Quick Start Guide
C22E-A Network Camera
Quick Start Guide
Foreword
Package Content1
Camera Introducon2
Important Safeguards and Warnings
General
Electrical Safety
Operaon and Daily Maintenance
Environment
Safety Instrucons
About the Manual
●
●
●
●
●
●
V1.0.0
T2.0 0212227
This manual introduces the funcons, installaon and operaons
of the camera.
The following categorized signal words with defined meaning
might appear in the manual.
Indicates a medium or low potenal hazard
which, if not avoided, could result in slight or
moderate injury.
Indicates a potenal risk which, if not avoided,
could result in property damage, data loss,
lower performance, or unpredictable result.
Provides addional informaon as the
emphasis and supplement to the text.
Signal Words Meaning
The manual is for reference only. If there is inconsistency
between the manual and the actual product, the actual product
shall prevail.
We are not liable for any loss caused by the operaons that do
not comply with the manual.
The manual would be updated according to the latest laws and
regulaons of related jurisdicons. For detailed informaon, refer
to the paper manual, CD-ROM, QR code or our official website. If
there is inconsistency between paper manual and the electronic
version, the electronic version shall prevail.
All the designs and soware are subject to change without prior
wrien noce. The product updates might cause some
differences between the actual product and the manual. Please
contact the customer service for the latest program and
supplementary documentaon.
●
●
●
You can clean the device body with so dry cloth, and for
stubborn stains, use the cloth with mild detergent. To avoid
possible damage on device body coang which could cause
performance decrease, do not use volale solvent such as alcohol,
benzene, diluent and so on to clean the device body, nor can
strong, abrasive detergent be used.
Dome cover is an opcal component. Do not touch or wipe the
cover with your hands directly during installaon or operaon.
For removing dust, grease or fingerprints, wipe gently with
moistened oil-free coon with diethyl or moisten so cloth. You
can also remove dust with an air blower.
●
●
●
●
Strengthen the protecon of network, device data and personal
informaon by adopng measures which include but not limited
to using strong password, changing password regularly, updang
firmware to the latest version, and isolang computer network.
For some device with old firmware versions, the ONVIF password
will not be modified automacally along with the modificaon of
the system password, and you need to upgrade the firmware or
manually update the ONVIF password.
Use standard components or accessories provided by
manufacturer and make sure that the device is installed and
maintained by professional engineers.
The surface of the image sensor should not be exposed to laser
beam radiaon.
Do not provide two or more power supply sources for the device
unless otherwise specified. A failure to follow this instrucon
might cause damage to the device.
01
0504
02
06
03
07
●
●
●
●
●
●
●
●
●
●
●
There sll might be deviaon in technical data, funcons and
operaons descripon, or errors in print. If there is any doubt or
dispute, we reserve the right of final explanaon.
Upgrade the reader soware or try other mainstream reader
soware if the manual (in PDF format) cannot be opened.
All trademarks, registered trademarks and the company names
in the manual are the properes of their respecve owners.
Please visit our website, contact the supplier or customer service
if there is any problem occurring when using the device.
If there is any uncertainty or controversy, we reserve the right of
final explanaon.
●
●
●
●
●
●
●
●
●
●
●
●
●
Do not place the device in a wet, dusty, extremely hot or cold
environment, and avoid places with strong electromagnec
radiaon or unstable lighng.
Keep the device away from any liquid to avoid damage to the
internal components.
Keep the indoor device away from rain or damp to avoid fire or
lightning.
Install the device in a well-venlated place and do not block the
venlaon of the device.
Transport, use and store the device under the allowed humidity
and temperature.
Heavy stress, violent vibraon or water splash are not allowed
during transportaon, storage and installaon.
Use the factory default package or material with equal quality to
pack the device when transporng.
Install the device in the locaon where only the professional staff
with relevant knowledge of safety guards and warnings can
access.
Do not touch the heat dissipaon component of the device to
avoid scald.
Do not open or dismantle the device; there are no components
that a user can fix or replace. Opening the unit may cause water
leakage or expose components to direct light. Contact the
manufacturer or a qualified service representave to service the
device or to replace a component, including the desiccant. (Not
all models are provided with the desiccant).
It is recommended to use the device together with lightning
arrester to improve lightning protecon effect.
It is recommended to ground the device to enhance reliability.
Do not touch the CCD or the CMOS opc sensor. Use a blower to
clean dust or dirt on the lens surface. Use a dry cloth dampened
with alcohol and gently wipe away any dust on the lens.
All installaon and operaon must conform to your local electrical
safety codes.
Ensure power conforms to the Safety Extra Low Voltage (SELV),
and that the rated voltage meets limited power source standards
as specified in IEC60950-1. Note that the power supply
requirement is subject to the device label.
Make sure that the power supply is correct before operang the
device.
Please install easy-to-use device for power off before installing
wiring, which is for emergent power off when necessary.
Prevent the power cable from being trampled or pressed,
especially the plug, power socket and the juncon extruded from
the device.
Do not aim the device at an intense radiaon source, such as
lamp light and sun light; otherwise it might cause over brightness
or light marks, and affect the service life of Complementary
Metal-Oxide Semiconductor (CMOS).
Unpack the box and check if all the components are included
before installaon.
Contact your local retailer if anything is broken in your package.
Press and hold the reset buon for 10 s to reset the camera.
Disconnect the camera from the power before installaon or taking
out its SD card.
See the table below for definions of camera's LED behaviors.
Power Adapter ×1 Power Cable ×1
Mounng Adhesive
×1
Camera ×1
QSG ×1
Mounng Plate ×1
Screw and Anchor
Pack ×1
Mounng Template
×1
Off
Solid red
Flashing red
Flashing green
Solid green
Flashing green and red
alternately
Network connecon failed
Waing for network
Operang properly
Firmware updang
LED Status Device Status
Powered off/LED turned off
Reboong aer reset
●
●
Boong
Device malfuncon
●
●
LED Indicator
Lens
Microphone
Reset Buon
Micro SD Card Slot
Power Port
Speaker