Table of Contents Parts 3 Connection to Computer 4 How to Adjust Monitor Angle 5 Installing Monitor Driver 6 Name and Function of Front 8 Power Management Feature 10 Adjusting OSD 11 Standard Signal Table 17 Specification 18 Troubleshooting 19 Warning 21
INFORMATION TO USER: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cm Look down the monitor below the horizon. LCD Monitor Adjust the monitor to prevent reflection. Relax shoulders and arms, and sit back on the chair. Adjust the monitor stand to acquire required angle.
Connection to Computer How to Adjust Monitor Angle Basic Connection 12V DC connection terminal How to Default Stand Computer cable For PC For Macintosh Use adapter. Adapter for Macintosh (Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution of the monitor. 1. Use 220 V or 110 V. (Free Voltage) 2. Connect monitor and computer via computer cable (See figure 3. Switch on power to monitor and computer. 4. Installation is finished.
Installing Monitor Driver Run (Click) Install at Floppy driver and select the product model to set the optimum display in Window 95, 98 or 2000. Use the Driver Floppy provided. Click 'Advanced..'. Click 'Next>'. Click 'Monitor'. Automatic Installation 1. Insert the Diskette in the Floppy driver. 2. Double-click Install.exe in the Floppy driver folder using search function. 3. Select the model and click "OK". 4. Select inf file of the model in Floppy driver, and then click "OK" button. 5.
Name and Function of Front Front panel Functions Power Switch Power switch is located in the lower center of the monitor stand. You can push the switch to turn on/off the power. Power Saving LED If the green LED around the power switch turns into blinking amber, it indicates the monitor is in power saving mode. On Screen Display (OSD) Function Button OSD buttons on the front of the monitor perform the following functions. MENU : Press this button to display menus.
Power Management Feature When not in use for a long period of time, the monitor automatically reduces its power consumption, meeting power saving standards of EPA and NUTEK. The monitor is equipped with a power saving circuit that conforms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association (VESA). The power management feature requires that the video card of the computer should support DPMS function. Status Adjusting OSD Brightness MENU SELECT 1.
Color Vertical Position MENU SELECT 1. Press the Menu button. 2. Use to move V-Position ICON. 3. Use SELECT button to select it. 4. Use to adjust display upward or downward. MENU SELECT 1. Press the Menu button. 2. Use to move Color ICON. 3. Use SELECT button to select it. 4. Use into the submenu. Clock MENU Preset Color SELECT 1. Press the Menu button. 2. Use to move Clock ICON. 3. Use SELECT button to select it. 4. If Auto-cnfig function fails to remove Video noise, to remove vertical noise.
OSD Overlay Special MENU SELECT SELECT 1. Use to move DOS Overlay ICON. 2. Use SELECT button to select it. 3. Use to adjust DOS Overlay. 4. Press Menu button to exit. 1. Press the Menu button. 2. Use to move SPECIAL ICON. 3. Use SELECT button to select it. 4. Use into the submenu. Zoom Sharpness Video Level SELECT SELECT MENU Language DOS Mode to move DOS Mode ICON. 1. Use 2. Use SELECT button to select it. to select DOS Mode what you want. 3. Use 4. Press Menu button to exit.
Standard Signal Table Auto-Config MENU SELECT 1. Press the Menu button. 2. Use to move the Auto-config ICON. 3. Use SELECT button to select it. 4. Use or to readjust the display condition. In most cass, Auto-Config adjusts display appropriately. Use PH or adjust CLK in accordance with graphic card to fine tune the display. Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) Clock Frequency (MHz) VGA (720 X 400) 31.469 70.087 28.322 VGA (640 X 480) 31.469 59.940 25.
Specification Model l LCD Panel B15BF Type Amorphous active matrix super TFT LCD Screen Size 38.1cm (Diagonal) Maximum Resolution 1024 X 768 @ 75 Hz Pixel Range 0.297 mm X 0.297 mm Display Colors 262,144 Color Contrast Rate 300 : 1 Visual Angle 70° / 70° / 55° / 60° (Left / Right / Up / Down) Response Speed 25 ms Brightness 250 cd/m 2 Synchro Horizontal Frequency nization Vertical Frequency Video Input Video Signal Front Part Power Adapter Wall Mount 18 Power LED is off.
Warning To prevent damage or loss, please read this warning carefully. Color is irregular. Double images or 'ghosts'. Picture is dark. Adjust COLOR at User Mode in OSD Color Menu. When connecting/disconnecting the plug, pull out the plug itself, and never pull the plug to prevent fire caused by short. Check the resolution and frequency of computer and video card, and set up a gain in reference to the current monitor mode and standard signal mode table.
Memo 22
