Instructions / Assembly

ManualsBrandsHanover ManualsHeaters7 ft. 41,000 BTU Black Round Wicker Propane Gas Patio Heater

ASSEMBLY INSTRUCTIONS

Hardware Used

2. Attach three support brackets loosely to base with

three bolts

M8 x 16 (BB) downward through support

brackets into the Base.

3. Install post onto three support brackets. Attach

post to support brackets using six

bolts M6 x 30 (EE)

& six

M6 flange nuts (CC). Fully tighten all of the screws.

x 2

Bolt M8 x 16

M8 Flange nut

x 2

Bolt M8 x 16

x 3

x 6

M6 Flange nut

Bolt M6 x 30

x 6

Hardware Used

Fill sand

1. Line up holes on the bracket of wheel assembly (J)

with the corresponding holes on base (H), then insert

M8 x 16 mm bolts (BB) through holes. Tighten with

M8 flange nuts (AA). Be sure the wheel assembly (J) is

parallel to the base (H).

Note: To improve stability, the preassembled bucket (I)

can be filled with sand (not included). Open the lid, fill

sand then close it.

Summary of content (6 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS 1. Line up holes on the bracket of wheel assembly (J) with the corresponding holes on base (H), then insert M8 x 16 mm bolts (BB) through holes. Tighten with M8 flange nuts (AA). Be sure the wheel assembly (J) is parallel to the base (H). Note: To improve stability, the preassembled bucket (I) can be filled with sand (not included). Open the lid, fill sand then close it. 1 H I Hardware Used AA AA M8 Flange nut x2 BB Bolt M8 x 16 x2 BB 2.
PAGE 2
ASSEMBLY INSTRUCTIONS 4. Load Cylinder Housing onto Post. Slide Cylinder Housing down. 4 5. 5-1. Attach reflector spacers (FF) and three washers Ø8 (GG) to screen cover. Tighten the reflector spacers. 5-1 FF GG Hardware Used FF C x3 Reflector Spacer GG Washer Φ8 x3 5-2. Unscrew four stainless steel bolts (DD).
PAGE 3
ASSEMBLY INSTRUCTIONS 5-3. Load head assembly by inserting hose into post. Insert head assembly into post. Control knob should be above decal on post. Attach head assembly to post, and loosely install four stainless steel bolts. Tighten bolts securely. 5-3 6. WARNING:Remove protective cover before assembling. Note: If necessary for proper alignment of reflector sections, loosen each bolt prior to further assembly and retighten after sections are aligned. 6 A B 7. Slide two reflector panels together.
PAGE 4
ASSEMBLY INSTRUCTIONS 8. Slide reflector plate onto reflector panels. Insert one screw M6 X 10 (II). Slide one washer Φ 6 over threaded end of screw M6 X 10 (II) and screw on cap nut (JJ) loosely. Repeat procedure to complete the assembly of all four sections. Fully tighten all of the screws in the rolled edge. 8 JJ HH II TT 9. Support heater. Slide three washers washer Φ8 (GG) over threaded end of spacer. Locate reflector assembly on 3 spacers.
PAGE 5
ASSEMBLY INSTRUCTIONS 10. Screw gas hose and regulator (F) onto propane cylinder (not included). Do not cross-thread. WARNING: Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See chapter 5 of the standard for storage and handling of liquefied petroleum gas, ANS/NFPA 58. Your local library or fire department should have this book. A minimum supply pressure of 8” W.C. is required for the purpose of input adjustment for propane gas.
PAGE 6
ASSEMBLY INSTRUCTIONS WARNING: A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your propane supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.