Face Recognition Door Station with 8-inch Screen User Manual
Face Recognition Door Station with 8-inch Screen User Manual Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Face Recognition Door Station with 8-inch Screen User Manual OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
Face Recognition Door Station with 8-inch Screen User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Face Recognition Door Station with 8-inch Screen User Manual Safety Instruction Warning • All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. • Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. • Please make sure that the power has been disconnected before you wire, install or dismantle the device.
Face Recognition Door Station with 8-inch Screen User Manual • Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or leakage of flammable liquid or gas. • Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. • Used batteries may result in pollution to the environment.
Face Recognition Door Station with 8-inch Screen User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Face Recognition Door Station with 8-inch Screen User Manual EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/ 65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Face Recognition Door Station with 8-inch Screen User Manual 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
Face Recognition Door Station with 8-inch Screen User Manual Contents 1 Appearance ................................................................................................ 1 1.1 Door Station ...................................................................................................... 1 1.2 Door Station with Keypad Module .................................................................... 2 1.3 Door Station with Fingerprint Module ...........................................................
Face Recognition Door Station with 8-inch Screen User Manual 3.4.3 Flush Mounting ....................................................................................... 22 4 Activation ................................................................................................. 24 4.1 Activate Device Locally .................................................................................... 24 4.2 Activate Device via Web ................................................................................
Face Recognition Door Station with 8-inch Screen User Manual 6.4 Device Management ....................................................................................... 33 6.5 Parameters Settings ........................................................................................ 33 6.5.1 Local Settings .......................................................................................... 34 6.5.2 System Configuration .............................................................................
Face Recognition Door Station with 8-inch Screen User Manual 7.6.1 Add Organization .................................................................................... 61 7.6.2 Modify and Delete Organization ............................................................. 61 7.7 Person Management ....................................................................................... 61 7.7.1 Add Person ............................................................................................. 62 7.7.
Face Recognition Door Station with 8-inch Screen User Manual 1 Appearance 1.1 Door Station Note Refers to the specific model for the appearance of the device. Figure 1-1 Door Station Table 1-1 Appearance Description No. Description No. Description 1 Wiring Terminal 7 TAMPER 2 Network Interface 8 Loudspeaker 3 IR Supplement Light 9 Debugging Port Note The debugging port is used for debugging only.
Face Recognition Door Station with 8-inch Screen User Manual No. Description No. Description 5 Camera 11 SD Card Slot 6 CMOS 1.2 Door Station with Keypad Module Note Refers to the specific model for the appearance of the device. Figure 1-2 Door Station with Keypad Module Table 1-2 Appearance Description No. Description No.
Face Recognition Door Station with 8-inch Screen User Manual No. Description No. Description 4 Microphone 10 Debugging Port Note The debugging port is used for debugging only. 5 Camera 11 MicroUSB Interface 6 CMOS 12 SD Card Slot 1.3 Door Station with Fingerprint Module Note Refers to the specific model for the appearance of the device.
Face Recognition Door Station with 8-inch Screen User Manual Table 1-3 Appearance Description No. Description No. Description 1 Wiring Terminal 8 Fingerprint Module 2 Network Interface 9 TAMPER 3 IR Supplement Light 10 Loudspeaker 4 Microphone 11 Debugging Port Note The debugging port is used for debugging only. 5 Camera 12 MicroUSB Interface 6 CMOS 13 SD Card Slot 7 Button 1.4 Door Station with 4G Module Note Refers to the specific model for the appearance of the device.
Face Recognition Door Station with 8-inch Screen User Manual Figure 1-4 Door Station with 4G Module Table 1-4 Appearance Description No. Description No. Description 1 Wiring Terminal 7 TAMPER 2 Network Interface 8 Loudspeaker 3 IR Supplement Light 9 Debugging Port Note The debugging port is used for debugging only.
Face Recognition Door Station with 8-inch Screen User Manual 2 Terminal and Wiring Description Door station can be wired to alarm input interface, alarm input interface, door lock, door contact and so on.
Face Recognition Door Station with 8-inch Screen User Manual 3 Installation 3.1 Install Door Station Note • Gang box is required for the installation of door station. • The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. • Complete wiring during installation. Refers toTerminal and Wiring Description for wiring details. • Make sure all the related equipment is power-off during the installation.
