Voice ( ) memo / Up button 3. Press the shutter button to start recording and voice will be recorded to the still image for 10 seconds. While the voice is recording, the recording status window will be displayed as shown alongside. 100-0009 STOP:SHUTTER 4. The recording can be stopped by pressing the shutter button again. 5. The ( ) icon will be displayed on the LCD monitor 100-0009 after voice memo recording has finished. - Voice memos can’t be recorded onto movie clip files.
Delete ( ) button ■ This deletes images stored on the memory card. ● Deleting Images in Play Mode 1. Select an image that you want to delete by pressing the LEFT / RIGHT button and press the DELETE( ) button. 2. A message will display as shown alongside on the LCD monitor. 3. Select the submenu values by pressing the UP/DOWN button and then press the OK button. If [Delete] is selected : deletes the selected images. If [Cancel] is selected : cancels "Delete Image".
Left / Right / Menu / OK button ■ LEFT / RIGHT/ MENU/ OK buttons activate the following. - LEFT button : While the menu is showing, press the LEFT button to select the menu tab to the left of the cursor. - RIGHT button : While the menu is showing, press the RIGHT button to select the menu tab to the right of the cursor, or to move an secondary menu. - MENU button : When you press the MENU button, the play mode menu will be displayed on the LCD monitor.
Album button ■ You can organise the captured still images into albums by using the Album button. ■ This camera has 8 albums and each album can take up to 100 images. -0009 ■ The album menu loading time depends on the memory card type. ■ How to use the album ● Selecting the album 1. In the play mode, press the Album button. 2. Select the [Select] menu by pressing the Up/Down button and press the Right button. Select Slide Add Remove Exit:MENU 3.
Album button 3. Select the still images you wish to add by pressing the Up/Down/Left/Right buttons and press the Zoom T button. marks are displayed on the selected images. ※ To cancel the selection, press the Zoom T button again. Select Slide Add Remove Select:T 4. Press the OK button and a confirmation window will display. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [Add] : Inserts the selected images into the album. - [Cancel] : Cancels the inserting images.
Album button ● Playing back the albums ◎ Playing back all of the albums 1. Select [All] menu and press the OK button. All of the albums will be selected. 2. Select [Slide] menu by pressing the Up/Down button and press the Right button. ※ You can select [Start], [Interval], [Repeat] and [Effect] menus. - [Start] : Start the slide show - [Interval] : Set the slide show play interval - [Repeat] : Choose to repeat the slide show after finishing the first cycle.
Setting up the play back function using the LCD monitor ■ PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows. To capture an image after setting up the play menu, press the PLAY mode button or shutter button. Icon Main menu Slide Sub menu Secondary menu Start - Interval 1, 3, 5, 10sec Repeat Off / On Page p.
Setting up the play back function using the LCD monitor Icon Main menu DPOF Sub menu Secondary menu Standard Select/ All Pics/ Cancel Index No/ Yes Size Select/ All Pics/ Cancel No - Yes - Copy to Card Page p.85 p.88 ■ This menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable. Icon Main menu Sub menu Secondary menu One Pic - All Pics - Images No - Yes - Auto Set Page p.90 p.
Setting up the play back function using the LCD monitor Icon Main menu Sub menu Secondary menu Page Auto Plain Type Photo Fastphoto Auto Draft Quality Normal Custom Set p.91 Fine Auto Date Off On Auto File Name Off On Standard - Index - Print DPOF Print Reset No - Yes - No - Yes - ※ Menus are subject to change without prior notice. 《78》 p.92 p.92 p.
Starting the slide show ■ Images can be displayed continuously at pre-set intervals. You can view the slide show by connecting the camera to an external monitor. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Slide] menu tab. ● Start the slide show : The slide show can start only in the [Start] menu. 1. Use the Up/Down buttons to select the [Start] menu. 2. Press the OK button to start the slide show.
Starting the slide show ● Configure slide show effects: Unique screen effects can be used for the slide show. 1. Select the [Effect] sub menu by pressing the UP/ DOWN button and press the RIGHT button. Slide 2. Use the Up/Down Button to select the type of effect. Start Cancel Interval Effect 1 [Cancel] : Normal display. Repeat Effect 2 Effect Effect 3 [Effect 1] : Image is displayed slowly. Effect 4 [Effect 2] : Image is displayed slowly from the centre Back:◀ Set:OK outwards.
