PERGOLA Instruction manual 比例 size/cm:392×292×228 size/inch:154×115×90 25.400 9820302 IMPORTANT You must read these instructions carefully before you start to assemble this PERGOLA .Please ensure that you find all parts in the carton box in the correct type and quantity as mentioned in the list illustrated in every page accordingly. Please carry out the steps in the order set out in these instructions. Do not tighten the steps until completing the assembly of all the parts.
8/1/2019 For additional on‐line support on assembly, troubleshooting and care & maintenance of your outdoor product, please visit our website at: www.Hanover‐Products.com. To expedite any future warranty claims, please retain your receipt for future use. www.Hanover‐Products.
SAFETY ADVICE We strongly recommend the use of work gloves during assembly. Do not attempt to assemble the PERGOLA in windy or wet conditions, Do not touch overhead power cables with the aluminum profiles. Always wear shoes and safety goggles when working with extrded aluminum. Dispose of all plastic bags safely and keep them out of reach of children. ! The PERGOLA must be positioned and fixed on a flat level surface. Do not lean against or push the PERGOLA during construction.
PRODUCT SIZE Make sure you choose a correct installation location ch 15in /1 92cm NO. Qty. 392 cm 2 / 15 4inc h 228cm / 90inch / 13 3inc h 比例 m/ 338c 25.400 cm 2 3 5 6 2 2 1 7 3 9 1 2760mm/108.6" 3760mm 148" 3439mm 135.4" nch S3 3 5 6 S5 7 9 S5 1 S3 NO. Qty. NO. Qty. B1 4 B3 21 S1 21 B15 16 S3 10 F1 16 M6(15/64) S5 4 F2 32 M6(15/64) B6 2 F3 2 B2 21 F4 4 S7 50 10 2 S3 3 7 2 2 S5 S3 5 2 133i S3 S3 S5 S3 1 2200mm/86.6" 207cm / 81.
1 x2 3 x2 2 x2 Ⅰ x4 B1 x4 F1 x16 F2 x16 S7 x32 Column,Beam Installation Ⅱ x2 Fix profile 3# onto columns with 4 pcs F2 screws on each top, total 16pcs F2 screws needed for two 3# profiles. 3 3 F2x4 2 F2x4 1 1 Profile 3# must be fixed on the lower pre-drilled holes on columns. 3 F1 F1 F1 F1 1 piece screws cap for every screw. B1 比例 25.400 -5- 比例 25.
5 x2 7 x2 S1 x14 F2 x16 S7 x16 Ⅰ x2 5 5 7 I 7 S1x7 S1x7 Insert profile 7# into the cavity of profile 5#, then insert 7pieces S1 into part 7#. Ⅱ x2 F2x4 1 piece screws cap for every screw. II Fix the combination part 7# and 5# onto the columns with 16 pieces F2 screws.
S7 x2 6 7 Ⅰ 6 F3 F3 6 I 7 7 Ⅱ II 6 F3 Fix the combination part 7# and 6# onto the columns with 2 pieces F2 screws. 2 1 Ⅱ 3 6 5 7 1 5 7 Ⅱ 2 3 3 3 -7- Insert profile 7# into the cavity of profile 6#, then insert 7pieces S1 into part 7#.
F4x4 B6 x2 Installation for Magnet Fixer B6 Ⅰ Ⅰ x2 5 6 5 7 6 7 7 B6 F4 F4 Install part B6 onto parts 7 fixed on parts 3#. 1 piece B6 on each side.
S3 x10 B15 x16 S5 x4 Ⅰ x2 S3 Plastic end caps installation S5 6 S3 S5 S3 Ⅱ x4 S5 3 S3 S3 S5 S5 S3 S3 S3 S3 S3 S3 S3 S3 3 1 7 Ⅲ B15 x4 x4 B1 B15 x4 B1 B15 x4 B1 B15 x4 B15 x4 -9- B1 B1
Hang part B8 onto S1; Hang fabric 9# onto part B8 with Strip B9. S1 7 S1 B8 Ⅰ x21 9 B9 x21 B8 x21 Ⅲ 3 5 7 9 B8 9 B9 Ⅱ x21 Ⅲ x2 7 B8 B9 9 10 5 10 S1 -10- 10 x2 Hang Pulling strip on the first and last pole of fabric.
Maintenance: 1.If the ground is not level, the unit may tilt to one side. If you find this is the case, please fix immediately to avoid damage. 2.Please prevent adding any increased weight to the product. 3.Avoid any vine/climbing plants, fruits, or vegetables from growing on the pergola as to not compromise the structure and durability of the product. If the structure is compromised, it can easily cause the frame to crack, break, or collapse. Fabric Maintenance: 1.
1‐877‐397‐5144 www.Hanover‐Products.com or ContactUs.Hanover‐Products.com Or email us at: Contact Warranty Services at 8/1/2019 THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS.