Installation and Operation Instructions ELECTRIC FIREPLACE F56WMEF
Suggested tools: Phillip head screw driver, power drill, drill bit, and a tape measure. Unit needs to be hung on wall stud for more security and stability. (1) Fireplace assembly 1 PC (3) Remote Control (2) Steel holder 1 PC (4) Screw RGB 1PCS 8 PCS ￠4mm x 40mm Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Avoid rubbing or scratching the surface with rough or abrasive objects.
CAM56WMEF Remote Control Electric Wall-Mount Fireplace Assembly Instructions Quick Reference Guide 1. Prior to plugging your heater into a convenient outlet, first verify that the circuit breaker for the outlet is on. 2. The heater may emit a slight, harmless odor when first used. This odor is normal and it is caused by the initial heating of internal heater parts and will not occur again. 3. If the heater does not emit heat, consult your Practical User’s Guide for further information.
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, to reduce the risk of fire, electric shock and injury to persons, basic precautions should always be followed, including the following: . 1. Read all instructions before use. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided use handle when moving this heater. 3.
LISTING APPROVALS This heater has been tested in accordance with the CSA Standards. Model Number: X56WMEF Description: Wall Mount Electric Fireplace Voltage: 120V AC, 60Hz Watts: MAX 1350W Length: Height: 56.0 20.2 Depth: 4.
GLASS PARTICLES INSTALLATION INSTRUCTIONS 1. Removing the outer glass around the bracket, mounting screws (red 2. Remove the outer glass, to be put flat, scratch concern 3. glass particles into the slot neatly bagged glass 4.
PRODUCT DIMENSIONS 4.7 20.2 56.
PRODUCT DIMENSIONS WARNING: Due to high temperatures, this electric fireplace should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 0.9m from the top of the heater. WARNING: Never locate this electric fireplace where it may fall into a bathtub or other water container. CAUTION: Do not expose the electric fireplace to the elements (such as rain, ect.
UNPACKING AND TESTING FIREPLACE Carefully remove the unit from the box. Prior to installing the unit, test to make sure the unit operates properly. To do this, plug the unit's power supply cord into a conveniently located 120 Volt grounded outlet. INSTALLATION WARNING: RISK OF FIRE! The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce risk of fire, electric shock or personal injury. Do not run cord under carpeting.
INSTALLATION Model 1: screws Model 2: Trim Piece Remove the glass pane first, set the fire box into the wall. secure the side trim pieces on the wall with screws. Reinstall the glass pane onto the firebox with screws.
OPERATING INSTRUCTIONS The manual controls are located on the left side of the fireplace. You have the following controls: 1.Power ON/OFF: Power to the unit. 2.Push the flame button for desired flame, it has 5classes flame to adjust from L1-L2-L3-L4-L5-L1…and so on. It appears the related flame on the digital screen. 3.Low heat:700 watts(LO) , High heat: 1350 watts(HI) 4. Display shows the current temperature of the boot.
TEMPERATURE LIMITING CONTROL This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, (115 degrees Celsius) the heater will automatically turn off. To reset: Unplug unit from wall, wait for 5 minutes, plug back in and continue to use. TROUBLESHOOTING The remote takes 2 x AAA batteries CLEANING Turn heater OFF and unplug from outlet. Use a vacuum or duster to keep heat and vent area clean from dust and dirt.
