to authenticate via face/card/fingerprints, you should add administrator first. Refers to User Management for details. Steps 1. Hold the screen to enter the authentication page. 2.
Video Intercom Face Recognition Door Station User Manual Figure 7-7 Menu Page 7.3 Network Parameters Settings The device support wired network, wireless network and cloud service settings. Note Only parts of the devices support the wireless network, please refers to the actual device for detailed information. 7.3.1 Edit Wired Network Parameters The device should be connected to the network. Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details.
Video Intercom Face Recognition Door Station User Manual Steps 1. On the menu, tap Network → Wired Network to enter the settings page. Figure 7-8 Wired Network Settings 2. Edit the wired network parameters. - Edit the wired network parameters manually. - Enable DHCP, and the system will get the parameters automatically. 7.3.2 Cloud Service Settings Enable the function, you can configure and operate the device via mobile client remotely. Before You Start Authenticate and enter the menu first.
Video Intercom Face Recognition Door Station User Manual Figure 7-9 Cloud Service Settings 2. Slide to enable the function. 3. Edit the Cloud Service Address and create a Verification Code. 4. Tap √ to save the settings. 7.4 Device No. Settings Configure the No. of the device to make the communitcation easily. Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details. Steps 1. On the menu, tap Local Configuration to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 7-10 Local Configuration 2. Edit Community No., Building No., Unit No., Floor No. and No. according to the actual needs. 7.5 User Management On the user management page, you can add new users, configure the user's room information, card information, face information, and fingerprint information. Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details. Steps 1.
Video Intercom Face Recognition Door Station User Manual 1) Tap Card, and tap + to enter the add card page. 2) Enter the card No. manually or present the card in the card presenting area to obtain the card No. 3) Tap OK to enable the settings. 5. Add Face. 1) Tap Face Picture, and point the face at the camera. 2) Tap to add the face. 3) Tap to enable the settings. 6. Add Fingerprint. 1) Select Fingerprint, and tap +. 2) Put your finger on the fingerprint reader and add the fingerprint. 7.
Video Intercom Face Recognition Door Station User Manual Figure 7-11 Local Configuration 2. Tap Shortcut Key to select call mode. Calling Menu Select call mode as Calling Menu. On the main page, tap call button to enter the calling page. Call Specified Room Select call mode as Call Specified Room and set the Specified Room No.. On the main page, tap call button to call the room you set. Call Center Select call mode as Call Center. On the main page, tap call button to call the management. 3.
Video Intercom Face Recognition Door Station User Manual Admin password is used for authenticating to enter the local configuration menu. If you forget the password, you can change it by entering security questions' answers. Steps 1. Hold the main page to enter the authentication page. Figure 7-12 Authentication Page 2. Tap Forgot Password. 3. Change the admin password via entering answers of security questions or email address. 4. Create and confirm a new password. 7.8 System Settings 7.8.
Video Intercom Face Recognition Door Station User Manual Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details. Steps 1. On the menu, tap Local Configuration to enter the settings page. Figure 7-13 Local Configuration 2. Tap Select Language to switch the system language. 7.8.2 Adjust Brightness Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details. Steps 1.
Video Intercom Face Recognition Door Station User Manual Figure 7-14 Local Configuration 2. Adjust the brightness of the device. - Enable the Auto Screen Brightness, the device will adjust the brightness according to the environment automatically. - Edit the number to adjust the brightness manually. 7.8.3 Keypad Sound Settings Authenticate and enter the menu first. Refers to Authentication via Admin for details. On the menu, tap Local Configuration to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details. Steps 1. On the menu, tap Local Configuration to enter the settings page. 2. Slide to enable the function. 7.8.5 Theme Settings Select theme of the system to make the device user friendly. Before You Start Authenticate and enter the menu first. Refers to Authentication via Admin for details. Steps 1.
Video Intercom Face Recognition Door Station User Manual Figure 7-15 Local Configuration 2. Restore the device. Restore to Default Settings Tap Restore to Default Settings to reset all parameters, except IP address, subnet mask and default gateway, to the default settings. Restore to Factory Settings Tap Restore to Factory Settings to restore all parameters to default settings. 7.9 Device Information View the device model, system version, App version and open source software licenses.
