INFORMATION TO USER : This equipment has bean tested and found to comply with the limits of a Class B hightail device, pursuant fo Part 15 of the FCC Rules. These limits are designed 1o provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference 10 radio communications.
Good Posture Guide + Place the monitor to face the user and then adjust the monitor angle. + Take a break (for about 10 minutes) af every hour during the work with monitor, + Refer to the following figure to take the correct posture. « Look down the monitor below the horizon. o Adjust the monitor to prevent reflection. « Re fax shoulders and ans, ‘and sit back on the chair. * Adjust the mania stand. {0 go quire required angle, » Maintain the ans horizontally and place hands softly on the keyboard.
Correction to Signal Source The range of cilantro Angle ¥ How to Adjust the Stand "Port for AC power table . @Portfolio Eradicable from audio source, i Port for Head Phone or External Speaker Post for signal cable from DVI signal soiree. @ Pennington Lock 1 © Port for signal cable from analog signal source. \\ y 208 &® A Forward 3° Power source connection ®. < Signal cable connection » General ole (Re » For Macintosh # Default na A Backward 30° 1, Use 220V of 110 V. (Free Voltage) 2.
Installing Monitor Prier @ Click ‘Advanced. & Click ‘Mona or, &Lick ‘Change. Click Next> Rater statistics 1. Insert the Diskette fo the Floppy Diskette driver, 2. Double-click "install. exes. 3. Select the model and click "OK" button 4. Select inf file, and then click "OK" button. 5. Click "Exit" button to close the installation. mm @ Click ‘Display a fist of all". © Chick "Have Disk” @ Click Next>. -$B Elect the diver and cock DK Lick Next Click Next: § Click Finish; “or Marriages EET 1.
Name and Function of + Power button Power button is located in the lower center of the Front Bezel. You can push the button totem on/off the power. Power Indicating LED « Dark: Power off « Green : Normal mode Green blinking : DIMS mode or Check Signal Cable mode; + On Screen Display (OSD) Function Button OSI spittoons on the Fort of bagel pepperoni the following functions. # SOURCE : Press this button fo change Analogical display. ® MENU/EXIT : Cross this bunion to display menus.
Ar Power Management Feature ‘The monitor equipped with a power saving circuit that! confirms to the standardization Display Power Manager Signaling (DIMS) made of Video Electronics Standard Association (VESTA: The power mismanagement feature requires that the video card of the computer should support DIMS function. Status LED Sign Power Consumption Normal mode Green ON Narmada Power DIMS mods Green Blinking 1W or Below(Analog)/ 3.5W or Bedfellow) DIMS .¥1 {Option} Mute ON: 1W or 3.
12 English @ Brightness & Contrast Sub menu @ Brightness & Contrast Sub menu [wg MENU. wow woe: SELECT the MENU bunion to access main men. 2. Usg ~ + to move Brightness and Contrast ICON. 3. Press SELECT button inferiority sub menu, Brightness = we fee SELECT wi — 1. Uss = + to nave Brightness ICON. 2. Press SELECT button 10 select it. 3. Use = + to adjust the brightness. “Contrast” oop ree SELECT. mtn mm. Sousa = ¥ to move Contrast (CON: 2. Press SELECT button to select it 3.
ra Bes & Clock Phase Sub menu : ‘Clack Page — + =» SELECT Press = + to move Lock Phase JUN; 2. Use SELECT button fo sectarian it ‘Clock — 4 = SELECT Clock Phase Sub menu 1. Use — + to nova Clock ICON. 2. Press SELECT button to select 1, 3, Press fem ova vertical noise. {Adjusting dock phase is required fare the Insistent of cook MENU. mae om ie SELECT 1. Press MENU bunion 10 access main men, 2.Use + to move Gorgon ICON. 3. Press SELECT bison into the submerse. 14. English 3.
@ Special Sub menu LANGUAGE. PREACHER (AGE Iowa nigh me @® a FACTORY. RESET. Gathering | Vibraharp MODEL: HIBI0034106 16 English se Sang 4 Special Sub menu MENU wae — if fi SELECT oon ope 1, Use = + to move Language ICON. 2. Raga SELECT bunion to'select it. 3. Use + to select language. Factory Rests SELECT 1. Usa — + to nova the Factory Resat ICON, 2. Press SELECT tuition turret to default setting, @ Special Sub menu MENU oe i ee SELECT 1. Use — + lo nave he Information ICON. 2.
‘Solid {Trophy HOT KEY TT MENU SELECT or ili VOL BUTTON Use to move Sound ICON: 2. Press SELECT button foi split i. 3. Use ~ +o control Volume. 4. Press MENU bisection attraction previous slate. 1. When sangs DVI display into. Analog display, select source button vacated in the efi ‘Analog display wilt be shows after Analog input message: 2. When change Analog display lino DVI display. select source button lactated in the loft. DVI display will bo showed after DV input message. 3.
Pin assignment table D-Sub Mini pippin connector Fragrant Conn 1 §-01 [me GEE w) Io 17 2403 Regor PE] eT Eon I oe NC 161 RY input 24 TCE [Fin Na] Assignment [Pin No] Assignment Specification Model B19AF Type Amorphous active matrix super TFT LCD Serene Size 43.20m (Diagonal) Maxi Resorption 280X102 @ 75 Hz Pixel Range 0.264 mm X 0.264 mm won al Display Colors 16.7M Color Contrast Ratio 350:1 Viewing Angle (Left / Right /Up'/ Down) Response.
Troubleshooting : ‘Power L Display is i slat freebie 22~ English EDs dark, LN + Check the power inaction. (Rater 10 page 4) «Adjust COLOR at User Mods in OSD Color Mani + Chick the computer power is on. «Check the resolution and frequency ‘of computer and idea card, and set up again in reference to the current monitor mode and standard signal mods table, «Check the signal cable between monitor and computer, (Rest to page 4 + Adjust COLOR at User Mode in O80 Color Menu.
