User Guide

Instruction Manual
HI 38017
Free & Total
Chlorine
Low and Medium
Range
Test Kit with
Checker Disc
www.hannainst.com
Dear Customer,
Thank you for choosing a Hanna Product.
Please read the instruction sheet carefully before using the
test kit. It will provide you with the necessary information
for correct use of the kit. If you need additional information,
do not hesitate to e-mail us at [e-mail].
Remove the chemical test kit from the packing material and
examine it carefully to make sure that no damage has
occurred during shipping. If there is any noticeable dam-
age, notify your Dealer or the nearest Hanna office
immediately.
Each kit is supplied with:
•
HI 93701-0 Free Chlorine reagent, packets (100 pcs);
•
HI 93711-0 Total Chlorine reagent, packets (100 pcs);
• Demineralizer Bottle with filter cap for about 12 liters
of deionized water (depending on the hardness level
of water to be treated)
;
• 1 checker disc (containing a mirror, a mirror holder
and the disc);
• 2 glass vials with caps
;
• 1 plastic pipette (3 mL).
Note: Any damaged or defective item must be returned in
its original packing materials.
ISTR38017 02/00 PRINTED IN ITALY
Chlorine is the most commonly used water disinfectant in
applications that vary from treatment of drinking water
and wastewater, pool and spa sanitization, to food pro-
cessing and sterilization. Chlorine present in water binds
with bacteria, leaving only a part of the original quantity
(free chlorine) to continue its disinfecting action. If the free
chlorine level is improper with respect to pH, water will
have an unpleasant taste and odor and the disinfecting
potential of the chlorine will be diminished.
Free chlorine reacts with ammonium ions and organic
compounds to form chlorine compounds resulting in dimin-
ished disinfecting capabilities compared with free chlorine.
Chlorine compounds together with chloramines form com-
bined chlorine. Combined chlorine and free chlorine together
result in total chlorine.
While free chlorine has a much higher disinfectant poten-
tial, combined chlorine has a much higher stability and
has a lesser volatility.
Note: mg/L is equivalent to ppm (parts per million).
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONS
SIGNIFICANCE AND USESIGNIFICANCE AND USE
SIGNIFICANCE AND USESIGNIFICANCE AND USE
SIGNIFICANCE AND USE
CHEMICAL REACTIONCHEMICAL REACTION
CHEMICAL REACTIONCHEMICAL REACTION
CHEMICAL REACTION
INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONS
The reaction between chlorine and the DPD reagent causes
a pink tint in the sample which is proportional to the
chlorine concentration.
READ THE ENTIRE INSTRUCTIONS BEFORE USING THE KIT
• To measure chlorine in the 0-0.7 mg/L range, verify
that the mirror, its holder and the disc are pre-installed
in the checker disc. If not, install them as shown in the
figure.
• Use the pipette to fill each glass
vial with 10 mL of sample (up to
the mark).
• Insert one of the vials into the left hand opening of the
checker disc. This is the blank.
• Remove the cap and fill
the Demineralizer Bottle
with tap water.
• Replace the cap and
shake gently for at least
2 minutes. The dem-
ineralized water is now
ready.
• Flip open the top of the Demineralizer Bottle cap. By
gently squeezing the bottle, add demineralized water
to the other vial up to the 20 mL mark. Replace the
cap and shake to mix.
10 mL
• Remove the cap and add the specific test reagent:
Free Chlorine: 1 packet of Total Chlorine: 1 packet of
DPD Free Chlorine reagent. DPD Total Chlorine reagent.
• Replace the cap and mix.
• In the case of Total Chlo-
rine determination, wait
for 2 minutes to allow
reaction to occur. This is
the reacted sample.
• Remove the cap and insert
the reacted sample into the
right hand opening of the
checker disc.
• Hold the checker disc so
that a light source illumi-
nates the samples from the
top.
• Keep the checker disc at a distance of 30-40 cm (12-
16") from the eyes to match the color. Rotate the disc
while looking at the color test windows and stop when
you find the color match. Read the value in the result
window and divide it by 5 to obtain mg/L (or ppm) of
Chlorine.
Range 0 to 0.7 mg/L (ppm) as Chlorine (LR)
0 to 3.5 mg/L (ppm) as Chlorine (MR)
Smallest Increment LR: 0.02 mg/L
MR: 0.1 mg/L
Analysis Method Colorimetric
Sample Size 10 mL (LR), 5 mL (MR)
Number of Tests 200
Case Dimensions 235x175x115 mm (9.2x6.9x4.5")
Shipping Weight 696 g (24.6 oz.)