Video Intercom Face Recognition Door Station User Manual Steps 1. On the menu, tap About to enter the page. Figure 7-16 About 2. You can view the device model, system version, App version and open source software licenses. 3. Optional: Scan the QR code to add the device to mobile client.
Video Intercom Face Recognition Door Station User Manual 8 Local Operation 8.1 Call from the Device Door station supports calling users or management center. 8.1.1 Call Resident Call Resident from Main/Sub Door Station Figure 8-1 Call Resident On the main page, tap to enter the calling page. Enter the Room No., and tap to call residents.
Video Intercom Face Recognition Door Station User Manual Note ● ● Both the main and sub door station support the elevator control function, that is, after calling the residents successfully, tap the unlock button on the indoor station, the elevator will automatically arrive at the floor where the door station is located, and the permission of the floor where the household is located will be opened (The elevator calling will take effect only after the elevator control is configured and the corresponding c
Video Intercom Face Recognition Door Station User Manual Call Resident from Outer Door Station On the main page of the outer door station, tap Call to enter the calling page. Enter Phase No. + # + Building No. + # + Unit No. + # + Room No., and tap Call again to call residents. Enter Phase No. + # + Building No. + # + Unit No. + # + Room No., and tap Call again to call residents. Enter Phase No. + # + Building No. + # + Unit No. + # + Room No., and tap Call again to call residents. Enter Phase No.
Video Intercom Face Recognition Door Station User Manual Tap call button on the main page to enter the calling page. Enter 【 # + Password 】, and tap unlock button. 8.2.2 Unlock by Face Note Make sure that you have added your face picture to the device. Refers to the User Management for details. Face forward at the camera to unlock. 8.2.3 Unlock by Presenting Card Note Make sure you have issued the card to the device. Refers to User Management for details.
Video Intercom Face Recognition Door Station User Manual Note Operating environment of Hikvision Cloud Management ● iOS System: iOS 6.0 and above. ● Android System: Android 4.0 and above. Here takes Android system as an example. 2. Register user accounts according to the prompts, and login to the client software. 3. Follow the prompts to add the indoor station by scanning the QR code/barcode or manually entering the serial number. 4. Enter unlock by QR code page and generate the QR code. 5.
Video Intercom Face Recognition Door Station User Manual 9 Remote Configuration via Web 9.1 Live View In the browser address bar, enter the IP address of the device, and press the Enter key to enter the login page. Enter the user name and password and click Login to enter the Live View page. Or you can click Live View to enter the page. Figure 9-1 Live View ● You can start/stop live view, capture, record, audio on/off, two-way audio, etc. ● The stream type can be set as main stream or sub stream.
Video Intercom Face Recognition Door Station User Manual Figure 9-2 Add User 1) Enter Person ID, Name, Floor No.andRoom No.. Select Level. 2) Configure Start Time and End Time. 3) Check Administrator and the person added will be able to log in by face recognition. 4) Click Add Card, enter Card No. and select Property. Or you can click Read and place the card on the card-reding zone. 5) Click Capture and make sure the face image of the person can be captured properly.
Video Intercom Face Recognition Door Station User Manual You can manage the linked device on the page. Click Device Management to enter the settings page. Figure 9-3 Device Management Add Device ● ● Click Add to add the indoor station or sub door station. Enter the parameters and click OK to add. Click Import. Enter the information of the device in the template to import devices in batch. Note You can set related No. with uppercase letters (must be contained) and digits for indoor stations.
Video Intercom Face Recognition Door Station User Manual Upgrade Click Timing Upgrade, click to Enable Upgrading Device Automatically and configure Start Time and End Time. The devices will upgrade automatically at the set time. Click Upload Updating Package, select Upgrade File and click Browse to upload upgrading package. Select devices to be upgraded, and click Upgrade Now to upgrade devices manually. Upgrading Status Click Upgrading to view the upgrading status of the devices.
Video Intercom Face Recognition Door Station User Manual Click Configuration to set the parameters of the device. Remote configuration in iVMS-4200 and Batch Configuration Tool is the same as that in Web. Here takes the configuration in web for example. Note Run the browser, click Mode. → Internet Options → Security to disable the Protected 9.4.1 Local Settings Live View Parameters ● ● ● ● Stream Type: Select the stream type toMain StreamorSub Stream.
