Installation Instructions / Warranty Metris S 04135XX0 Talis S 04136XX0 Allegro E 04139XX0 Metris S 04126XX0 Allegro E 04130XX0 Focus S 04137XX0 Metro E 04140XX0 Talis S 04127XX0 Solaris E 04138XX0 Swing C 04143XX0 Focus S 04128XX0 Metro E 04131XX0 Solaris E 04129XX0 Swing C 04134XX0
Two-hole thermostatic tub filler -- requires rough 04125181 04135XX0 04136XX0 04137XX0 04138XX0 04139XX0 04140XX0 04143XX0
Three-hole thermostatic tub filler -- requires rough 04124181 04126XX0 04127XX0 04128XX0 04129XX0
04130XX0 04131XX0 04134XX0 Technical Information Recommended water pressure Recommended hot water temp. Max. hot water temp Max. flow rate Max. flow rate – handshower Safety stop 45 - 72 psi 120� - 140� F* 165�F* 8 gpm 2.5 gpm 100° F *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater. Installation Considerations • For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber.
Install the valve trim Push the escutcheon over the valve. Install the handle. Tighten the screw with a 3 mm Allen wrench. The screw must engage the slot on the cartridge. Justify the handle. Set the high temperature limit stop. slot Install the spout Remove the plug. Push the spout sealing ring firmly into the spout adapter (1). Push the escutcheon and spout over the adapter and sealing ring (2). Tighten the screw using a 3 mm Allen wrench (3). 3 2 Do not over tighten the set screw.
Install the handshower Pull the end of the handshower hose from the holder. Push the escutcheon over the end of the hose. Push the elbow firmly over one end of the handshower hose. Tighten the hose nut. Thread the hose down through the handshower holder escutcheon and handshower holder. Tighten the escutcheon over the handshower holder. Place the screen washer in the end of the elbow. Connect the handshower to the elbow. Lower the handshower and elbow into the holder.
Set the high temperature limit stop Turn the water on to the tub spout or handshower. Use a 3 mm Allen wrench to loosen the handle screw. Remove the handle from the valve. Carefully remove the retainer clip and the limit stop ring. Turn the temperature control stem until the water is the desired high temperature, usually 110°F* . Turn the stem clockwise to make the water cooler, turn it counter-clockwise to make the water warmer.
Install the stop ring so that it is against the stop -- you should not be able to turn the stem further counter-clockwise. Install the retainer clip. Install the handle. Tighten the screw. Justify the handle. Justify the handle Turn the water on to the tub spout or handshower. Place a thermometer in the water stream. Turn the temperature control knob until the output water temperature is 100°F. Turn the water off.
Loosen the handle screw with a 3 mm Allen wrench. Remove the handle. Hold the handle lever in one hand. With the other hand, turn the temperature control knob until the 100° mark is next to the indexing mark on the handle. Install the handle on the valve. Tighten the screw.
User Instructions - ThermoBalance valve Turn the lever clockwise to send the water to one function, counter-clockwise to send the water to the second function. The center position is off. Turn the temperature control knob clockwise to make the water cooler. Turn the knob counter-clockwise to make the water warmer. function 2 function 1 The knob will stop at the 100° position (the safety stop). To override the stop, press the knob down and continue turning it counter-clockwise.
If scale deposits build up on the spray face, pour about ¾" of a commercial scale remover, such as LimeAway™ or CLR™, into a shallow dish. Follow the label instructions with regard to dilution. Soak the spray face for the amount of time specified in the label instructions. Rinse the handshower with clear water. Install the handshower. Turn on the water and flush the handshower for at least one minute. Maintenance: Clean the filters Turn off the water at the main before opening the valve.
Grasp the wrench flats on the cartridge stop unit with a wrench. Hold the stop unit still with one wrench. Use a second wrench or a 17mm deep socket wrench to unscrew and remove the thermostatic cartridge. Failure to hold the stop unit steady may result in damage to the ceramic plates. Rinse the debris from the filters, using a soft toothbrush if necessary. Do not attempt to remove the screens. Lubricate the o-rings with white plumbers grease. Hold the stop unit steady. Install the thermostatic cartridge.
Replacement parts 1 6 2 13 8 8 7 8 15 16 15 14 12 14 8 12 5 4 13 13 15 15 14 8 8 14 12 12 3 16 15 17 8 18 12 13
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Solaris E handle Talis S handle C handle Metris S handle Focus S handle Allegro E handle Metro E handle handle escutcheon elbow handshower escutcheon check valve spout sealing ring aerator spout escutcheon screw aerator C spout escutcheon for C spout S 100 3-Jet handshower C 100 3-Jet handshower E 100 3-Jet handshower 88530XX0 88549XX0 88610XX0 88713XX0 88714XX0 88719XX0 88721XX0 88734XX0 28071XX0 97159XX0 94074000 88512000 13956XX0 97779XX0 96029000 1
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. (3) Conditions in the home such as excessive water pressure or corrosion. C.