Face Recognition Door Station with 8-inch Screen User Manual Mounting Plate Figure 3-1 Mounting Plate Note The dimension of the mounting plate is 233 mm (W) × 112.4 mm (H) × 21 mm (D).
Face Recognition Door Station with 8-inch Screen User Manual Gang Box Figure 3-2 Gang Box Note • The dimension of the gang box is 236.9 mm (W) × 128.4 mm (H) × 40.8 mm (D). • The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 237.5 mm (W) × 128.9 mm (H) × 41.3 mm (D). 3.1.2 Surface Mounting Steps 1. Paste the mounting template on the wall according to the installation location requirements.
Face Recognition Door Station with 8-inch Screen User Manual Note • Do not touch the SD card slot and other devices during the process of plugging in and unplugging the power interface. • Apply Silicone sealant among the joints between the device and the wall (except the lower side) to keep the raindrop from entering. Figure 3-3 Surface Mounting 3.1.3 Flush Mounting Steps 1. Cave an installation hole in the wall. The suggested dimension of the installation hole is 237.5 mm (W) × 128.9 mm (H) × 41.
Face Recognition Door Station with 8-inch Screen User Manual Figure 3-4 Flush Mounting 3.2 Install Door Station with Keypad Module Note • Gang box is required for the installation of door station. • The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station. • Complete wiring during installation. Refers to Terminal and Wiring Description for wiring details. • Make sure all the related equipment is power-off during the installation.
Face Recognition Door Station with 8-inch Screen User Manual Mounting Plate Figure 3-5 Mounting Plate Note The dimension of the mounting plate is 233 mm (W) × 112.4 mm (H) × 21 mm (D).
Face Recognition Door Station with 8-inch Screen User Manual Gang Box Figure 3-6 Gang Box Note • The dimension of the gang box is 312.9 mm (W) × 128.4 mm (H) × 40.8 mm (D). • The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 313.5 mm (W) × 128.9 mm (H) × 41.3 mm (D). 3.2.
Face Recognition Door Station with 8-inch Screen User Manual Steps 1. Loosen splice set screws, and separate the host from the keypad module. Paste the mounting template on the wall according to the installation location requirements. Drill holes according to the location of the screw holes of the drill template, and install the expansion bolts into the screw holes. 2. Fix the mounting plate to the wall with 4 supplied screws. 3. Fix the device to the mounting plate, and fix the device with the set screws.
Face Recognition Door Station with 8-inch Screen User Manual 2. Take out the gang box. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. Fix the gang box with 4 expansion bolts. 3. Insert the door station into the gang box, and fix it with set screws. Note Do not touch the SD card slot and other devices during the process of plugging in and unplugging the power interface. Figure 3-8 Flush Mounting 3.
Face Recognition Door Station with 8-inch Screen User Manual Mounting Plate Figure 3-9 Mounting Plate Note The dimension of the mounting plate is 233 mm (W) × 112.4 mm (H) × 21 mm (D).
Face Recognition Door Station with 8-inch Screen User Manual Gang Box Figure 3-10 Gang Box Note • The dimension of the gang box is 312.9 mm (W) × 128.4 mm (H) × 40.8 mm (D). • The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 313.5 mm (W) × 128.9 mm (H) × 41.3 mm (D). 3.3.
Face Recognition Door Station with 8-inch Screen User Manual Steps 1. Loosen splice set screws, and separate the host from the fingerprint module. Paste the mounting template on the wall according to the installation location requirements. Drill holes according to the location of the screw holes of the mounting template, and install the expansion bolts into the screw holes. 2. Fix the mounting plate to the wall with 4 supplied screws. 3.
Face Recognition Door Station with 8-inch Screen User Manual the wall, insert the gang box into the installation hole, and mark the gang box screw holes’ position with a marker. 2. Take out the gang box. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. Fix the gang box with 4 expansion bolts. 3. Insert the door station into the gang box, and fix it with set screws.
Face Recognition Door Station with 8-inch Screen User Manual • Make sure all the related equipment is power-off during the installation. • Installation Location: the lens of the device shall be 1.5 meters away from the ground. 3.4.1 Door Station with 4G Module Installation Accessories Mounting Plate Figure 3-13 Mounting Plate Note The dimension of the mounting plate is 233 mm (W) × 112.4 mm (H) × 21 mm (D).