Video Intercom Face Recognition Door Station User Manual Note Only IE and Google browsers support saving path settings. Other browsers default to the C drive download path. Please refer to the actual device page for more details. 9.4.2 System Parameters Follow the instructions below to configure the system settings, include System Settings, Maintenance, Security, and User Management, etc. Click Configuration → System to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 9-4 Basic Information Click View QR Code, and you can use the mobile client to scan to add the device. You can view the quantities of added users, face pictures and cards in Capacity. Click Save to enable the settings. Time Settings Click Time Settings to enter the settings page. Select the Time Zone of your location from the drop-down list.
Video Intercom Face Recognition Door Station User Manual ● ● Enable NTP, set the Server Address, NTP Port and Interval. Enable Manual Time Sync., set the time manually or check the Sync. with computer time. Click Save to enable the settings. About Click About to enter the page. Click View Licenses to view open source software Licenses. Maintenance Enter a short description of your concept here (optional). Click Maintenance → Upgrade & Maintenance to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Restore All Click Restore All to reset all the parameters, except the IP parameters and user information, to the default settings. Unlink APP Account Click Unlink APP Account to unlink the account from the mobile client. Export Parameters 1. Select Device Parameters, and click Export to pop up the dialog box. 2. Set and confirm the encryption password. 3. Click OK to export parameters. Import Config File 1.
Video Intercom Face Recognition Door Station User Manual Steps 1. Click Security → Security Service to enter the settings page. Figure 9-6 Security Service 2. On the page, you can enable SSH, ADB remote control and HTTP according to your actual needs. 3. Click Save to enable the settings. Certificate Management It helps to manage the server/client certificates and CA certificate, and to send an alarm if the certificates are close to expiry date, or are expired/abnormal. Create Certificate Steps 1.
Video Intercom Face Recognition Door Station User Manual Steps 1. Select Certificate Type from the drop-list. 2. Click Browser and select the certificate files from the PC. 3. Click Install. Import Communication Certificates Steps 1. Select Certificate Type from drop-list. 2. Click Browser to select the certificate and click Install. Note ● Up to 16 certificates are allowed. ● If certain functions are using the certificate, it cannot be deleted.
Video Intercom Face Recognition Door Station User Manual 9.4.3 Network Settings TCP/IP Settings TCP/IP settings must be properly configured before you operate the device over network. The device supports IPv4. Steps 1. Click Network → Basic Settings → TCP/IP to enter the settings page. Figure 9-7 TCP/IP Settings 2. Select Network Card. 3. Configure the network parameters. - Check DHCP, the device will get the parameters automatically.
Video Intercom Face Recognition Door Station User Manual Steps 1. Click Network → Basic Settings → Port to enter the settings page. 2. Set the ports of the device. HTTP Port The default port number is 80, and it can be changed to any port No. which is not occupied. HTTPS Port The default port number is 443, and it can be changed to any port No. which is not occupied. RTSP Port The default port number is 554. Server Port The default server port number is 8000, and it can be changed to any port No.
Video Intercom Face Recognition Door Station User Manual Figure 9-8 SIP Settings 2. Check Enable VOIP Gateway. 3. Configure the SIP parameters. 4. Click Save to enable the settings. FTP Settings Steps 1. Click Network → Advanced → FTP to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 9-9 FTP Settings 2. Check Enable FTP. 3. Select Server Type. 4. Input the Server IP Address and Port. 5. Configure the FTP Settings, and the user name and password are required for the server login. 6. Set the Directory Structure, Parent Directory and Child Directory. 7. Set the picture naming rules.
Video Intercom Face Recognition Door Station User Manual 8. Click Save to enable the settings. Platform Access Platform access provides you an option to manage the devices via platform. Steps 1. Click Configuration → Network → Advanced Settings → Platform Access to enter the settings page. Figure 9-10 Platform Access 2. Select platform access mode. 3. Check Enable, configure the server IP address and set Access Server IP Address and Verification Code. 4. Click Save to enable the settings.