Protecting images ■ This is used to protect specific shots from being accidentally erased (Lock). It also unprotects images that have been previously protected (Unlock). ● Protecting Images 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Protect] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Select ] : Selection window for an image to be protected/released is displayed.
Deleting images ■ Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images. Important shots should be stored on a computer before deletion takes place. The startup image is stored in the camera's internal memory (i.e., not on the memory card) and it will not be deleted even if you delete all files on the memory card. ● Deleting images 1. Press the play mode button and press the menu button. 2.
Resize ■ Change the resolution (size) of pictures taken. Select [User image] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Resize] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Rotating an image ■ You can rotate the stored images by various degrees. Once the playback of the rotated picture is finished, it will switch back to the original state. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Rotate] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button.
Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Effect] menu tab. B&W Sepia 3. Select a desired sub menu by pressing the UP/ DOWN Red Green button. Blue [B & W] : Converts the image to black and white. Exit:MENU [Sepia] : Captured images will be stored in a sepia tone (a gradient of yellowish brown colours).
DPOF : Standard ■ This function allows you to embed print quantity information on a stored image. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [Standard] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Select] : Selection window for an image to print is displayed. - Up/Down/Left/Right : Select an image to print.
DPOF : Print size ■ You can specify the print size when printing images stored on the memory card. The [Size] menu is available only for DPOF 1.1 compatible printers. ● Setting the Print Size 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [Size] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Copy To Card ■ This enables you to copy image files to the memory card. ● Copying to the Memory Card 1. Press the play mode button and press the menu button. 2. Select the [Copy to Card] menu tab by pressing the LEFT/ Copy To Card RIGHT button. No Yes 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [No] : Cancels "Copy to Card". Exit:MENU - [Yes] : All images saved in the internal memory are copied to the memory card after the [Please Wait!] message is displayed.
PictBridge ■ You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. Movie clips and voice files cannot be printed. ● Setting up the camera for connection with the printer 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select [Setup] menu tab. 3. Select [USB] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
PictBridge : Picture Selection ■ You can set up the following settings from the PictBridge menu. Images : Select the pictures to be printed. Printer Setup : Setting up printing(Auto Set/ Custom Set) Print : Printing pictures DPOF Print : Printing the DPOF files Reset : Initializing the PictBridge functions ■ Select pictures to print 1. The [Images] menu will appear. 2. Use the UP and DOWN buttons to select the desired One Pic submenu value, and then press the OK button.
PictBridge : Print Setting ■ AUTO SET 1. Use the LEFT and RIGHT buttons to select the [Auto Set] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [No] : [Custom Set] values are kept. [Yes] : All values in the [Custom Set] are automatically changed. Auto Set No Yes Move: ■ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print Quality, Date Print, and File Name Print menus for printed pictures. 1.
PictBridge : Printing ■ Printing Pictures 1. Use the LEFT and RIGHT buttons to select the [Print] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [Standard] : Print the pictures stored in the memory card in set numbers. One picture is printed on one piece of paper. [Index] : Print multiple images on one sheet of paper. 3. The screen shown on the right will appear and the picture will be printed.
PictBridge : RESET ■ Initialises user-changed configurations. 1. Use the LEFT and RIGHT buttons to select the [Reset] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. If [No] is selected : Settings will not be reset. If [Yes] is selected : All print and image settings will be reset. Reset No Yes Move: ※ Default print setting varies depending on the printer manufacturer.
Setup menu ■ In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings. Icon Main menu Sub menu Secondary menu Series - Reset - 1, 3, 5, 10 min - ENGLISH P”CCK»… p.95 File Power Save Language Page 한국어 PORTUGUÊS FRANÇAIS DUTCH DEUTSCH DANSK ESPAÑOL SVENSKA ITALIANO SUOMI p.96 p.
Setup menu Icon Main menu Sub menu Secondary menu Off - On - Dark - Normal - AF Lamp LCD p.100 Bright - NTSC - PAL - Off, 0.5, 1, 3 sec - No - Yes - Video Out Quick View Reset Page p.100 p.101 p.103 p.103 ※ Menus are subject to change without prior notice. File name ■ This function allows the user to select the file naming format. ● Assigning File Names 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup 2.
File name INFORMATION ● The first stored folder name is 100SSCAM, and the first file name is SSL10001. ● File names are assigned sequentially from SSL10001 → SSL10002 → ~ → SSL10099. ● The folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM → 101SSCAM → ~ → 999SSCAM. ● The files used with the memory card conform to the DCF(Design rule for Camera File systems) format.