Face Recognition Door Station with 8-inch Screen User Manual Gang Box Figure 3-14 Gang Box Note • The dimension of the gang box is 312.9 mm (W) × 128.4 mm (H) × 40.8 mm (D). • The installation hole should be bigger than the actual size. The suggested dimension of the installation hole is 313.5 mm (W) × 128.9 mm (H) × 41.3 mm (D). 3.4.
Face Recognition Door Station with 8-inch Screen User Manual Steps 1. Loosen splice set screws, and separate the host from the 4G module. Paste the drill template on the wall according to the installation location requirements. Drill holes according to the location of the screw holes of the drill template, and install the expansion bolts into the screw holes. 2. Fix the mounting plate to the wall with 4 supplied screws. 3. Fix the device to the mounting plate, and fix the device with the set screws. 4.
Face Recognition Door Station with 8-inch Screen User Manual the wall, insert the gang box into the installation hole, and mark the gang box screw holes’ position with a marker. 2. Take out the gang box. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into the screw holes. Fix the gang box with 4 expansion bolts. 3. Insert the door station into the gang box, and fix it with set screws.
Face Recognition Door Station with 8-inch Screen User Manual 4 Activation You can activate the device via Guarding Vision or Batch Configuration Tool. Default parameters of door station are as follows: • Default IP Address: 192.0.0.65. • Default Port No.: 8000. • Default User Name: admin. 4.1 Activate Device Locally You are required to activate the device first by settings a strong password for it before you can use the device. Steps 1. Power on the device to enter the activation page automatically.
Face Recognition Door Station with 8-inch Screen User Manual Network → TCP/IP to edit the door station IP address, subnet mask, gateway and other parameters. 4.3 Activate Device via Client Software Steps 1. On the device management page, select Encoding Device/Door Station, and select the device to be activated in the online device area. 2. Click Activate to enter the activation page. 3. Create a password, and confirm the password. Click OK to activate the device.
Face Recognition Door Station with 8-inch Screen User Manual 5 Door Station Local Operation 5.1 Door Station Local Configuration Hold the menu page, enter the password and tap OK to enter the configuration page. 5.1.1 Edit Network Parameters After activating, you should edit the network parameters. Set the IP address of the door station and the IP address of the door station associated device, to realize the network communication between the devices. Steps 1.
Face Recognition Door Station with 8-inch Screen User Manual Note After the channel mode is enabled, the residents can directly pass through without verification. 6. After the door station settings are completed, exit the settings page to complete the configuration. Note • Main Door Station: the serial No. is 0. Sub Door Station: the serial number is greater than 0 (Serial number of sub door station ranges from 1 to 8). • One unit is equipped with at least one main door station.
Face Recognition Door Station with 8-inch Screen User Manual 3) Tap OK to enable the settings. 6. Add Face. 1) Select Face, and point the face at the camera. 2) Tap to add the face. 3) Tap to enable the settings. 7. Add Fingerprint. 1) Select Fingerprint, and tap +. 2) Put your finger on the fingerprint reader and add the fingerprint. 8. Set User Permission as User or Administrator. 9. Exit the settings page. 5.1.4 Search Version You can view the device system version and QR Code of the device.
Face Recognition Door Station with 8-inch Screen User Manual Note • Both the main and sub door station support the elevator control function, that is, after calling the residents successfully, tap the unlock button on the indoor station, the elevator will automatically arrive at the floor where the door station is located, and the permission of the floor where the household is located will be opened (The elevator calling will take effect only after the elevator control is configured and the corresponding c
Face Recognition Door Station with 8-inch Screen User Manual 5.3 Unlock Door You can unlock door station in following methods: Unlock by password, unlock by presenting card, unlock by face, and unlock by fingerprint. 5.3.1 Unlock by Password Unlock by Password On the menu page, Tap to enter the calling page. Enter【 # + Password + unlock button】to unlock door. Unlock by Public Password Note Make sure you have created the public password via iVMS-4200 Client Software remotely.