Video Intercom Face Recognition Door Station User Manual Click Configuration → Network → Advanced → HTTP Listening to enter the settings page. Figure 9-11 HTTP Listening Settings Enter the parameters according to the page and click Save to enable the function. Capture Network Packet Click Network → Capture Network Packet to enter the settings page. Slide to adjust the Capture Packet Duration and Capture Packet Size. Click Capture to get the network packet. 9.4.
Video Intercom Face Recognition Door Station User Manual Figure 9-12 Video Parameters 2. Select the Stream Type. 3. Configure the video parameters. Stream Type Select the stream type to main stream or sub stream. Video Type Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio. Resolution Select the resolution of the video output. Bitrate Type Select the bitrate type to constant or variable.
Video Intercom Face Recognition Door Station User Manual Set the max. bitrate from 32 to 16384 Kbps. The higher value corresponds to the higher video quality, but the better bandwidth is required. Video Encoding The device supports H.264. I Frame Interval Set I Frame Interval from 1 to 400. 4. Click Save to save the settings. Audio Parameters Steps 1. Click Video/Audio → Audio to enter the settings page. Figure 9-13 Audio Settings 2. Configure the stream type and the audio encoding type.
Video Intercom Face Recognition Door Station User Manual 9.4.5 Display Settings Configure the image adjustment, backlight settings and other parameters in display settings. Steps 1. Click Image → Display Settings to enter the display settings page. Figure 9-14 Display Settings 2. Select the Format. 3. Set the display parameters. WDR Wide Dynamic Range can be used when there is a high contrast of the bright area and the dark area of the scene.
Video Intercom Face Recognition Door Station User Manual Auto Figure 9-15 Day/Night Switch Select Day/Night Switch as Auto, and set the Sensitivity. The device will switch between Day Mode and Night Mode automatically according to the environment. Daytime Select Day/Night Switch as Daytime. The device will keep the mode as daytime. Night Select Day/Night Switch as Night. The device will keep the mode as night. Scheduled-Switch Select Day/Night Switch as Scheduled-Switch and set the duration.
Video Intercom Face Recognition Door Station User Manual Steps 1. Click Event → Motion to enter the settings page. Figure 9-16 Motion Detection 2. Slide Enable Motion Detection to enable the function. 3. Click Draw Area. Click and drag the mouse on the live video to draw a motion detection area. Click Save to save the settings. Clear Area Click X to clear all of the areas. Adjust Sensitivity Move the slider to set the sensitivity of the detection.
Video Intercom Face Recognition Door Station User Manual 5. Click on the time bar and drag the mouse to select the time period. Click Save to save the settings. Delete Schedule Click Delete to delete the current arming schedule. 6. Click Linkage Method to enable the linkages. Notify Surveillance Center Send an exception or alarm signal to the remote management software when an event occurs. 7. Click Save to enable the settings. Event Linkage Steps 1.
Video Intercom Face Recognition Door Station User Manual Figure 9-17 Event Linkage 2. Select the Major Type as Device Event or Door Event. 3. Select the Minor Type. - For device event, select Minor Type as Tampering Alaem, Fire Input Alarm or Fire Input Resume. - For door event, select Minor Type as Door Open Timed Out (Door Contact). 4. Select the type of the Normal Linkage for the event. 5. Click Save to enable the settings.
Video Intercom Face Recognition Door Station User Manual 9.4.7 Card Security Click General → Card Security to enter the settings page. Figure 9-18 Card Security Slide to enable card encryption parameters. Click Save to enable the settings. 9.4.8 Intercom Settings Device No. Configuration Set the No. of the device, and linked devices can build a communication. Steps 1. Click Intercom → Device No. to enter the settings page. Figure 9-19 Device No. Settings 2.
Video Intercom Face Recognition Door Station User Manual 3. Click Save to enable the device number configuration. Note ● ● ● ● For main door station (D series or V series), the serial No. is 0. For sub door station (D series or V series), the serial No. cannot be 0. Serial No. ranges from 1 to 99. For each villa or building, at least one main door station (D series or V series) should be configured, and one sub door stations (D series or V series) can be customized.
