AXYU Module Datasheet Version: 20211102 Online Version
Contents Contents 1 Product overview 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 2 2 Module interfaces 2.1 Dimensions and footprint . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Pin definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 3 3 Electrical parameters 3.1 Absolute electrical parameters . . 3.2 Working conditions . . . . . . . . 3.
Contents AXYU is a low-power-consumption embedded Wi-Fi 6+Bluetooth module that Tuya has developed. Embedded with the Wi-Fi network protocol stack and rich library functions, it consists of a highly integrated wireless RF chip (ECR6600-TS2D).
1 Product overview 1 Product overview With the maximum clock rate of 240 MHz, AXYU also contains a low-powerconsumption Andes D10 MCU, a WLAN MAC, a 1T1R WLAN, a 292-KB SRAM, a 2-MB flash memory, and extensive peripherals. AXYU is an RTOS platform that integrates all function libraries of the Wi-Fi MAC and TCP/IP protocol. You can develop embedded Wi-Fi products as required. 1.
2 Module interfaces 2 Module interfaces 2.1 Dimensions and footprint AXYU has 3 lines of pins. The distance between two pins at two sides is 1.4 mm, and the distance between two pins at the bottom is 1.8 mm. The dimensions of AXYU are 15.8±0.35 mm (W)×20.3±0.35 mm (L) ×2.6±0.15 mm (H). The dimensions of AXYU are as follows: 2.
2 Module interfaces Pin number Symbol Type Function 1 P00 I/O GPIO_00, common GPIO, which can be reused as SPI_SCK and corresponds to Pin 25 of the IC 2 P02 I/O GPIO_02, common GPIO, which can be reused as SPI_MOSI and corresponds to Pin 23 of the IC 3 P21 I/O GPIO_21, common GPIO, correspond to Pin 6 of the IC 4 P16 I/O GPIO_16, common GPIO, correspond to Pin 10 of the IC 5 ADC I/O GPIO_20, common GPIO, which can be used as ADC. The range of input voltage is 0 to 3.3V.
2 Module interfaces Pin number Symbol Type Function 7 L_TX I/O GPIO_13, UART_Log_TXD (used to send information about the internal logs of the module), which can be configured as a common GPIO 8 P24 I/O GPIO_24, hardware PWM, correspond to Pin 8 of the IC 9 P25 I/O GPIO_25, hardware PWM, correspond to Pin 7 of the IC 10 P22 I/O GPIO_22, hardware PWM, correspond to Pin 4 of the IC 11 P23 I/O GPIO_23, hardware PWM, correspond to Pin 3 of the IC 12 P04 I/O GPIO_04, hardware PWM, corr
2 Module interfaces Pin number Symbol Type Function 16 RXD I/O GPIO_5, UART0_RXD (user serial interface) 17 P15 I/O GPIO_15, common GPIO, correspond to Pin 28 of the IC 18 RST I/O Reset pin, reset at low level. The module has been pulled to a high level and the user can control the pin externally.
3 Electrical parameters 3 Electrical parameters 3.1 Absolute electrical parameters Minimum value Maximum value Unit Parameter Description Ts Storage temperature -40 125 ℃ VDD Power supply voltage -0.3 3.6 V ESD voltage (human body model) TAMB-25℃ - 2 KV ESD voltage (machine model) TAMB-25℃ - 0.5 KV 3.2 Working conditions Minimum Parameter Description value Typical value Maximum value Unit Ta Operating -40 temperature - 105 ℃ VDD Operating 3.0 voltage - 3.
3 Electrical parameters Minimum Parameter Description value Typical value Maximum value Unit VOL Voltage output low - - 0.1vdd V VOH Voltage output high 0.9vdd - - V Imax Drive current - 4 - mA Cpad Input pin capacitance - 2 - pF 3.
3 Electrical parameters Peak value (Typical value) Unit Symbol Mode Power Average value IRF 11ax HT20 MCS0 17dBm 213 214 mA IRF 11ax HT20 MCS7 14dBm 179 180 mA RX power consumption: Symbol Mode Average value Peak value (Typical value) IRF 11B 1M 32 32 mA IRF 11B 11M 32 32 mA IRF 11G 6M 33 33 mA IRF 11G 54M 34 34 mA IRF 11N HT20 MCS0 33 33 mA IRF 11N HT20 MCS7 34 34 mA IRF 11N HT40 MCS0 37 37 mA IRF 11N HT40 MCS7 38 38 mA IRF 11AX HE20 MCS0 32
3 Electrical parameters Working mode Working status, TA = 25°C Average value Peak value (Typical value) Unit Fast network configuration (AP) The module is in fast network configuration state and the Wi-Fi indicator flashes slowly 40 210 mA Fast network configuration (EZ) The module is in fast network configuration state and the Wi-Fi indicator flashes fast 40 197 mA Fast network configuration (Bluetooth) The module is in fast network configuration state and the Wi-Fi indicator flashes fast
3 Electrical parameters Working mode Working status, TA = 25°C Average value Peak value (Typical value) Unit Disconnected state The module is disconnected and the Wi-Fi indicator is off 35 51 mA The router is not powered The module is disconnected and the Wi-Fi indicator is off 34 84 mA 11 / 32
4 RF parameters 4 RF parameters 4.1 Basic RF features Parameter Description Frequency range 2.400 to 2.4835 GHz Wi-Fi standard IEEE 802.11b/g/n/ax (channels 1 to 14) Bluetooth standard Bluetooth 5.1 Data transmission rate 11b: 1, 2, 5.5, and 11 (Mbps) Data transmission rate 11g: 6, 9, 12, 18, 24, 36, 48, 54 (Mbps) Data transmission rate 11n: HT20 MCS0 to 7 Data transmission rate 11n: HT40 MCS0 to 7 Data transmission rate 11ax: HE20 MCS0 to 7 Antenna type PCB antenna with a gain of 1.
