User Manual of DS-3WF01C-2N DS-3WF01C-2N User Manual
User Manual of DS-3WF01C-2N User Manual COPYRIGHT ©2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
User Manual of DS-3WF01C-2N Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User Manual of DS-3WF01C-2N Table of Contents Chapter 1 Product Overview .................................................................................. 5 1.1 1.2 1.3 1.4 1.5 1.6 Product Advantages ......................................................................................................5 Electrical Specifications ...............................................................................................6 Features..........................................................................
User Manual of DS-3WF01C-2N Chapter 1 Product Overview 1.1 Product Advantages DS-3WF01C-2N is specially designed for elevator wireless video transmission and customized products; compared with the traditional elevator video transmission products, it has the following advantages: 1. Good anti - jamming ability Super low frequency power supply interference, electrical spark interference, inverter motor interference, control signal interference etc.
User Manual of DS-3WF01C-2N Note: Please confirm whether those non-standard channels are permitted locally before using them. 1.2 Electrical Specifications DS-3WF01C-2N electrical specifications as shown below: Table 1-1 Electrical Specifications Wireless Hardware Software Items Specifications Standard IEEE802.11 b/g/n（2T2R 300Mbps） Operation Frequency 802.
User Manual of DS-3WF01C-2N Auto ACK timing Adjust Supported Management and Logs NTP, SNMP, Syslog, Telnet, AC Web based Configuration Supported Firmware Update Supported Bandwidth supported 20M/40MHz 1.3 Features • High performance 802.
User Manual of DS-3WF01C 3WF01C-2N environments 1.4 Using Example DS-3WF01C-2N 2N products can be used ins inside ide the elevator shaft to survey the video transmission, while the use of multiple network interfaces equipped with elevator advertising machine to real-time real time updates. Backhaul data networks can rely on existing properties or assembling outdoor wireless device. dev Figure 1-1 DS-3WF01C-2N Using Example 1.
User Manual of DS-3WF01C-2N Memory 64MB DRAM, 8MB Flash Physical Interface 3×10/100M Base-TX (Cat. 5/5E, RJ-45) Ports LED LAN, WLAN, 3×Link Quality Power Supply POE+, Power Adapter 12V 1.6 LED Description DS-3WF01C-2N use LED to reflect the current status of working and quality of the connection. LED is mainly divided into two parts, status of the device and the quality of the connection.
User Manual of DS-3WF01C-2N and is sending the wireless data.
User Manual of DS-3WF01C-2N Red The light indicates the signal level Yellow Green, yellow and red lights on, indicates Green Signal Level the wireless signal level is high Yellow and red lights on, indicating signal level is medium Only red light on, indicating that the signal is weak or no signal Chapter 2 Installation 2.1 Connections and installation The installation of DS-3WF01C-2N as shown in the following figure: Figure 2-1 Connections 1.
User Manual of DS-3WF01C-2N 2. POE power adaptor 3. Mount Bracket 4. Three LAN port on the device can be connected to the camera There are two devices within a package: DS-3WF01C-2N (T) and DS-3WF01C-2N (R), two POE power adaptors. The DS-3WF01C-2N (T) should be mounted on top of the elevator car; it’s normally linked up with network cameras and other network advertising screens equipment through the network cable.
User Manual of DS-3WF01C-2N parameters of the default factory settings as shown below. If you want to change the default values and other parameters, please read the manual in the following sections. Table 2-1 Main parameters at the factory settings Items Wireless Elevator Car / DS-3WF01C- Elevator Room / DS-3WF01C- 2N(T) 2N(R) Access Point Client IP address 192.168.1.35 192.168.1.
User Manual of DS-3WF01C-2N 1. Right click Local Area Connection icon of your computer and click properties, then click Continue, the Local Area Connection Properties dialog box appears as shown below: Figure 3-1 Local Area Connection Properties 2.
User Manual of DS-3WF01C-2N Figure 3-2 IP Settings 3. As shown in the figure above, IP address should be set to 192.168.1.*, but cannot be the same as DS-3WF01C-2N, here * can be a number between 1-255 (but not 36 or 35) since the DS-3WF01C-2N (T) default IP address is 192.168.1.35, and the DS3WF01C-2N(R) default IP address is 192.168.1.36. 4. Input the default IP 192.168.1.36 or 192.168.1.35 into the address bar of your web browser, click Enter. 5.
