Hanover Outdoor Furniture IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues, etc.), PLEASE DO NOT RETURN TO THE RETAILER/STORE from where you purchased the product. Please call our Toll‐Free Customer Service Hotline at: 1‐800‐416‐3511 Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday Or visit our website at: www.hanover‐products.
Outdoor Furniture 1-Year Limited Warranty Program For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty revert back to the date of original purchase for future warranty.
Care & Maintenance Outdoor furniture can be enjoyed for many years when well maintained. Regular Maintenance Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air. For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution areas.
ASSEMBLY INSTRUCTIONS 1 Position the swivel base on a flat, solid surface. Make sure the swivel plate is positioned all the way into the base. It may have vibrated out during shipment. The two sets of holes in the swivel plate should be facing away from you. Note the arrows on both the swivel plate and the "U" bar portion of the chair frame.
PARTS IDENTIFICATION LIST * NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE PARTS LIST DESCRIPTION ORDER PART # QTY A CHAIR FRAME AB1296 1 B SWIVEL ASSEMBLY & BASE AB1297 1 C 5/16" X 43 MM BOLT HW0450 4 D Ø8.0 X 2.3 MM SPRING WASHER HW0003 4 E METAL PLATE HW0847 2 F 5/16" NUT HW0015 4 G Ø8.5 X 1.
ASSEMBLY INSTRUCTIONS CSA Model 98300 ARV08300 Installer: Leave these instructions with consumer. Consumer: Keep these instructions for future reference. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: Improper installation, adjustment alteration, service or maintenance can cause injury or property damage.
TABLE OF CONTENTS Important Safety Information 3 Important About Propane 4 Specification 4 Parts Identification List 5-6 Installation 7-11 Natural Gas Conversion 12 Lighting Instructions 13 Batteries 14 Maintenance 14 Troubleshooting Guide 15 Warranty 16 2
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS A self contained LP-gas cylinder for use with this appliance must have a capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD (overfill protection device). See Figure 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S.
PARTS IDENTIFICATION LIST PART DESCRIPTION PART# QTY A CONTROL KNOB FP0245 1 B GAS VALVE FP0307 1 C THERMOCOUPLE FP0004 1 D LP REGULATOR HOSE FP1329 1 E ELECTRODE FP1330 1 F GAS TUBE FP1689 1 G ORIFICE ELBOW FP1385 1 H IGNITION MODULE FP1666 1 I ORIFICE BRACKET FP1667 1 J PROPANE ORIFICE FP1299 1 K NATURAL GAS ORIFICE FP1300 1 L “AAA” BATTERY(1.
T MIDDLE PANEL FP1750 1 U BOTTOM PANEL FP1751 1 V BACK PANEL FP1752 1 W DOOR PANEL FP1753 1 Y BURNER COVER FP1754 1 Z BURNER COVER PROTECTIVE RING FP1755 1 AA FIREPAN/BURNER ASSEMBLY FP1756 1 BB SUPPORT BAR-1 FP1757 1 CC SUPPORT BAR-2 FP1758 1 6
INSTALLATION 1. Identify parts packed in carton against the parts list. Remove all protective materials and set parts on a flat, non-abrasive surface. IMPORTANT NOTE: WE RECOMMEND TWO PEOPLE WORK TOGETHER TO ASSEMBLE THE PRODUCT. 2. Place the back panel upside down on a flat, non-abrasive surface. Open it as shown in Figure 2. Figure 2 3. Assemble the door panel to the back panel as shown in Figure 3.
4. Attach the bottom panel to legs by using four 1/4"x30 mm bolts and washers as shown in Figure 4.Guide the bolts through holes in the bottom panel, into pre-drilled holes in the legs. Hand tighten only. Figure 4 5. Carefully place the middle panel inside back panel with bottom panel as shown in Figure 5.
6. Attach the bottom panel to the back panel by using two 1/4"x30 mm bolts and washers as shown in Figure 6. Guide the bolts through holes in the bottom panel, into pre-drilled holes in the back panel. Hand tighten only. Figure 6 7. Attach the two support bars to the firepan/burner assembly by using two 1/4"x30 mm bolts and washers as shown in Figure 7. Hand tighten only. Figure 7 8.
9. After making any necessary adjustments to the alignment of the all parts, use the hex bolt driver to tighten all bolts. Do not over tighten. Over tightening may strip bolts. 10. With the help of another person, Attach the table top to the complete base by using four 1/4"x20 mm bolts and washers as shown in Figure 9. Guide the bolts through the holes in the side panels, into the pre-drilled holes in the table top. Do not tighten completely.
12. Tighten threaded knobs (L) found on tank tray (Figure.11) so that the LP tank cannot move from side to side. Do not remove plastic cap from end of threaded section. Figure 11 13. Pour the lava rocks (not included) into the burner pan completely covering the burner. See Figure 12. BURNER PAN IGNITION WELL Figure 12 14. Remove the cardboard cover from the ignition well as shown in Figure 12. Remove any lava rock or fire ice on top of ignition well. Figure 13 CARDBOARD COVER 15. Open the tank valve.
NATURAL GAS CONVERSION Natural gas conversion must be performed only by your natural gas provider or service company. Step 1- At the control panel, disconnect the rubber gas hose from the gas valve. Step 2- Below the burner, disconnect the aluminum gas tube from the orifice elbow. Step 3- Remove the 2 M4 nuts from the orifice holder and remove the orifice bracket assembly. Step 4- Disconnect the orifice from the elbow and replace it with the Natural Gas orifice from the kit.
Step 5- Stick the conversion label on the rating plate as shown in Figure 15. Metal Rating Plate Serial Number _________________ Model Number: 98900 1. must be used. This regulator is set for an outlet pressure of CAUTION: The gas pressure regulator provided with this appliance 2. This appliance has been converted to use Natural Gas. 3. Input 40,000 Btu/hr. Max Gas Supply Pressure 7 inch w.c. (1.74 kPa) Min. 4. Gas Supply Pressure 5 inch w.c. (1.24 kPa) 5.in.609 mm. Top 72 in. 1828 mm.
control knob in for 10 to 15 seconds. Release the control knob. The control knob should pop back out and then remain lit. Note: If the fire does not light, turn the knob to the “OFF” position and wait five (5) minutes before trying again. 3. To turn down the flame, push the control knob in slightly and turn to Medium (medium or Low (small flame). 4. To shut down the fire pit, turn the control knob to the “OFF” position and turn off the tank valve.
TROUBLESHOOTING GUIDE PROBLEM CAUSE REMEDY No Propane Gas at Burner Check that gas tank valve is open. Turn control knob to “ON” and push control knob in. Make sure tank has propane gas. Check that AAA battery is installed with negative (-) end first and has a charge. Check that the wire is connected to the ignition module. Check that the electrode is not cracked or broken.
ONE-YEAR LIMITED WARRANTY What is Covered Under This Warranty? The item you have purchased is warranted against defects in material and workmanship for the following parts from the date of purchase for the period of warranty as outlined below, but only when the unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes: Limited 1 Year • Stainless Tube/Plate burner Limited 90 days • All remaining parts How Do I Obtain Warrant
