User Manual

ManualsBrandsHank Smart Tech ManualsFlood SensorHank Smart Tech HKSWL-FLD08 Flood Sensor

Flood Sensor User Manual

HKSWL-FLD08

Note: If you have any questions about the APP or device, please click Profile->Feedback

to fill your feedback to us in APP.

1. PRODUCT OVERVIEW

HKSWL-FLD08 is a smart flood sensor (water leak sensor) based on wireless solution.

While a water leak happens, the device will wake up the Wi-Fi connection to Wi-Fi

router, send an alarm signal to your mobile phone via Wi-Fi network, in the case that

the APP internet is available locally or remotely. The alarm is selectable as a

notification on your mobile phone with bar display, banner with tone, vibration

based on the APP Notification setting on your Mobile Phone. There is an around

5-second delay from the state changes to notification on your mobile phone

depending on the internet connection quality.

The device will buzz if a water leak is detected till the leak is removed.

This device is working as a scene to trigger other device action that are compatible in

same APP such as to turn on/off plug and bulb.

PRODUCT FEATURES

 Support buzz in water leak situation

 Working in 802.11 b/g/n;

Summary of content (13 pages)

PAGE 1
Flood Sensor User Manual HKSWL-FLD08 Note: If you have any questions about the APP or device, please click Profile->Feedback to fill your feedback to us in APP. 1. PRODUCT OVERVIEW HKSWL-FLD08 is a smart flood sensor (water leak sensor) based on wireless solution. While a water leak happens, the device will wake up the Wi-Fi connection to Wi-Fi router, send an alarm signal to your mobile phone via Wi-Fi network, in the case that the APP internet is available locally or remotely.
PAGE 2
       Support EZ (Smart Config) and AP(Access Point) mode for Wireless connection; Support water leak detection; Support battery level detection and low battery alarm; Support 2xAAA battery powered; Wall mounted installation with extended detecting cable to 2 meters; Led indicates the working state; Compliant with CE, FCC and ROHS; How to Get the device working：  Make sure your Wi-Fi network work in 802.11 b/g/n 2.
PAGE 3
 Flash once in Blue: Wi-Fi connected and water leak detected;  Flash once in Dual-Color: Wi-Fi disconnected and water leak detected; 2) Probe: extend to detect the water leak; 3) Buzz vent: Sounds while water leak detected; 4) Button: Press and hold the button for 5 seconds to enter into Wi-Fi connection (or configuration). The red LED indicator will blink rapidly (EZ mode) or slowly (AP mode). EZ mode connection is set as default in Wi-Fi configuration.
PAGE 4
Android & iOS 6. ADD AND REMOVE DEVICE IN YOUR APP ACCOUNT 6.1 Launch the APP and login, Click ADD DEVICES -> Sensors -> Flood Detector to start the device adding. 6.2 Press the device button for 5 seconds to enter the Wi-Fi configuration state (fast blinking in EZ mode or slow blinking in AP mode). 6.3 Input the Wi-Fi SSID and password of the Wi-Fi network that the device is going to work with, then waiting around 30 seconds for the Wi-Fi configuration finished until a device is successfully added; 6.
PAGE 5
Note: *Make sure the device and APP work in same Wi-Fi configuration mode, both in EZ mode or in AP mode. Refer to Section 3 product description LED indicator part to check which state the device is working with. *In some case that the EZ mode is not working Wi-Fi network, AP mode is the only option.  EZ mode: make sure your APP is internet available and device and APP both work in EZ mode. Then input the Wi-Fi network password to finish the device adding.
PAGE 6
After the device is successfully added to APP account, the LED will turn off. Using the methods mentioned in LED indicator to check the device is successfully added or not. If not, please repeat the Device adding again. 6.6 Remove device 1) Click “Remove Device” to remove this device from your account; click “Restore manufacturer Defaults” to remove the device from your account and clear the history record in cloud.
PAGE 7
2) After remove device or Restore manufacturer defaults from the APP, repeating the Device add steps to your account; 7. INSTALLATION 7.1 AAA battery installation 1) Hold the battery cover and rotate it counter-clockwise to open the battery cover 2) Put 2xAAA battery in with the correct positive and negative electrode.
PAGE 8
3) Close the cover and turn it clockwise 7.2 Mount the device on the wall There are two methods to mount the device on the wall.     3M Tape mode Stick the included self-adhesive pads to the bottom of the device. Peel off the protective layer of the sticker. Stick the device onto the wall.
PAGE 9
 Screw mode 1) Mark a hole location as below picture and drill a hole on the wall accordingly. 2) Screw the two bolts within the package on the wall leaving the around 5~8mm bolt margin out of the wall. Then hang the device on the two bolts. 7.3 Install the probe case on the wall with a 3M tape, keep no gap between the probe and floor.
PAGE 10
8. FCC NOTICE (for USA) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference 2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications or change to this equipment.
PAGE 11
To maintain compliance with FCC's RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body 9. FAQ Q: The device fails to be added in account? A: 1. Make sure the Wi-Fi network is 802.11 b/g/n 2.4GHz; 2. Make sure the device works with APP in same Wi-Fi Configuration mode: EZ or AP; 3. Make sure the input SSID and password of the Wi-Fi network are correct; 4. Make sure Wi-Fi internet connection is working fine; 5.
PAGE 12
If you have any questions about the APP or device, please click Profile -> Feedback to fill your feedback to us in APP
PAGE 13
Or Check the Profile -> FAQ to find some answers.