Face Recognition Door Station with 8-inch Screen User Manual 5.3.4 Unlock by QR Code Door station supports unlock by QR code. You can generate a QR code through the mobile phone client, and use the door station camera to scan the mobile phone QR code to open the door. Steps Note • Make sure that the door station IP has been added to the indoor station, and the indoor station and the door station can communicate normally. • Make sure that the door station is connected to the network.
Face Recognition Door Station with 8-inch Screen User Manual 6 Remote Configuration via Web 6.1 Live View In the browser address bar, enter the IP address of the device, and press the Enter key to enter the login page. Enter the user name and password, and click Login to enter the Live View page. • You can start/stop live view, capture, record, audio on/off, two-way audio, etc. • The stream type can be set as main stream or sub-stream.
Face Recognition Door Station with 8-inch Screen User Manual 6.4 Device Management You can manage the linked device on the page. Add Linked Device Click Add to add the indoor station or sub door station. Enter the parameters and click OK to add the device. Click Import. Enter the information of the device in the template to import devices in batch. Caution When importing device information in batches, the original data will be cleared automatically.
Face Recognition Door Station with 8-inch Screen User Manual Note Run the IE browser, and click Protected Mode. → Internet Options → Security to disable the Click Settings to enter the settings page. 6.5.1 Local Settings Video Parameters: • Stream Type: Select the stream type toMain StreamorSub Stream. • Play Performance: selectShortest Delay,BalanceorGood Fluencyaccording to your needs.
Face Recognition Door Station with 8-inch Screen User Manual 6.5.2 System Configuration In system configuration, you can view device information, set system time, configure maintenance settings, and configure user information, etc. Click System to enter the settings page. Basic Information Click System Settings → Basic Information to enter the settings page. Device system information includes device name, device No., device language, device system type, device model, serial No.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-2 System Maintenance • Reboot:Click Reboot to reboot the device. • Restore: Click Restore to restore parameters to default settings. Restore Reset all the parameters, except IP address, subnet mask and default gateway, to the default settings. Default Restore all parameters to default settings. • Export Parameters: Export device parameter files, which can be used to configure the same parameters for another device. 1.
Face Recognition Door Station with 8-inch Screen User Manual Note Do not power off during the upgrading. The device will reboot automatically after upgrading. Security Service SSH is generally used for remote debugging. For device security, it is recommended not to enable SSH when the service is not needed. Click Security → Security Service to enter the settings page. Slide to enable Save to enable the settings. User Management Click User Management to enter the settings page.
Face Recognition Door Station with 8-inch Screen User Manual characters, lowercase letters and uppercase letters, it is a medium password. If the password is a combination of numbers and lowercase letters, or a combination of numbers and uppercase letters, it is a weak password. Online User Click User Management → Online Users to enter the settings page. The user can view all user information logged in to the device, including the No., logged-in user name, user type, IP address, and user operating time.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-3 TCP/IP Settings 2. Configure the network parameters. - Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Default Gateway, Preferred DNS Server and Alternate Server. - Check DHCP, the device will get the parameters automatically. 3. Configure Alarm Center IP and Alarm Host Port. 4. Click Save to enable the settings. Port Settings Port setting parameters consist of HTTP Port, RTSP Port, HTTPS Port and Server Port.
Face Recognition Door Station with 8-inch Screen User Manual Steps 1. Click Settings → Network → Basic Settings → Port to enter the settings page. 2. The port No. needs to be changed when there are port conflicts. HTTP Port Figure 6-4 Port Configuration When you log in with a browser, you need to add the modified port number after the address. For example, when the HTTP port number is changed to 81, you need to enter http://192.0.0.65:81 when you log in with a browser.
Face Recognition Door Station with 8-inch Screen User Manual terminals on the same network segment. After successfully registering with the SIP server, the terminals can dial the SIP ID to complete the call. Steps 1. Click Network → Basic Settings → SIP to enter the settings page. Figure 6-5 SIP Settings 2. Check Enable VOIP Gateway. 3. Enter User Name and Password. 4. Set SIP Server Address and Server Port. 5. Enter dialing Number and Display the User Name. 6. Click Save to enable the settings.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-6 FTP Settings 2. Check Enable FTP, and select Server Type, enter Server IP Address, Port, User Name and Password. 3. Optional: Check Enable Anonymous, you do not need to configure the user name and password. 4. You can save the configuration file in Root Directory, Parent Directory or Child Directory. • You can set device name, device IP, time, building No. and unit No. in parent directory. • You can set building No., unit No.