Video Intercom Face Recognition Door Station User Manual Figure 9-21 Password Settings 2. Click +Add to create a password. 1) Create a password. 2) Check to select unlock permission. 3) Optional: Enter the remarks of the password. 3. Click OK to save the password. Call Settings Click Intercom → Call Settings to enter the page. Configure the time parameters and click Save. Note ● ● For door station, maximum call duraion and maximum message duration should be configured.
Video Intercom Face Recognition Door Station User Manual Figure 9-22 Ringtone Settings Note Available Audio Format: WAV、AAC, Size: Less than 600 KB, Sample Rate: 8000Hz, Mono. Call Priority Enter a short description of your task here (optional). Before You Start Enter the prerequisites here (optional). Enter the context of your task here (optional). Steps 1. Click Intercom → Call Priority to enter the settings page. Figure 9-23 Call Priority 2.
Video Intercom Face Recognition Door Station User Manual Note The higher the level, the ealier the device to be called. After the call time is over, the next level of call is triggered. Number Settings Steps 1. Click Intercom → Number Settings , and you can view the No., room No., and SIP number. 2. Add the number. 1) Click Add. 2) Enter Room No., and SIP. 3) Optional: Click Add to add SIP according to the actual needs. 4) Click OK. 3. Optional: Click to edit the number. 9.4.
Video Intercom Face Recognition Door Station User Manual Figure 9-24 Door Parameters 2. Select Door No., and edit the Name. 3. Set Open Duration. When the time to open over the open duration you set, the door will be locked again. 4. Select Relay Reverse as ON or Disable. 5. Click Save to enable the settings. Elevator Control Before You Start Make sure that the door station is in the mode of main door station. Only the main door station supports elevator control function. Steps 1.
Video Intercom Face Recognition Door Station User Manual Figure 9-25 Elevator Control 2. Check to enable elevator control function. 3. Select an Elevator No., and select an elevator controller type for the elevator. 4. Select Interface Type. Note If you select Interface Type as RS-485, you only need to enter Negative Floor Capacity. 5. Enter Negative Floor Capacity, and select Alarm Receiver Type. 6. Enter the elevator controller's Server IP Address, Port No., User Name, and Password. 7.
Video Intercom Face Recognition Door Station User Manual Note ● Up to 4 elevator controllers can be connected to one door station. ● Up to 10 negative floors can be added. ● Make sure the interface types of elevator controllers, which are connected to the same door station are consistent. RS-485 Settings Set the working mode to linked device. Steps 1. Click Access Control → RS-485 to enter the settings page. Figure 9-26 RS-485 Settings 2. Select the No. 3. Select the working mode. 4.
Video Intercom Face Recognition Door Station User Manual Figure 9-27 Smart Settings Table 9-1 Face Capture Advanced Parameters Parameter Description Face Anti-spoofing Enable face anti-spoofing to detect real people face for recognition. After enabling face anti-spoofing function, you can set the Live Face Detection Security matching security level when performing live face Level authentication. Recognition Distance Set the valid distance between the user and the camera when authenticating.
Video Intercom Face Recognition Door Station User Manual Parameter Description Face Recognition Timeout Value When the face recognition time exceed the value you set, the recognition will be determined as a timeout operation. Note You can input the number from 1 to 20. ECO Settings After enabling the ECO mode, the device will use the IR camera to authenticate faces in the low light or dark environment. And you can set the ECO mode threshold, ECO mode (1:N).
Video Intercom Face Recognition Door Station User Manual Figure 9-28 Area Configuration Drag the frame or enter the digits behind the parameters to adjust the size of the recognition area. 9.4.11 Theme Settings Set the advertisement on the main page of the device. Steps 1. Click Configuration → Theme to enter the settings page.
Video Intercom Face Recognition Door Station User Manual Figure 9-29 Theme Settings 2. Check to enable screen saving function. 3. Set the advertisement theme. 1) Click + Add Theme. 2) Create a theme name, and select the advertisement body as picture or Video. 3) Click Save. 4. Click + to select a picture from the local as the material to be played in standby, and click upload. 5. Set the play schedule. 1) Select a theme and drag the time interval to be played on the timeline.
Video Intercom Face Recognition Door Station User Manual 7. Optional: Slide to enable show custom content and edit custom content. The custom content displays on the main page of the device. 8. Click Save.
