AGIO INTERNATIONAL COMPANY LTD. SHUNDE SHIAN FURNITURE INDUSTRIES CO. LTD. PATIO FURNITURE & ACCESSORIES ASSEMBLY INSTRUCTIONS STOP - IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues), please DO NOT RETURN TO THE RETAILER/STORE where you purchased the product. Call our Customer Service Hotline at: 1-800-416-3511 Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday Or visit our website at: www.agio-usa.
ASSEMBLY INSTRUCTIONS CSA Model99010 ARL00200 Installer: Leave these instructions with consumer. Consumer: Keep these instructions for future reference. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: Improper installation, adjustment alteration, service or maintenance can cause injury or property damage.
TABLE OF CONTENTS Important Safety Information 3 Important About Propane 4 Specifications 4 Parts Identification List 5-6 Installation 7-11 Batteries 11 Lighting Instructions 12 Maintenance 12 Troubleshooting Guide 13 Warranty 14 2
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable.
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS A self contained LP-gas cylinder for use with this appliance must have a capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD (overfill protection device). See Figure 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S.
PARTS IDENTIFICATION LIST PART DESCRIPTION PART# QTY A CONTROL KNOB FP1245 1 B GAS VALVE FP0307 1 C THERMOCOUPLE FP0004 1 D LP REGULATOR HOSE 65-FP-0181 1 E ELECTRODE 65-FP-0128 1 F ORIFICE ELBOW FP0310 1 IGNITION MODULE PROPANE ORIFICE “AAA” BATTERY(1.
V TABLE RIM 1 W BACK PANEL 1 X LEFT SIDE PANEL 1 Y RIGHT SIDE PANEL 1 Z DOOR PANEL 1 AA LP SUPPORT 1 BB TILE-1 4 CC TILE-2 4 DD MIDDLE SUPPORT 1 EE TABLE COVER 1 FF BOTTOM/ TOP CONNECTOR 1 6
INSTALLATION 1. Identify parts packed in carton against the parts list. Remove all protective materials and set parts on a flat, non-abrasive surface. 2. Attach the back panel to side panels by using four 1/4"x40 mm bolts and washers as shown in Figure 2. Guide bolts through holes in back panel, into pre-drilled holes in the side panels. Hand tighten only. Figure 2 3. Attach the middle support to the side panels by using two 1/4"x15 mm bolts and washers as shown in Figure 3.
5. Put the door onto the "L" connector (pre-assembled), guide the pin on the lower "L" connector into the hole under the door. Then guide the pin on the upper "L" connector into the hole in the upper portion of the door. Use a 1/4"x15 mm bolt and washer to secure the "L" connector to the right side panel as shown in Figure 5. Do not over tighten. Figure 5 6. With the help of another person, carefully place the table top onto the table base.
8. Place gas tank onto the LP support as shown in Figure 8. Figure 8 9. Attach the metal ring (as shown in Figure 9) pre-fitted with gas hose which is connected to the table top, into the hole of the door panel, then use hex bolt driver to screw 1/4"x5mm nut, the gas tank has fixed as shown in Figure 10. Connect the regulator as shown in Figure10. Screw the black handle clock-wise to tighten. Turn the handle counterclockwise to remove. The hose must point down.
10. After making any necessary adjustments to the parts, use the hex bolt driver to tighten all bolts. Note: each bolt must be tightened a few revolutions at a time. Repeat until all bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts with covers. 11. Note the clear bumpers spaced evenly throughout the inside of the table top. Carefully place tiles inside table rim, resting on the clear bumpers as shown in Figure 11 Figure 11 12.
14. Open the tank valve. Apply a solution of soapy water to the tank-regulator connection and to the valve-hose connection to check for leaks as shown in Figure 14 If soap bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve and tighten all connections. NOTE: NEVER USE A FLAME TO CHECK FOR LEAKS. Checking the tank-regulator for leaks Figure 14 BATTERIES Make sure the control knob is in the "OFF" position.
LIGHTING INSTRUCTIONS Warning: If these instructions are not followed exactly, a fire or explosion may result in causing property damage, personal injury or loss of life. 1. Make sure the control knob is in the "OFF" position. See Figure 16 Open the tank valve all the way. IGNITER BUTTON Figure 16 CONTROL KNOB 2.Push in the igniter button. You will hear a slight clicking sound. With the igniter button pushed in, push and turn the control knob to the “ON” position.
TROUBLESHOOTING GUIDE PROBLEM CAUSE REMEDY No Propane Gas at Burner Check that gas tank valve is open. Turn control knob to “ON” and push control knob in. Make sure tank has propane gas. Burner won’t light No Spark at Electrode Burner won’t stay lit after lighting Check that AAA battery is installed with negative (-) end first and has a charge. Check that the wire is connected to the ignition module. Check that the electrode is not cracked or broken.
90 DAYS LIMITED WARRANTY What is Covered Under This Warranty? The item you have purchased is warranted against defects in materials and workmanship for the following parts as outlined below only when unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes: Burner Assembly Firepit Base Firepit Top How Do I Obtain Warranty Service? To obtain warranty service, you must contact our customer service center within the rel
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!! TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT Step 1: Identify all parts packed in the carton against the parts list. Remove all protective materials. Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are unsure how to proceed with the assembly, call our Customer Service Center at 1-800-416-3511.
CARE AND MAINTENANCE FRAMES Cleaning - Use mild soap and warm water. Do not use abrasive materials, cleansers or bleach products. Rinse with clean water and dry thoroughly. Maintenance - Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to remove all water. This is critical.