Language ■ There is a choice of languages that can be displayed on the LCD monitor. Even if the battery and AC charger are removed and inserted again, the language setting will be preserved. ● Setting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. File ENGLISH Power Save 3. Select the [Language] menu by pressing the UP/ DOWN 한국어 Language FRANÇAIS button and press the RIGHT button.
Setting up the Date/ Time/ Date type ■ You can change the date and time that will be displayed on the captured images and set up the date type. ● Setting Date/Time & Selecting Date Format 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup File 2. Press the LEFT/ RIGHT button and select the [Setup] ▲ Power Save menu tab. 05/ 05/ 01 13:01 Language ▼ Format 3. Select the [Date&Time] menu by pressing the UP/ DOWN yy/mm/dd Date&Time button and press the RIGHT button.
Sound ■ If you set the operation sound to ON, various sounds will be activated for camera startup, when button are pressed, and if there is a card error, so that you can be aware of the camera operation status. ● Setting Operation Sounds 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Auto Focus lamp ■ You can turn on and off the Auto Focus lamp ● How to set up the lamp 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [AF Lamp] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. If [Off] is selected : The AF lamp will not light up. If [On] is selected : The AF lamp will light up.
Selecting Video out type ■ The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the camera is connected. PAL mode can support only BDGHI. ● Setting the Video Out Type 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Video Out] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Selecting Video out type INFORMATION ● NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico. ● PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland, Thailand, Norway. ● When using a TV as an external monitor, you will need to select the external or AV channel of the TV. ● There will be a digital noise on the external monitor, but it is not a malfunction.
Quick view ■ If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Quick View] setup. Quick view is possible only with still images. ● Setting Quick View 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup 2. Press the LEFT/ RIGHT button and select the [Setup] USB Off AF Lamp 0.5 sec menu tab. LCD 1 sec Video Out 3 sec 3.
Setting up the Mycam menu ■ You can set up a start up image, start up sound and shutter sound. Every camera working mode (with the exception of Voice recording mode) has the MyCAM menu. The items indicated by are default settings. Icon Main menu Sub menu Page Off LOGO User Image 1 User Image 2 Off Sound 1 Sound 2 Sound 3 Off Sound 1 Sound 2 Sound 3 S.Image p.104 S.Sound p.105 SH.Sound p.105 ※ Menus are subject to change without prior notice.
Start up sound ■ You can select the sound that is activated whenever the camera is turned on. ● Setting the Startup Sound 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Mycam] menu tab. 3. Select the [S.Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. 5. Press the menu button twice and the menu will disappear.
Important notes Be sure to observe the following precautions! ■ This unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt. - Areas exposed to direct sunlight or the inside of a vehicle in hot weather. - Environments where there is high magnetism or excessive vibration. - Areas with high explosives or highly flammable materials.
Important notes ■ Caution on Using the Lens - If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of the image sensor. - Pay attention not to get fingerprints or foreign substances on the surface of the lens. ■ If the digital camera is not used for a long period, an electric discharge can occur. It is a good idea to remove the batteries and the memory card if you do not intend using the camera for an extended period of time.
Warning indicator ■ There are several warnings that may appear on the LCD display Card Error! ㆍMemory card error → Turn off the camera power and turn it on again → Insert the memory card again → Insert the memory card and format the memory card (p.97) Memory Error! ㆍInternal memory error → Turn off the camera power and turn it on again → Format the memory with the memory card removed. (p.
Warning indicator Low Light! ㆍWhen taking pictures in dark places → Take pictures in Flash Photography mode. Set USB ㆍ[USB] sub menu and connected device are not matched. → Reconfigure [USB] in the [Setup] menu. Out Of Number ㆍWhen selecting too many printing pages in the PictBridge menu. → Select printing page within the limitation. Before contacting a service centre ■ Please check the following The camera doesn’t switch on ㆍThere is low battery capacity → Insert charged battery (p.
Before contacting a service centre Camera does not take images when pressing the Shutter button ㆍThere is insufficient memory capacity → Delete unnecessary image files ㆍThe memory card has not been formatted → Format the memory card (p.97) ㆍThe memory card is exhausted → Insert a new memory card ㆍThe memory card is locked → Refer to [Card Locked!] error message (p.108) ㆍThe camera’s power is off → Turn the camera power on ㆍThe batteries are exhausted → Insert charged battery (p.14 ~ 18).