Video Intercom Face Recognition Door Station User Manual 10 Remote Configuration via Client Software You can set Video Intercom system and manage video intercom products including indoor station, door station and main station via iVMS-4200 client software. 10.1 Edit Device Network Parameters Before You Start Before configuring the device remotely, make sure that the device is activated. Steps 1. On the person management page, click Online Device. 2. Click to pop up the network parameter settings page.
Video Intercom Face Recognition Door Station User Manual 4. Enter the device Name, User Name, Password, and click Add. Note ● ● Only when the doorphone is added to the client software, you can remotely configure the indoor station. Only online devices with the same user name and activation password can support batch activation. After the device is added, the device information will be listed in the device list area. 10.2.2 Add Device via IP Address Steps 1.
Video Intercom Face Recognition Door Station User Manual 4. Select the file and click Add to import. Note The file format for batch import is .csv format. 10.2.5 Add Device Via EHome Steps 1. In the device list area, click Add to pop up the device adding dialog box. 2. Select the adding mode as EHome. 3. Enter the corresponding information of the device: Name, Device Account , and ISUP login key. 4. Click Add. 10.
Video Intercom Face Recognition Door Station User Manual You can add device, modify device, delete device, perform remote configuration, etc. in device management page. The specific method is similar to web configuration . For details, please refer to the iVMS-4200 client user manual. Note ● ● When adding a third-party door station encoding device, the client only supports the management of device information, and does not support direct preview.
Video Intercom Face Recognition Door Station User Manual 10.7.1 Add Person Steps 1. On the main page of the client, click Person Management to enter the person information configuration page. 2. Select an organization in the organization list and click Add on the person panel to pop up the adding person dialog. Note The Person No. will be generated automatically, and it is editable. 3. Set the person basic information. 1) Enter basic information: name, gender, tel, effective period and E-mail address.
Video Intercom Face Recognition Door Station User Manual 3) Click Start to Scan to add the fingerprint. 4) Click Add to save the fingerprint. Note Only some models of the devices support fingerprint function, please refer to the specific product. 6. Click Access Control and check the access control permissions that need to be configured. 7. Linked Device 1) Click Resident Information, and select the device to be bound. 2) Set the floor No. and room No. 8. Click Save to enable the settings. 10.7.
Video Intercom Face Recognition Door Station User Manual Note ● ● ● ● Click Download Template for Importing Person to download the template. The import template contains the following information: person name, gender, department code, certificate type, certificate number, phone number and address. The number of persons can not exceed 5000 in a single import. If the imported person No. already exists in the client database, the system will automatically replace the original person information.
Video Intercom Face Recognition Door Station User Manual 2. Click Settings to set issue card paramrters. - If you set issue card Mode as Local, you need to set Card Issuer, Card Type and Card No., and enable Buzzer and M1 Card Encryption and click OK to issue card. - If you set Issue Card Mode as Remote, select card issuing device, and click OK to issue card. 10.7.6 Permission Settings Add Permissions Steps 1. On the main page of the client, click Access Control → Access Group to enter the settings page.
Video Intercom Face Recognition Door Station User Manual You can call residents on the video intercom page, and the residents can also call the client software through the indoor station. The door station can also call the client software. Steps 1. On the main page, click Access Control → Video Intercom → Video Intercom to enter the video intercom page. 2. Select an organization from the list, and the residents list on the right displays the residents information under the organization. 3.
Video Intercom Face Recognition Door Station User Manual Note ● One video intercom device can only connect with one client software. ● The maximum ring duration can be set from 15 s to 60 s. ● The maximum speaking duration between the client software and indoor station can be set from 120 s to 600 s. 10.8.2 Search Video Intercom Information Search Call Logs Steps 1. On the Video Intercom page, click Access Control → Video Intercom → Call Log to enter the page. 2. Set the search conditions.
Video Intercom Face Recognition Door Station User Manual You can set the information type as all, advertising Information, property information, alarm information or notice information according to your needs. Time Set the start time and end time of a time period to search the logs. 3. Click Save. 4. Optional: You can reset the settings or export the notice after the search. Reset the Settings Click Reset to reset all the configured search conditions.
Video Intercom Face Recognition Door Station User Manual A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD27981B
