Installation and Operation Instructions ELECTRIC FIREPLACE X42RECWMEF-1BLK X42RECWMEF-1WHT X50RECWMEF-1BLK X50RECWMEF-1WHT X60RECWMEF-1BLK X60RECWMEF-1WHT REV19-01
Tool list 2 Assembly Instructions 2-3 Important Safety Instructions 3-4 Listing Approvals 5 Glass Particles Installation Instructions 6 Product Dimensions 7-8 Installation 9-11 Operating Instructions 12 Remote Control Instructions 13 Temperature Limiting Control 14 Trouble Shooting 14 Cleaning 14 1
Suggested tools: Phillip head screw driver, power drill, drill bit, and a tape measure. Unit needs to be hung on wall stud for more security and stability. (1) Fireplace assembly 1 PC (3) Remote Control (2) Steel holder WALL MOUNTING Embedded 50"/60" 42" 1pcs 1pcs 42"/50"/60" 4pcs (4) Screw 1pcs Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Avoid rubbing or scratching the surface with rough or abrasive objects.
2. The heater may emit a slight, harmless odour when first used. This odour is normal and it is caused by the initial heating of internal heater parts and will not occur again. 3. If the heater does not emit heat, Consult your User’s Guide for further information.
instruction concerning use of the appliance in a safe way and understand the hazards involved. ● Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
LISTING APPROVALS This heater has been tested in accordance with the CSA Standards. Model Number: X42RECWMEF-1BLK X42RECWMEF-1WHT X50RECWMEF-1BLK X50RECWMEF-1WHT X60RECWMEF-1BLK X60RECWMEF-1WHT Depth: Length: Height: 42.0 21.8 7.0 50.0 21.8 7.0 60.0 21.8 7.
GLASS PARTICLES INSTALLATION INSTRUCTIONS Instructions: Install the charcoal fire or glass crystal media on the plastic strip.
PRODUCT DIMENSIONS DO NOT COVER 7.0 21.
42" 50"/60" Mounting Bar 42" 50"/60" BACK VIEW PRODUCT DIMENSIONS WARNING: Due to high temperatures, this electric fireplace should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 36" from the top of the heater. WARNING: Never locate this electric fireplace where it may fall into a bathtub or other water container.
UNPACKING AND TESTING FIREPLACE Carefully remove the unit from the box. Prior to installing the unit, test to make sure the unit operates properly. To do this, plug the unit's power supply cord into a conveniently located 120 Volt grounded outlet. INSTALLATION WARNING: RISK OF FIRE! The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce risk of fire, electric shock or personal injury. Do not run cord under carpeting.
INSTALLATION INSTALLATION INSTRUCTIONS ACCESSORY DRAWING 42" 50"/60" Wall hook Embedded mount There are 3 ways to install the product. Please follow the steps to install machine: 1.WALL MOUNTING ② lock screws Direction ① 50"/60" ③ 42" ①Mount the hook on the wall and fix the screws (4*40mm) ②Mount the fireplace on the hook ③lock 3 screws in total 2.
3.EMBEDDED (INNER INSTALLATION) Direction ① ② Direction Direction Direction 2 Screws ③ 4 Screws ④ Direction lock screws lock screws (4*40mm) (4*40mm) lock screws lock screws (4*40mm) (4*40mm) ⑤ ⑥ Direction Direction Direction ⑦ ⑧ ⑨ Direction ⑩ ①.Remove the acrylic plate ⑥.Fix the fireplace to the wall ②.Remove the glass bead ⑦.Restore glass ③.Remove the plastic glass buckle ⑧.Restore plastic glass buckle ④.Remove the glass ⑨.Restore the glass bead ⑤.
OPERATING INSTRUCTIONS 1 2 3 4 LOCATION The master power switch is located on the right side of the appliance. The control panel is on the right corner of the glass. MASTER SWITCH The master switch controls the power supply to the appliance. Turn the switch to “I” to connect power and turn the switch to “O” to cut the power. There will be a chiming sound when turning to “I”. 1.
REMOTE CONTROL FEATURES 1. Install the CR2025 3V battery in the remote control. 2. Turn the master switch on the e-fireplace to ‘I’ so that it can receive the signal from the remote control. 3. Lock the colour for the flame using button 1. Lock the colour for the Log using button 2. Press the button 1 2 to see and choose the colour. 4. CAUTION: Never leave the e-fireplace unattended while heating. 5. Refer to Page 11 control buttons/functions for the other buttons on the remote control.
TEMPERATURE LIMITING CONTROL This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, (115 degrees Celsius) the heater will automatically turn off. To reset: Unplug unit from wall, wait for 5 minutes, plug back in and continue to use. TROUBLE SHOOTING SYMPTOM Fireplace doesn't work. Fireplace inner components are overheating or the home circuit breaker has tripped.