Face Recognition Door Station with 8-inch Screen User Manual Platform Access Settings Platform access provides you an option to manage the devices via platform. Steps 1. Click Configuration → Network → Advanced Settings → Platform Access to enter the settings page. 2. Select platform access mode. 3. Check Enable, configure the server IP address and set Access Server IP Address and Verification Code. 4. Click Save to enable the settings.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-7 Video Parameters 2. Configure the video parameters. Stream Type Set the video parameters of main stream and sub-stream. Video Type Select the stream type as video stream, or video & audio composite stream. The video & audio composite stream includes audio signal and video signal. Resolution You can select the main stream resolution as 1280*720P or 1920*1080P, and select the sub-stream resolution as 640*480P or 1280*720P.
Face Recognition Door Station with 8-inch Screen User Manual The device supports H.264. Please refer to the specific model for the video encoding type. I Frame Interval The number of frames between two key frames before and after. You can set I Frame Interval from 1 to 400. 3. Click Save to enable the settings. Audio Parameters Click Configuration → Video/Audio → Audio to enter the settings page. Figure 6-8 Audio Parameters You can set the stream type and audio encoding of the device audio.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-9 Display Settings 2. Select the Format. 3. Optional: Enable WDR. 4. Set the display parameters. - Adjust the brightness, contrast, saturation, and sharpness of the preview screen by dragging the progress bar. - Adjust the screen by entering the corresponding value in the input box. Note • If the current settings do not meet expectations, you can click Restore Defaults to restore the parameters to the initial status.
Face Recognition Door Station with 8-inch Screen User Manual 3) Adjust Supplement Light Brightness by dragging the progress bar. 4) Set the Daytime Start Time and Daytime End Time. 7. Exit the settings page. 6.5.6 Event Settings When an event occurs, an alarm linkage will be triggered. Motion Detection Settings Motion detection detects the moving objects in the configured surveillance area, and a series of actions can be taken when the alarm is triggered. Steps 1.
Face Recognition Door Station with 8-inch Screen User Manual 2. Slide Enable Motion Detection to enable the function. Note If the motion detection function is disabled, you cannot draw the detection area and adjust the sensitivity. 3. Click Draw Area. Click and drag the mouse on the window to draw a motion detection area. Click Stop Drawing to finish the drawing. Clear Area Click Clear All to clear all of the areas. Adjust Sensitivity Move the slider to set the sensitivity of the detection.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-11 Event Linkage 2. Configure the major types of events, the major types of access control events are divided into Device Event and Door Event. 3. Configure minor types of events. - When the major type of access control event is selected as Device Event, the minor type is Host Tamper Alarm. - When the major type of access control event is selected as Door Event, the minor type is Door Open Timeout. 4.
Face Recognition Door Station with 8-inch Screen User Manual 6.5.7 Two-way Audio Configuration Device No. Settings Identify the organization the device belongs to and the device No. Steps 1. Click Settings → Intercom → Device No. to enter the settings page. Figure 6-12 Device No. Settings 2. Select Device Type as door station or outer door station. 3. Set Phase No., Building No., Unit No., Floor No., No. and Community No. of the device. 4. Click Save to enable the settings.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-13 Session Settings 2. Set activation password, main station IP, intercom serve and enable 1.0 protocol. Register Number Register Number of the device, created by default. Registration Password Activation password of the main station. Main Station IP IP address of the main station. Video Intercom Server IP Server IP of the video intercom server. Enable Protocol 1.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-14 Time Parameter You can drag the slider to configure Max. Call Duration and Max. Message Duration, and click Save to enable the settings. Note • The Max. call duration ranges from 90 s to 120 s. • The Max. message duration ranges from 30 s to 60 s. 6.5.8 Access Control Settings Permission Password In order to improve password security, it is recommended to modify the permission password regularly. Steps 1.
