Installation Instructions / Warranty 3-Hole Roman Tub Rough 3-Hole Roman Tub Trim Kits
3-Hole Roman Tub Rough 06607000 Technical Information Recommended water pressure Max. water pressure Recommended hot water temp. Max. hot water temp Hole size in mounting surface valves spout spout retaining pin Max. mounting surface depth Max flow rate 45-80 psi 145 psi 120° - 140° F* 165°F* 1¼" 1⅜" ³⁄₁₆" 1⁹⁄₁₆" 10 gpm *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
Installation Install the connecting tubes Connect the valves to the spout tee using ⅜" compression fittings (included). Tighten the compression fittings wrench tight. Install the rough Remove the plaster shield, spout adapter and gasket from the spout tee. If the mounting surface is unusually, thin, leave the white plastic spacer in place. Otherwise, it may be removed and discarded. Insert the valves and spout tee through the mounting surface. Install the stop rings and escutcheon adapters on the valves.
Trim, 3-Hole Roman Tub Sets Solaris Stratos Metro 06630XX0 06574XX0 06651000 Cross handle Scroll handle Lever handle Swing C 06122XX0 06121XX0 06120XX0 Tango C 06045XX0 06044XX0 06043XX0 Limbo C 06109XX0 06108XX0 06107XX0 These trim kits are for use with rough 06607000. The rough must be installed, and the mounting surface complete and watertight.
06630XX0 06651XX0 Tango C scroll handles shown 06574XX0 Swing C cross handles shown Limbo C lever handles shown
Install the Handles Swing C, Tango C, Limbo C only: Install the deco-rings on the handles. All models: Remove the plaster shields from the hot and cold valves and spout tee. Position the handle over the stem with the lever or cross in the desired “off” position. Hold the lever or cross with one hand. Use the other hand to turn the bell, and screw it down over the valve.
Install the spout Remove the plug from the spout tee. Swing C only: Install the deco-ring on the spout. Make sure that the set screw hole in the deco ring lines up with the set screw hole on the spout. All models: Push the spout sealing ring firmly into the spout tee. Press the spout over the spout tee. Install and tighten the set screw with the enclosed 3 mm Allen wrench. Turn on the water and check all connections for leaks.
Replacement Parts 6 1 2 3 4 5 6 hot cartridge cold cartridge mounting kit mounting kit compression ftg valve set 94009000 94008000 88511000 96080000 88513000 88503000 7 8 9 10 11 12 13 14 sealing ring aerator set screw Solaris handle Stratos handle Metro handle cross handle scroll handle, cold scroll handle, hot lever handle cross handle scroll handle, hot scroll handle, cold lever handle handle deco ring 88512000 13956XX0 96029000 88569XX0 88571XX0 88570XX0 88614XX0 88613XX0 88643XX0 88612XX0 8861
Swing C Tango C 9 9 8 8 7 7 20 19 15 14 13 Limbo C 16 9 17 20 18 7 8
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
LENGTH OF WARRANTY Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as you own the product and the home in which the product is originally installed.
www.hansgrohe-usa.com US - Installation Instructions • Part No. 90964701 • Revised 12/2009 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.