User Manual of DS-3WF01C-2N Figure 3-3 DS-3WF01C-2N Login Page 3.2 Wizard Users can quickly configure DS-3WF01C-2N according to the following steps through the wizard in this chapter. 1. The first page shown after log in is the Status page, which indicates the working status, current setting, software version and other information of the DS-3WF01C2N device. User can switch to other pages by clicking the main menus.
User Manual of DS-3WF01C-2N Figure 3-4 Status– DS-3WF01C-2N (T) 2. Click Wizard. The page goes to Wizard page as shown below, and this page helps to set the basic network parameters. The default mode is Bridge mode, and the default LAN IP address of DS-3WF01C-2N (T) is 192.168.1.35, the default LAN IP address of DS-3WF01C-2N(R) is 192.168.1.36. If the user wants to configure the device to Router mode, please refer to chapter 7.
User Manual of DS-3WF01C-2N Figure 3-5Wizard – DS-3WF01C-2N (T) Elevator Car: (AP mode), in this scenario mode, DS-3WF01C-2N will be set to AP mode; it can be connected to a client device. When you close the TDMA function, your phone or laptop can connect to the DS-3WF01C-2N. If you need other wireless configurations in detail, please refer to chapter 7.
User Manual of DS-3WF01C-2N 3、Click Save & Apply button, the device will reboot and apply your configuration. Figure 3-7 Complete wizard settings Chapter 4 Status The status page is the first page after logging in, the page displays the current configuration and working status of the device.
User Manual of DS-3WF01C-2N 20
User Manual of DS-3WF01C-2N Figure 4-1 Status Overview: Status->Overview, This page shows the current configuration information of the system, including the system, memory, network, DHCP leases, wireless, associated stations, active UPnP redirects. Firewall: Status - > firewall, showing the device's current IPv4 and IPv6 firewall; please do not click on the "Reset Counters" and "Restart Firewall" without the guidance of network manager, so as to avoid unnecessary trouble.
User Manual of DS-3WF01C-2N General Settings: some basic information is supported to configure on this page, including time, log, language and interface style. Click on the "general settings" page, click on "Sync with browser" to synchronize the local time to the device, and it will be displayed in the status page too. The time synchronization can help network administrator check equipment operation status and log information conveniently, and can also help tracking running status of the device.
User Manual of DS-3WF01C-2N Figure 5-2 System Properties - Logging Language and Style: choose the language of the web page you want. You can modify the Language into English or Chinese. The default Design is bootstrap style, you can also choose openwrt style based on personal hobby. Figure 5-3 System Properties – Language and Style Time Synchronization: when the device can surf the Internet, you can enable the NTP client and fill in the NTP server candidates.
User Manual of DS-3WF01C-2N Figure 5-4 System Properties – Time Synchronization 5.2 Administration Router Password: Changes the administrator password for accessing the device. Figure 5-5 Password SSH Access: Drop bear offers SSH2 network shell access and an integrated SCP server. Here you can change the default SSH parameters.
User Manual of DS-3WF01C-2N Figure 5-6 SSH Note: after saving the configuration of administration page, the device will automatically close telnet access, the user can login the device through more secure SSH. System->Software, Startup and Scheduled Tasks pages: it is not recommended to operating, just keep the default configuration. 5.
User Manual of DS-3WF01C-2N Figure 5-7 LED Settings The red LED intensity value is the smallest of the 3 LEDs (red < yellow < green), the default range of red LED: -95~-1dBm, yellow: -71~-1dBm, green: -56~-1dBm. When the signal strength is higher than -95dB and below -71dBm, red light; when the signal strength is higher than -71dB and below -56dBm, both red and yellow light; when the signal strength is higher than -56dBm, all the 3 LEDs light. 5.