Face Recognition Door Station with 8-inch Screen User Manual Caution In order to prevent security risks, you must modify the initial password in time after the initial login to prevent others from logging in to your device without authorization or causing other undesirable consequences. 4. Click Save to enable the settings. Set Door Parameters Steps 1. ClickSettings → Access Control → Door Parametersto enter the settings page. 2. Select theDoor, and edit theDoor Name. 3. SetRelay ReverseandOpen Duration.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-16 Elevator Control 2. Check Enable Elevator Control. 3. Select an Elevator No., Elevator Controller Type and Interface Type. Note • Only main door station supports elevator control. • If you select Network Interface, enter the elevator controller's IP address, port No., user name, and password. • You can connect the door station to the elevator controller with RS-485 wire. • Opening Time: Ranges from 1 second to 255 seconds. 4.
Face Recognition Door Station with 8-inch Screen User Manual Note No. 1 can be set to work mode as ladder control, card reader or disabled. 4. Click Save to enable the settings. 6.5.9 Smart Settings Biometrics Settings Steps 1. Click Configuration → Smart → Biometrics Settings to enter the settings page. Figure 6-18 Biometrics Settings 2. Slide to enable Face Anti-spoofing, and set Live Face Detection Security Level. 3. Select Application Mode as Indoor or Other. 4.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-19 Area Configuration 2. Drag the frame to adjust the size of the recognition area. 3. Click Save. 4. Optional: Click or in Live View to record or capture. 6.5.10 Theme Settings Set the advertisement on the main page of the device. Steps 1. Click Configuration → Theme to enter the settings page.
Face Recognition Door Station with 8-inch Screen User Manual Figure 6-20 Theme Settings 2. Set the advertisement theme. 1) Click + Add Theme. 2) Create a theme name, and select the advertisement body as picture or Video. 3) Click Save. 3. Click + to select a picture from the local as the material to be played in standby, and click upload. 4. Set the play schedule. 1) Select a theme and drag the time interval to be played on the timeline. 2) Optional: Click the drawn area to edit the time manually.
Face Recognition Door Station with 8-inch Screen User Manual 7 Remote Configuration via Client Software You can set Video Intercom system and manage video intercom products including indoor station, door station and main station via Guarding Vision client software. 7.1 Edit Device Network Parameters Before You Start Before configuring the device remotely, make sure that the device is activated. Steps 1. On the person management page, click Online Device. 2.
Face Recognition Door Station with 8-inch Screen User Manual 4. Enter the device Name, User Name, Password, and click Add. Note • Only when the doorphone is added to the client software, you can remotely configure the indoor station. • Only online devices with the same user name and activation password can support batch activation. After the device is added, the device information will be listed in the device list area. 7.2.2 Add Device via IP Address Steps 1.
Face Recognition Door Station with 8-inch Screen User Manual 4. Select the file and click Add to import. Note The file format for batch import is .csv format. 7.2.5 Add Device Via EHome Steps 1. In the device list area, click Add to pop up the device adding dialog box. 2. Select the adding mode as EHome. 3. Enter the corresponding information of the device: Name, Device Account , and ISUP login key. 4. Click Add. 7.
Face Recognition Door Station with 8-inch Screen User Manual You can add device, modify device, delete device, perform remote configuration, etc. in device management page. The specific method is similar to web configuration . For details, please refer to the Guarding Vision client user manual. Note • When adding a third-party door station encoding device, the client only supports the management of device information, and does not support direct preview.
Face Recognition Door Station with 8-inch Screen User Manual You can add, edit, import, and export person information. 7.7.1 Add Person Steps 1. On the main page of the client, click Person Management to enter the person information configuration page. 2. Select an organization in the organization list and click Add on the person panel to pop up the adding person dialog. Note The Person No. will be generated automatically, and it is editable. 3. Set the person basic information.
Face Recognition Door Station with 8-inch Screen User Manual 1) Click Credential → Fingerprint. 2) Select Collection Mode and Collection Recorder. 3) Click Start to Scan to add the fingerprint. 4) Click Add to save the fingerprint. Note Only some models of the devices support fingerprint function, please refer to the specific product. 6. Click Access Control and check the access control permissions that need to be configured. 7. Linked Device 1) Click Resident Information, and select the device to be bound.
Face Recognition Door Station with 8-inch Screen User Manual 4. Click Close to complete the import. Note • Click Download Template for Importing Person to download the template. • The import template contains the following information: person name, gender, department code, certificate type, certificate number, phone number and address. • The number of persons can not exceed 5000 in a single import. • If the imported person No.
