Quick Start Guide

1.2.51.32.16523-001
Bullet Network Camera
Quick Start Guide
V1.0.1
Foreword
General
This manual introduces the functions, installation and operations of the
camera.
Safety Instructions
The following categorized signal words with defined meaning might
appear in the Manual.
Signal Words Meaning
Indicates a medium or low potential hazard
which, if not avoided, could result in slight or
moderate injury.
Indicates a potential risk which, if not avoided,
could result in property damage, data loss, lower
performance, or unpredictable result.
Provides additional information as the emphasis
and supplement to the text.
About the Manual
●
The manual is for reference only. If there is inconsistency between
the manual and the actual product, the actual product shall prevail.
●
We are not liable for any loss caused by the operations that do not
comply with the manual.
●
The manual would be updated according to the latest laws and
regulations of related regions. For detailed information, see the
paper manual, CD-ROM, QR code or our official website. If there
is inconsistency between paper manual and the electronic version,
the electronic version shall prevail.
●
All the designs and software are subject to change without prior
written notice. The product updates might cause some differences
between the actual product and the manual. Please contact
the customer service for the latest program and supplementary
documentation.
●
There still might be deviation in technical data, functions and
operations description, or errors in print. If there is any doubt or
dispute, please refer to our final explanation.
●
Upgrade the reader software or try other mainstream reader
software if the manual (in PDF format) cannot be opened.
●
All trademarks, registered trademarks and the company names in
the manual are the properties of their respective owners.
●
Please visit our website, contact the supplier or customer service if
there is any problem occurred when using the device.
●
If there is any uncertainty or controversy, please refer to our final
explanation.
Important Safeguards and Warnings
Please enter the information according to different production lines.
Electrical Safety
●
All installation and operation shall conform to your local electrical
safety codes.
●
The power source shall conform to the Safety Extra Low Voltage
(SELV) standard, and supply power with rated voltage which
conforms to Limited power Source requirement according to
IEC60950-1. Note that the power supply requirement is subject to
the device label.
●
Make sure that the power supply is correct before operating the
device.
●
A readily accessible disconnecting device shall be incorporated in
the building installation wiring.
●
Prevent the power cable from being trampled or pressed, especially
the plug, power socket and the junction extruded from the device.
Environment
●
Do not aim the device at strong light to focus, such as lamp
light and sun light; otherwise it might cause over brightness or
light marks, which are not the device malfunction, and affect the
longevity of Complementary Metal-Oxide Semiconductor (CMOS).
●
Do not place the device in a damp, dusty extremely hot or cold
environment, or the locations with strong electromagnetic radiation
or unstable lighting.
●
Keep the device away from any liquid to avoid damage to the
internal components.
●
Keep the indoor device away from rain or damp to avoid fire or
lightning.
●
Keep sound ventilation to avoid heat accumulation.
●
Transport, use and store the device within the range of allowed
humidity and temperature.
●
Heavy stress, violent vibration or water splash are not allowed
during transportation, storage and installation.
●
Pack the device with standard factory packaging or the equivalent
material when transporting the device.
●
Install the device in the location where only the professional staff
with relevant knowledge of safety guards and warnings can access.
The accidental injury might happen to the non-professionals who
enter the installation area when the device is operating normally.
Operation and Daily Maintenance
●
Do not touch the heat dissipation component of the device to avoid
scald.
●
Carefully follow the instructions in the manual when performing
any disassembly operation about the device; otherwise, it might
cause water leakage or poor image quality due to unprofessional
disassembly. Please contact after-sale service for desiccant
replacement if there is condensed fog on the lens after unpacking
or when the desiccant turns green. (Not all models are included
with the desiccant).
●
It is recommended to use the device together with lightning arrester
to improve lightning protection effect.
●
It is recommended to ground the device to enhance reliability.
●
Do not touch the image sensor (CMOS) directly. Dust and dirt could
be removed with air blower, or you can wipe the lens gently with
soft cloth that is moistened with alcohol.
●
You can clean the device body with soft dry cloth, and for stubborn
stains, use the cloth with mild detergent. To avoid possible damage
on device body coating which could cause performance decrease,
do not use volatile solvent such as alcohol, benzene, diluent and so
on to clean the device body, nor can strong, abrasive detergent be
used.
●
Dome cover is an optical component. Do not touch or wipe the
cover with your hands directly during installation or operation. For
removing dust, grease or fingerprints, wipe gently with moistened
oil-free cotton with diethyl or moisten soft cloth. You can also
remove dust with an air blower.
●
Strengthen the protection of network, device data and personal
information by adopting measures which include but not limited to
using strong password, modifying password regularly, upgrading
firmware to the latest version, and isolating computer network.
For some device with old firmware versions, the ONVIF password
will not be modified automatically along with the modification of
the system password, and you need to upgrade the firmware or
manually update the ONVIF password.
●
Use standard components or accessories provided by
manufacturer and make sure that the device is installed and
maintained by professional engineers.
●
The surface of the image sensor should not be exposed to laser
beam radiation in an environment where a laser beam device is
used.
●
Do not provide two or more power supply sources for the device
unless otherwise specified. A failure to follow this instruction might
cause damage to the device.
1
Packing List
●
Open the package and check if all the components are included
before installation.
●
Contact your local retailer if anything is broken in your package.
Figure 1-1 Packing list
Screw Package ×1
Camera ×1
Positioning Map ×1
QSG ×1
Power Adapter ×1
Waterproof Connector ×1
2
Camera Introduction
For the introduction of the device, see Figure 2-1 and Figure 2-2 .
Figure 2-1 Component
LED Indicator
Lens
Reset Button
Built-in Mic
Wi-Fi Antenna
Figure 2-2 SD card slot
Micro SD Card Slot
Press and hold the reset button for 10 s to reset the device.
The pattern of the LED indicator is included in Table 2-1.
Table 2-1 LED indicator pattern
LED Indicator Status Device Status
Off
●
Powered off/LED turned off
●
Rebooting after reset
Red light on
●
Booting
●
Device malfunction
Green light flashing Waiting for network
Green light on Operating properly
Red light flashing Network connection failed
Green and red light flashing
alternately
Firmware updating
3
Imou Life App Operation
Follow the steps below to add the camera in the network with Imou Life
App.
Step 1 Scan the following QR code or search "Imou Life" in Google
Play or App Store to download and install the app.
If you have installed the app, update it to the latest version.