User Manual of DS-3WF01C-2N Figure 5-8 Backup / Restore Flash new firmware image Upload a sysupgrade - compatible image here to replace the running firmware. Check "Keep settings" to retain the current configuration (requires an OpenWrt compatible firmware image). Figure 5-9 Flash new firmware image 5.5 Reboot Click Perform reboot to reboot the operating system of your device.
User Manual of DS-3WF01C-2N Chapter 6 Services Services page is divided into dynamic DNS, SNMP, CAPWAP, WiFiDog and UPNP, the following lists only CAPWAP and SNMP instructions. 6.1 CAPWAP CAPWAP: Control and Provisioning of Wireless Access Points Protocol Specification. CAPWAP settings page as shown in figure. Enable this feature; you need to use the AC management system.
User Manual of DS-3WF01C-2N Note: If you want to set a client mode device to join AC successfully, the client should be connected to the access point device first, and the access point device has also opened the CAPWAP function and joined the same AC system. Figure 6-2 CAPWAP Settings 6.2 SNMP SNMP: When SNMP is enabled, you can check the working condition and information of the device by a SNMP tool.
User Manual of DS-3WF01C-2N Figure 6-3 SNMP You can configure the SNMP parameters in Basic Settings part. Check SNMP Enable and fill in Location, Mail, Group; then you can manage the device through a SNMP tool in your computer.
User Manual of DS-3WF01C-2N Figure 6-4 Basic Settings The device supports a higher level of SNMP protocol; you can choose to enable SNMPv3, with the corresponding SNMP management tools to use.
User Manual of DS-3WF01C-2N Figure 6-5 SNMPv3 Settings The device also supports trigger trap information; you can choose to enable Trap, fill in the trap server IP, then you will receive Trap information through the SNMP management tool in your computer.
User Manual of DS-3WF01C-2N Chapter 7 Network The network settings page is divided into the Interface, Wifi, DHCP and DNS, Hostnames, Static Routes, Diagnostics, Firewall, VLAN, Ping Watchdog, QoS. We will focus on the Interface, wireless, network diagnostics, firewall, Ping, Watchdog. VLAN. The following will focus on the introduction of the Interface, Wifi, Diagnostics, Firewall, VLAN, Ping Watchdog. 7.1 Interfaces 7.1.
User Manual of DS-3WF01C-2N Figure 7-2 General Setup Protocol: the interface access IP address options, it divided into static address, DHCP client (to obtain the IP dynamically) and a variety of other ways. If you set a static IP, you need to set the IP, subnet mask, etc.; when set to DHCP client, the device can obtain IP from DHCP server automatically.
User Manual of DS-3WF01C-2N IPv4 address: IP address of this interface, you can configure it according to your own needs, but to ensure that IP cannot be the same as other devices in the same network, so as not to cause IP address conflict. IPv4 netmask: the subnet mask of this interface, you can set it according to your own needs. Use custom DNS server: It should be set to the value of the local DNS server.
User Manual of DS-3WF01C-2N Click to enter the firewall settings page. Choose the firewall zone you want to assign to this interface. Select unspecified to remove the interface from the associated zone or fill out the create field to define a new zone and attach the interface to it. please refer to the Manual Section 7.3 firewall. Figure 7-4 Firewall Settings 7.1.2 DHCP Server Drop down the interface page; you can see the basic settings of the DHCP server.
User Manual of DS-3WF01C-2N Figure 7-5 DHCP Server DHCP: Assign IP address to client device, such as phones, laptops etc. A device should enable DHCP client mode to get IP automatically. 7.1.3 Add New Interface Click on the “Add new interface” button to add a new interface.
User Manual of DS-3WF01C-2N Fill in the name of the new interface, such as LAN2, select the Ethernet adapter eth1 interface, all of the configuration in this page can be modified again in the subsequent pages. Figure 7-7 Create Interface Click Submit, will enter the new LAN2 interface configuration page. This page can be configured for all the existing interfaces, as shown below; you can still see the original LAN interface.
User Manual of DS-3WF01C-2N Figure 7-8 Create LAN2 interface Please refer to chapter 7.1.1 to see how to configure the interface. 7.1.4 Router Mode Routing mode DS-3WF01C-2N is equivalent to a router, it has a WAN port and LAN port. You should select an interface which needs to be removed from the default LAN interface for the WAN interface configuration. Below we will set eth1 port to WAN as an example, introduces the configuration of the WAN. Please refer to the manual 7.1.