Face Recognition Door Station with 8-inch Screen User Manual Steps 1. On the person management page, click Batch Issue Cards. 2. Click Settings to set issue card paramrters. - If you set issue card Mode as Local, you need to set Card Issuer, Card Type and Card No., and enable Buzzer and M1 Card Encryption and click OK to issue card. - If you set Issue Card Mode as Remote, select card issuing device, and click OK to issue card. 7.7.6 Permission Settings Add Permissions Steps 1.
Face Recognition Door Station with 8-inch Screen User Manual 7.8.1 Video Intercom You can call residents on the video intercom page, and the residents can also call the client software through the indoor station. The door station can also call the client software. Steps 1. On the main page, click Access Control → Video Intercom → Video Intercom to enter the video intercom page. 2.
Face Recognition Door Station with 8-inch Screen User Manual Note • One video intercom device can only connect with one client software. • The maximum ring duration can be set from 15 s to 60 s. • The maximum speaking duration between the client software and indoor station can be set from 120 s to 600 s. 7.8.2 Search Video Intercom Information Search Call Logs Steps 1. On the Video Intercom page, click Access Control → Video Intercom → Call Log to enter the page. 2. Set the search conditions.
Face Recognition Door Station with 8-inch Screen User Manual Information Type You can set the information type as all, advertising Information, property information, alarm information or notice information according to your needs. Time Set the start time and end time of a time period to search the logs. 3. Click Save. 4. Optional: You can reset the settings or export the notice after the search. Reset the Settings Click Reset to reset all the configured search conditions.
Face Recognition Door Station with 8-inch Screen User Manual 3. Optional: Click Arm All or Disarm All to arm or disarm devices.
Face Recognition Door Station with 8-inch Screen User Manual 8 Batch Configuration Tool You can only configure and operate the door station after creating a password for the device activation. Default parameters of door station are as follows: • Default IP Address: 192.0.0.65. • Default Port No.: 8000. • Default User Name: admin. 8.1 Create the Organization Structure In the batch configuration tool settings page, click Flash Rom to enter the settings page.
Face Recognition Door Station with 8-inch Screen User Manual Link Main Door Station Steps 1. Select the community structure. Here takes building 1 (with 1 unit, 1 floor, 2 rooms) as an example. Figure 8-1 Link Main Door Station 2. Set the starting IP address of main door station (The default starting IP is paired with the unit 1 sub door station). 3. Click Calculate to get the end IP address of door station and main door station No.(such as 1-1-1-1).
Face Recognition Door Station with 8-inch Screen User Manual Caution • During the rooting process, if the door station has been activated locally on the device or the configuration tool, the login password entered here is the activation password. • During the rooting process, if the door station is not activated, then entering the login password here is to set a password by yourself. At the same time as the rooting, the door station will be activated. Link Sub Door Station Steps 1.
Face Recognition Door Station with 8-inch Screen User Manual 4. Set the corresponding network information. Set the main door station IP address, SIP server IP address, main station IP address, central platform IP address and port No. Set the subnet mask and gateway address. 5. In the online device area, select a door station, enter the login password, and click Root. At this time, the corresponding No. (such as 1-1-1-1) and IP address of the sub door station are generated.
Face Recognition Door Station with 8-inch Screen User Manual You can add online devices to be upgraded in the same network segment, or add devices to be upgraded by IP address or IP segment. Add Online Device for Upgrading Steps 1. On the batch upgrade page, click Online Devices to open the online device window. 2. Select a device, click Login Device, enter the user name and password, and click OK. Figure 8-4 Add Online Device 3.
Face Recognition Door Station with 8-inch Screen User Manual 2. Search and add devices. Search via IP Enter the device IP address and search for the device to be added. Search via IP Segment Enter the device IP segment and search for the device to be added. 3. Click Add Device. 8.2.2 Upgrade Device You can upgrade the device via the file, or upgrade the device online. Online Upgrade The client can search for the new upgrade file information of the device automatically on the server.
Face Recognition Door Station with 8-inch Screen User Manual Figure 8-5 Upgrade by File 2. Select the upgrade file, click Open and Start to Upgrade, and the device starts to upgrade. Note Device will reboot automatically after upgrading.
UD23399N