Quick Start Guide

1.2.51.32.16303-001
Cue 2C Network Camera
Quick Start Guide
V1.0.1
Foreword
General
This manual introduces the functions, installation and operations of the
camera.
Safety Instructions
The following categorized signal words with defined meaning might
appear in the Manual.
Signal Words Meaning
Indicates a medium or low potential hazard
which, if not avoided, could result in slight or
moderate injury.
Indicates a potential risk which, if not avoided,
could result in property damage, data loss, lower
performance, or unpredictable result.
Indicates a potential risk which, if not avoided,
could result in property damage, data loss, lower
performance, or unpredictable result.
Provides additional information as the emphasis
and supplement to the text.
About the Manual
●
The Manual is for reference only. If there is inconsistency between
the manual and the actual product, the actual product shall prevail.
●
We are not liable for any loss caused by the operations that do not
comply with the manual.
●
The manual would be updated according to the latest laws and
regulations of related regions. For detailed information, see the
paper manual, CD-ROM, QR code or our official website. If there
is inconsistency between paper manual and the electronic version,
the electronic version shall prevail.
●
All the designs and software are subject to change without prior
written notice. The product updates might cause some differences
between the actual product and the manual. Please contact
the customer service for the latest program and supplementary
documentation.
●
There still might be deviation in technical data, functions and
operations description, or errors in print. If there is any doubt or
dispute, please refer to our final explanation.
●
Upgrade the reader software or try other mainstream reader
software if the manual (in PDF format) cannot be opened.
●
All trademarks, registered trademarks and the company names in
the manual are the properties of their respective owners.
●
Please visit our website, contact the supplier or customer service if
there is any problem occurred when using the device.
●
If there is any uncertainty or controversy, please refer to our final
explanation.
1
Packing List
●
Open the package and check if all the components are included
before installation.
●
Contact your local retailer if anything is broken in your package.
Figure 1-1 Packing list
2
Camera Introduction
For the introduction of the device, see Figure 2-1, Figure 2-2 and Figure
2-3.
Figure 2-1 Fornt sise
Figure 2-2 SD card slot
Figure 2-3 Back side
Press and hold the reset button for 10 s to reset the device.
The pattern of the LED indicator is included in Table 2-1.
Table 2-1 LED indicator pattern
LED Indicator Status Device Status
Off
●
Powered off/LED turned off
●
Rebooting after reset
Red light on
●
Booting
●
Device malfunction
Green light flashing Waiting for network
Green light on Operating properly
Red light flashing Network connection failed
Green and red light flashing
alternately
Firmware updating
3
Imou App Operation
Follow the steps below to add the camera in the network with Imou
App.
Step 1 Scan the following QR code or search "Imou" in Google Play
or App Store to download and install Imou App.
If you have installed the app, update it to the latest version.
Figure 3-1 QR code
Step 2 Run Imou App, and then register an account for the first use.
Step 3 Connect the camera to power source with the power adapter.
Step 4 Wait for booting to be finished, and then the camera indicator
flashes with green light.
Step 5 Connect your smart phone to your Wi-Fi network, and make
sure that your smart phone is connected to Wi-Fi network with
2.4 GHz band, and then do the following operations to finish
adding camera.
Figure 3-2 Operatons
●
If you have more than one device, do step 5 to add them
one by one.
●
If the Wi-Fi network has changed or the indicator status
goes wrong, reset the camera, and then do step 5 to add
it again.
4
Installing Camera
Make sure that the mounting surface is smooth and strong enough to
hold at least three times of the device weight.
For the installation diagram and item list of the camera, see Figure 4-1.
Figure 4-1 Installion diagram
Step 1 Stick the mounting foam on the camera pedestal.
Step 2 Power up the camera.
Step 3 Adjust the monitoring angle as needed, and then attach the
pedestal on the mounting surface, press and hold it for 10 s.