User Manual of DS-3WF01C-2N Figure 7-9 Router Interface – WAN Settings Click the "Add new interface" of the Interfaces page, and fill in the name of the new interface, such as ETH1, you can choose a static address for the new interface protocol, all of the current page configuration can be modified in the subsequent page.
User Manual of DS-3WF01C-2N Click "submit". Into the newly created interface configuration page, fill in the IPv4 address which should be different with LAN segments, such as 192.168.2.35. Figure 7-11 Router Interface – General Setup IPv4 gateway: In general, the IPv4 gateway address and WAN IP address are in the same network.
User Manual of DS-3WF01C-2N Figure 7-12 Router Interface - Firewall Settings 7.2 Wifi 7.2.1 Device Configuration The Device Configuration section covers physical settings of the radio hardware such as channel, transmit power or antenna selection which is shared among all defined wireless networks (if the radio hardware is multi-SSID capable). Open the Network -> Wifi page, you will see the current wireless profile and the information of associated stations.
User Manual of DS-3WF01C-2N Figure 7-14 Scanning SSID Click the SSID you need, here we select the “office-2.4G TB2I” as an example. Click on " Join Network”, it will appear the following tips as shown below, and if you check "Replace the wireless configuration", click on the confirmation will cover all current wireless template settings, please choose carefully. Figure 7-15 Join Network-1 Here we uncheck the "Replace wireless configuration", click "Submit", it will appear the following page below.
User Manual of DS-3WF01C-2N Figure 7-16 Join Network – 2 Click “Save & Apply”, wait a moment, and then Turn to Network->Wifi page, you will see the “office-2.4G TB2I” on the Associated Stations list.
User Manual of DS-3WF01C-2N Figure 7-17 Join Network - 3 When the device has been added 8 wireless profiles, or there is a client mode wireless profile in the 8 profiles, click on Join Network will appear as follows. Figure 7-18 Join Network - 4 Click the Add button to add more wireless profiles, the device can add up to eight wireless profiles, and the device can only have one client mode profile, you can choose to enable or disable the added wireless profiles.
User Manual of DS-3WF01C-2N Figure 7-19 Add Wireless Profile Click the Edit button; you can enter the wireless configuration page. The basic settings page as shown below.
User Manual of DS-3WF01C-2N Figure 7-20 General Setup Channel：The channel can be modified when the device is configured to Access Point mode or WDS Access Point mode. The device can only work on one channel at the same time. Transmit Power：The device output power. When the output power is increased, the signal distance and signal strength will be improved. Mode: You can keep the default 802.11g+n mode to guarantee optimal transmission rate.
User Manual of DS-3WF01C-2N HT Mode: Channel width selection, the device supports 20/40+/40-MHz bandwidth. In general, the wider the bandwidth is, the greater the data throughput rate. Max Transmission Rate: it can be used to limit the max transmission rate of a device. Click on Device Configuration->Advanced Settings, you can configure the advanced settings of the device in this section.
User Manual of DS-3WF01C-2N VAP Isolation: The device supports multiple VAP; if this feature is enabled, and when the client1 is connected to VAP1, the client1 will not be able to communicate the client2 which is connected to VAP2. TDMA： ： Currently, most of the outdoor bridge products are developed based on 802.11 protocols, however, it has the limitations of short-distance, hidden node problems, and poor point-to-multi-point performance.
User Manual of DS-3WF01C-2N 7.2.2 Interface Configuration Per network settings like encryption or operation mode are grouped in the Interface Configuration. Figure 7-22 Interface Configuration – General Setup ESSID: Name of a wireless. It is used to control the access to the wireless network, only the same ESSID can communicate with each other to establish a local area network. Mode: There are totally 4 wireless modes, including: Client, Access Point, Client (WDS) and Access Point (WDS).
