Use and Care Manual

ManualsBrandsHanover ManualsHeaters7 ft. 41,000 BTU Black Round Wicker Propane Gas Patio Heater

ANS Z83.26-2014 • CSA 2.37-2014 Gas-Fired Outdoor Infrared Patio Heaters

DANGER

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. If odor continues, keep away from the appliance and

immediately call your gas supplier or fire department.

DANGER

WARNING

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

An LP-cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

CARBON MONOXIDE HAZARD

This appliance can produce

carbon monoxide which has

no odor. Using it in an enclosed

space can kill you. Never use this

appliance in an enclosed space

such as a camper, tent, car or home.

WARNING: For Outdoor Use Only

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or death.

Read the installation, operation and maintenance

instructions thoroughly before installing or servicing this

equipment.

OUTDOOR

PATIO HEATER

User Manual No. 5

Models: 9710012, 9710013

Summary of content (20 pages)

PAGE 1
User Manual No. 5 Models: 9710012, 9710013 OUTDOOR PATIO HEATER DANGER FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
PAGE 2
PACKAGE CONTENTS A B FF C D E F PART A B FF C D G H I E F J G H 2 DESCRIPTION Reflector Panel Reflector Plate Reflector Stud Head Assembly Cylinder Housing I Post Gas Hose & Regulator Support Bracket Base Bucket (preassembled) J Wheel Kit QUANTITY 3 1 3 1 1 1 1 3 1 1 1
PAGE 3
HARDWARE CONTENTS (shown actual size) AA M8 Flange nut Qty. 2 II DD CC BB Bolt M8 x 16 Qty. 5 M6 Flange nut Qty. 6 JJ Screw M6 X 10 Qty. 9 Cap nut Qty. 9 EE Stainless steel bolt Qty. 4 Bolt M6 x 30 Qty. 6 KK Wing nut Qty. 3 FF Reflector spacer Qty. 3 GG Washer Φ8 Qty. 9 HH Washer Φ6 Qty. 9 MM LL Wrench Qty. 1 (not actual size) Battery Qty. 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.
PAGE 4
SAFETY INFORMATION DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces that do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
PAGE 5
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
PAGE 6
ASSEMBLY INSTRUCTIONS 1. Line up holes on the bracket of wheel assembly (J) with the corresponding holes on base (H), then insert M8 x 16 mm bolts (BB) through holes. Tighten with M8 flange nuts (AA). Be sure the wheel assembly (J) is parallel to the base (H). Note: To improve stability, the preassembled bucket (I) can be filled with sand (not included). Open the lid, fill sand then close it. 1 H I Hardware Used AA AA M8 Flange nut x2 BB Bolt M8 x 16 x2 BB 2.
PAGE 7
ASSEMBLY INSTRUCTIONS 4. Load Cylinder Housing onto Post. Slide Cylinder Housing down. 4 5. 5-1. Attach reflector spacers (FF) and three washers Ø8 (GG) to screen cover. Tighten the reflector spacers. 5-1 FF GG Hardware Used FF C x3 Reflector Spacer GG Washer Φ8 x3 5-2. Unscrew four stainless steel bolts (DD).
PAGE 8
ASSEMBLY INSTRUCTIONS 5-3. Load head assembly by inserting hose into post. Insert head assembly into post. Control knob should be above decal on post. Attach head assembly to post, and loosely install four stainless steel bolts. Tighten bolts securely. 5-3 6. WARNING:Remove protective cover before assembling. Note: If necessary for proper alignment of reflector sections, loosen each bolt prior to further assembly and retighten after sections are aligned. 6 A B 7. Slide two reflector panels together.
PAGE 9
ASSEMBLY INSTRUCTIONS 8. Slide reflector plate onto reflector panels. Insert one screw M6 X 10 (II). Slide one washer Φ 6 over threaded end of screw M6 X 10 (II) and screw on cap nut (JJ) loosely. Repeat procedure to complete the assembly of all four sections. Fully tighten all of the screws in the rolled edge. 8 JJ HH II TT 9. Support heater. Slide three washers washer Φ8 (GG) over threaded end of spacer. Locate reflector assembly on 3 spacers.
PAGE 10
ASSEMBLY INSTRUCTIONS 10. Screw gas hose and regulator (F) onto propane cylinder (not included). Do not cross-thread. WARNING: Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See chapter 5 of the standard for storage and handling of liquefied petroleum gas, ANS/NFPA 58. Your local library or fire department should have this book. A minimum supply pressure of 8” W.C. is required for the purpose of input adjustment for propane gas.
PAGE 11
ASSEMBLY INSTRUCTIONS WARNING: A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your propane supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
PAGE 12
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the heater until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
PAGE 13
OPERATION INSTRUCTIONS DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. Before Turning Gas Supply ON: 1.
PAGE 14
OPERATION INSTRUCTIONS Lighting: 1. Turn on the valve on the gas cylinder. 2. Press and turn the control knob to HI (maximum) position (anti-clockwise 90º). (Figure 1) 3. Holding down the control knob, press the igniter button several times until the main flame is ignited. Release the control knob 10 seconds after the ignition. 4. Turn the control knob to LO (minimum) and leave it there for 5 minutes or more before turning the knob to the desired temperature setting. (Figure 2) 5.
PAGE 15
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. When Heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops.
PAGE 16
OPERATION INSTRUCTIONS 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 2 feet on top and at least 3 feet on sides from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
PAGE 17
CARE AND MAINTENANCE Signs of possible blockage include: Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage the heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
PAGE 18
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Propane cylinder is frosted over Wait until the propane cylinder warms up and is defrosted Blockage in orifice Clear blockage Control knob is not in ON position Turn control knob to ON Gas pressure is low Turn cylinder valve OFF and replace cylinder Outdoor temperature is less than 40ºF and tank is less than 1/4 full Use a full cylinder Control knob fully ON Check burner and orifices for blockage Carbon build-up Dirt or film on reflec
PAGE 19
ONE-YEAR LIMITED WARRANTY This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. The Company's obligation under the warranty is to replace or repair defective parts at our discretion.
PAGE 20
REPLACEMENT PARTS LIST A B FF C D E F PART A B FF C D G H I E F J G H 20 DESCRIPTION Reflector Panel Reflector Plate Reflector Stud Head Assembly Cylinder Housing I Post Gas Hose & Regulator Support Bracket Base Bucket (preassembled) J Wheel Kit QUANTITY 3 1 3 1 1 1 1 3 1 1 1