4 RF parameters Minimum value Typical value Maximum value Unit Average RF output power, 802.11g OFDM Mode 54M - 15 - dBm Average RF output power, 802.11n HT20 OFDM Mode MCS0 - 17 - dBm Average RF output power, 802.11n HT20 OFDM Mode MCS7 - 14 - dBm Average RF output power, 802.11n HT40 OFDM Mode MCS0 - 15 - dBm Average RF output power, 802.11n HT40 OFDM Mode MCS7 - 13 - dBm Average RF output power, 802.
4 RF parameters Minimum value Typical value Maximum value Unit Average RF output power, 802.11ax HE20 OFDMA Mode MCS7 - 14 - dBm Average RF output power, Bluetooth 5.1 2M - 7 - dBm Frequency error -20 - 20 ppm EVM@802.11b CCK 11Mbps Mode 17dBm - - -10 dB EVM@802.11g OFDM 54Mbps Mode 15dBm - - -29 dB EVM@802.11n HT20 OFDM MCS7 Mode 14dBm - - -30 dB EVM@802.11n HT40 OFDM MCS7 Mode 13dBm - - -30 dB EVM@802.
4 RF parameters Minimum value Typical value Maximum value Unit PER<8%, RX sensitivity, 802.11b CCK Mode 1M - -95 - dBm PER<8%,RX sensitivity, 802.11b CCK Mode 11M - -86 - dBm PER<10%, RX sensitivity, 802.11g OFDM Mode 6M - -90 - dBm PER<10%, RX sensitivity, 802.11g OFDM Mode 54M - -74 - dBm PER<10%, RX sensitivity, 802.11n HT20 OFDM Mode MCS0 - -90 - dBm PER<10%, RX sensitivity, 802.11n HT20 OFDM Mode MCS7 - -71 - dBm PER<10%, RX sensitivity, 802.
4 RF parameters Minimum value Typical value Maximum value Unit PER<10%, RX sensitivity, 802.11n HT40 OFDM Mode MCS7 - -68 - dBm PER<10%, RX sensitivity, 802.11ax OFDMA Mode MCS0 - -90 - dBm PER<10%, RX sensitivity, 802.11ax OFDMA Mode MCS7 - -70 - dBm PER<10%, RX sensitivity, Bluetooth 5.1 1M - -93 - dBm PER<10%, RX sensitivity, Bluetooth 5.
5 Antenna information 5 Antenna information 5.1 Antenna type AXYU uses only the onboard PCB antenna with a gain of 1.3 dBi. 5.2 Antenna interference reduction To ensure optimal Wi-Fi performance when the Wi-Fi module uses an onboard PCB antenna, it is recommended that the antenna be at least 15 mm away from other metal parts.
6 Packaging information and production instructions 6 Packaging information and production instructions 6.1 Mechanical dimensions The mechanical dimensions of the PCB of AXYU are 15.8±0.35 mm (W)×20.3±0.35 mm (L) ×1.0±0.1 mm (H).
6 Packaging information and production instructions 19 / 32
6 Packaging information and production instructions 20 / 32
6 Packaging information and production instructions Note: The default dimensional tolerance is ±0.35 mm. If customers have specific requirements on dimensions, they should make them clear in the module datasheet after communication. 6.
6 Packaging information and production instructions 22 / 32
6 Packaging information and production instructions 6.
6 Packaging information and production instructions 6.4 Production instructions 1. For the modules that can be packaged with the SMT or in an in-line way, you can select either of them according to the PCB design solutions of customers. If a PCB is designed to be SMT-packaged, package the module with the SMT. If a PCB is designed to be in-line-packaged, package the module in an in-line way. After being unpacked, the module must be soldered within 24 hours.
6 Packaging information and production instructions 1 2 3  3. The module needs to be baked in the following cases: • • • • • The packaging bag is damaged before unpacking. There is no humidity indicator card (HIC) in the packaging bag. After unpacking, circles of 10% and above on the HIC become pink.
6 Packaging information and production instructions Manner 1: SMT process (Recommended oven temperature curve of reflow soldering) Set oven temperatures according to the following curve.
6 Packaging information and production instructions Set oven temperatures according to the following temperature curve of wave soldering. The peak temperature is 260°C±5°C.
6 Packaging information and production instructions 6.
7 MOQ and packaging information 7 MOQ and packaging information Product model MOQ (pcs) Packaging method AXYU 4400 Tape reel 29 / 32 The number of modules per reel The number of reels per carton 1100 4
8 Appendix: Statement 8 Appendix: Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
8 Appendix: Statement The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
8 Appendix: Statement This product must not be disposed of as normal household waste, by the EU directive for waste electrical and electronic equipment (WEEE-2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point. The device could be used with a separation distance of 20cm.