User Manual of DS-3WF01C-2N Hide ESSID: to hide the broadcast name of the wireless network to avoid being connected to others. Check this function; others will not be able to search the SSID. Figure 7-23 Interface Configuration – Wireless Security Security: User can set the security based on needs to guarantee the wireless security. The wireless encryption of the device to be connected to each other must be set to the same encryption.
User Manual of DS-3WF01C-2N Figure 7-25 Interface Configuration – Advanced Settings Station Isolation: Enable this function, STA can’t communicate with each other. Max Station Limit: You can set the number of STA that connect to AP. 7.3 Firewall The firewall creates zones over your network interfaces to control network traffic flow. The default settings of firewall zone as shown below.
User Manual of DS-3WF01C-2N Figure 7-26 Firewall Click "modify" or "add" to define the generic properties of the zone. In the port trigger section, the forwarding rules for the current area and other areas can be modified. For example, click on Edit button of LAN zone; as shown below, this section defines common properties of "lan".
User Manual of DS-3WF01C-2N Figure 7-27 Zone The options below control the forwarding policies between this zone (lan) and other zones. Destination zones cover forwarded traffic originating from "lan". Source zones match forwarded traffic from other zones targeted at "lan". The forwarding rule is unidirectional, e.g. a forward from lan to wan does not imply a permission to forward from wan to lan as well. Figure 7-28 Inter-Zone Forwarding 7.
User Manual of DS-3WF01C-2N Figure 7-29 VLAN Settings Bridge function is needed to use together with VLAN. As show below, we add VLAN 10 on port eth0 and ath0, they are eth0.10 and ath0.10 Figure 7-30 Add VLAN ID Then we create a new interface and put eth0.10 and ath0.10 into the same bridge in Network->Interfaces page as shown below.
User Manual of DS-3WF01C-2N Figure 7-31 Binding VLAN Interfaces The packets from eth0.10 or ath0.10 will be added a VLAN label which ID is 10. That requires: the opposite wireless connection side must support VLAN 10, the device which connects with eth0 is also need to support VLAN 10 (such as a VLAN Switch).
User Manual of DS-3WF01C 3WF01C-2N Figure 7-32 VLAN Settings 7.5 Ping Watchdog Ping Watchdog：The ping watchdog sets the Device to continuously ping a user user- defined IP address (for example, it can be the IP address address of the AP the Client is connecting to). If it is unable to ping under the user defined constraints, the device will automatically reboot. It is highly recommended that users enable this feature at the side of “Station” and disable this feature at the side side of “Access Point”.
User Manual of DS-3WF01C-2N Figure 7-33 Ping Watchdog Ping IP Address：Specify an IP address of the target which will be monitored by Ping Watchdog. If this feature is enabled at the side of “Client”, Ping IP Address should be the IP address of the AP the Client is connecting to.
User Manual of DS-3WF01C-2N Chapter 8 Logout Click the logout button, it will logout the device and return to the login page. Chapter 9 FAQ 1. The device cannot be started after power on. ① The Ethernet cable between the device and the POE adaptor is more than 40 meters long. ② The Ethernet cable quality is not good enough, and it should be Cat 5e or even Cat 6 cable. ③ The RJ-45 plugs are not well connected. 2. Forgot the IP address of the device.
User Manual of DS-3WF01C-2N ② The scale plate of the client is not directed at the access point. Please adjust the client and access point. ③ Switch to other wireless channel cause there are much interferences in this channel.
User Manual of DS-3WF01C-2N 5. Multiple devices are installed at the same area, the packet loss is serious. Change channel can only improve the situation for a while. ① Multiple devices are installed at the same area, and there is no plan for the frequency settings which will cause the same frequency interference. It is recommended to separate the frequency of the devices. If the channel width is 20M, the frequency difference between two devices should be more than 20MHz.
User Manual of DS-3WF01C-2N 8. I don't want anyone to connect to my device. ① Modify the password of the access point AP. Followed by click Network - > Wifi - > select corresponding SSID and click Edit - > interface configuration - > Wireless Security. For details, please reference manual 7.2.2 interface configuration section. ② To hide the ESSID of the AP.
User Manual of DS-3WF01C-2N 63
User Manual of DS-3WF01C-2N 64
