User's Manual

ManualsBrandsHanna Instruments ManualsThermometerHanna Instruments Hanna Instruments Thermometer Stick pH & Temperature Meter

Instruction Manual

HI 9214

Stick pH & Temperature Meter

www.hannainst.com

WARRANTY

All Hanna Instruments meters are warranted for two years against

defects in workmanship and materials when used for their intended pur-

pose and maintained according to instructions. Electrodes and probes

are warranted for a period of six months. This warranty is limited

to repair or replacement free of charge.

Damages due to accident, misuse, tampering or lack of prescribed main-

tenance are not covered.

If service is required, contact the dealer from whom you purchased the

instrument. If under warranty, report the model number, date of purchase,

serial number and the nature of the failure. If the repair is not covered by

the warranty, you will be notified of the charges incurred. If the instrument

is to be returned to Hanna Instruments, first obtain a Returned Goods

Authorization Number from the Customer Service department and then

send it with shipment costs prepaid. When shipping any instrument, make

sure it is properly packaged for complete protection.

All rights are reserved. Reproduction in whole or in part is prohibited

without the written consent of the copyright owner.

Dear Customer,

Thank you for choosing a Hanna product.

This manual will provide you with the necessary information

for correct operation of the meter. Please read it carefully

before using the meter.

If you need additional technical information, do not hesitate

to e-mail us at tech@hannainst.com.

This instrument is in compliance with the directives.

Remove the instrument from the packing material and exam-

ine it carefully to make sure that no damage has occurred

during shipment. If there is any damage, notify your Dealer.

HI 9214 is supplied complete with:

• HI 12170 pH electrode

• HI 710003 soft carrying case

• 9V battery and instruction manual.

Note: Conserve all packing material until the instrument has

been observed to function correctly. Any defective item

must be returned in its original packing.

PRELIMINARY EXAMINATION

GENERAL DESCRIPTION

HI 9214 is a compact, stick-type, microprocessor-based pH/°C

meter designed to be easily carried anywhere.

Main features are: interchangeable plastic-body electrode,

simple controls on the front panel, low battery detector, simple

calibration procedure and lightweight ABS plastic housing.

The HI 12170 pH-electrode has a built-in temperature sensor

for quick and accurate temperature measurements, and auto-

matic temperature compensation.

The meter has three memorized buffer values (pH 4.01, pH

7.01, pH 10.01) and automatic buffer recognition to avoid

errors during calibration. There are no trimmers making

calibration an easy process, even for non-technical personnel.

The electrode screws directly onto the meter’s housing without

requiring cables or separate temperature probes.

The electrode Ultem

body is rugged and will stand up to

the effects of most chemicals in the lab and industry.

FUNCTIONAL DESCRIPTION SPECIFICATIONS

1) SET/HOLD key, to change measurement range, confirm

values during calibration, and freeze readings on the

LCD

2) CAL key, to enter calibration mode

3) ON/OFF key, to switch the meter ON and OFF

4) Liquid Crystal Display

5) Screw-type socket for HI 12170 pH-electrode

Range -2.00 to 16.00 pH / -5.0 to 70.0 °C

Resolution 0.01 pH / 0.1 °C

Accuracy (@20°C/68°F) ±0.02 pH / ±0.5 °C

Typical EMC Deviation ±0.02 pH / ±0.4°C

pH Calibration Automatic, 1 or 2 point,

with 3 memorized buffer values

Temperature Compensation Automatic

pH Electrode HI 12170, plastic body, gel filled,

with internal temperature sensor and

screw connector (included)

Battery Type 1 x 9V, alkaline

Battery Life 700 hours of continuous use

Auto-off after 8 minutes of non-use

Environment 0 to 50°C (32 to 122°F);

RH max 95% non-condensing

Dimensions 185 x 42 x 26 mm (7.3 x 1.7 x 1.0")

Weight 160 g (5.6 oz.)

Hanna Instruments reserves the right to modify the design, construction

and appearance of its products without advance notice.

IST9214R1 06/05

ACCESSORIES

HI 12170 Plastic body, gel filled pH electrode with built-in

temperature sensor and screw-type connector

HI 70004P pH 4.01 buffer solution, 20 mL sachet (25 pcs)

HI 70007P pH 7.01 buffer solution, 20 mL sachet (25 pcs)

HI 70010P pH 10.01 buffer solution, 20 mL sachet (25 pcs)

HI 7004L pH 4.01 buffer solution, 500 mL bottle

HI 7007L pH 7.01 buffer solution, 500 mL bottle

HI 7010L pH 10.01 buffer solution, 500 mL bottle

HI 70300L Storage solution, 500 mL bottle

HI 710003 Soft carrying case

Summary of content (2 pages)

PAGE 1
Instruction Manual HI 9214 Stick pH & Temperature Meter Dear Customer, Thank you for choosing a Hanna product. This manual will provide you with the necessary information for correct operation of the meter. Please read it carefully before using the meter. If you need additional technical information, do not hesitate to e-mail us at tech@hannainst.com. directives. This instrument is in compliance with the FUNCTIONAL DESCRIPTION Range -2.00 to 16.00 pH / -5.0 to 70.0 °C Resolution 0.01 pH / 0.
PAGE 2
OPERATIONAL GUIDE • The meter is supplied complete with a 9V battery. Remove the battery compartment cover on the back of the meter, install the battery while paying attention to its polarity. • Always remove the electrode protective cap before taking any measurements. If the electrode has been left dry, soak the tip in HI 70300 storage solution for half an hour to reactivate it. • Connect the pH electrode to the screw type connector on the meter.