Before contacting a service centre The camera buttons do not operate ㆍCamera malfunction → Remove /re-insert batteries and switch the camera on A card error has occurred while the memory card is in the camera.
Specifications 1/2.5" CCD Approx. 5.0 Mega-pixel Approx. 5.1 Mega-pixel SHD Lens f = 6.6 ~ 19.8mm Focal Length (35mm film equivalent : 39 ~ 117mm) Lens F No. F 3.5 ~ F 4.5 Still Image mode : 1.0X ~ 5.0X Digital Zoom Play mode : 1.0X ~ 10.1X (depends on image size) LCD Monitor 2.
Specifications Media File Format Image Size Storage Capacity (50MB memory card) Image Play Type Editing Interface Power Source Dimensions (WxHxD) Weight Operating Temperature Operating Humidity Software Camera Driver Application Special Features Internal memory : 50MB flash memory External memory : SD card /MMC (Up to 1GM Guaranteed) Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.
Software Notes Please ensure that you read the instruction manual carefully before use. ㆍThe attached software is a camera driver and image editing software tool for Windows. ㆍUnder no circumstances should all or part of either the software or the user manual be reproduced. ㆍCopyrights for software are licensed only for use with a camera. ㆍIn the unlikely event of a manufacturing fault, we will repair or exchange your camera.
About the software After inserting the CD-ROM provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. ■ Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader.
About the software ■ Digimax Reader : Text recognition program. You can save an image file that was captured in the TEXT mode as a text file with this program. This software is only compatible with Windows. ■ PhotoImpression : Image editing program. You can edit or store still images that you download from the camera. This software is only compatible with Windows. INFORMATION ● Be sure to check the system requirements before installing the driver.
Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. INFORMATION ● Close other programs before installing the application software. ● Before installing the application software, disconnect the USB connection. You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.
Setting up the application software 4. If an error listed below takes place during the preview, click the [Install] button to install the XviD codec. - Only a voice plays back. - An error message displays and the movie clip does not play back. * A window shown alongside may display according to the system requirements. [Click !] 5. The XviD codec installation window will be displayed as shown alongside. Click the [Next >] button. [Click !] 6. The Software License Agreement window will be displayed.
Setting up the application software 7. The XviD information window will display. Click the [Next >] button. [Click !] 8. The destination selection window will open. Click [Next >] button. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 9. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button.
Setting up the application software 11. The XviD codec is ready to install. Click the [Install] button. [Click !] 12. Installation is complete. Click the [Finish] button. [Click !] 13. A window where you can choose the program you want to install will appear. Click [Install]. For information on application software, please refer to page 115, 116. [Click !] INFORMATION ● If you select [Exit] at step 13, the application program installation will be cancelled. 14. The [Digimax Viewer 2.
Setting up the application software INFORMATION ● If you select [Cancel] at step 14, a window for installing Digimax Reader will be displayed. 15. The Software License Agreement window will be displayed. If you agree to this, click [Yes], the window will then move to the next step. If you disagree, click [No] and the installation program will be canceled. [Click !] 16. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse..
Setting up the application software 19. A window will be displayed as shown alongside. Click the [INSTALL] button. - Check the [MANUAL] button. Instructions for using Digimax reader will be displayed. - Click the [EXIT] button and Digimax reader installation will be cancelled and a window for installing PhotoImpression will be displayed. [Click !] 20. A window will open. Click the [Next >] button. [Click !] 21. The Software License Agreement window will be displayed.
Setting up the application software 23. Digimax Reader Installation is completed. Click the [Finish] button and PhotoImpression installation will be started. The system will not reboot even if the [Yes, I want to restart the computer now] option is selected. *The real frame 23 can be different with the illustration according to the system requirements. [Click !] 24. The PhotoImpression installation window will be displayed as shown alongside. Click the [OK] button. [Click !] 25.
Setting up the application software 27. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 28. The [Select Components] window will appear. Click [Next >] button. [Click !] 29. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button. If you want to add the program icons to a different folder, choose another folder, and then click [Next >] button.
Setting up the application software 31. To apply changes, you must restart the computer. Select [Yes, I want to restart my computer now], and then click [Finish]. [Click !] 32. After restarting the computer, connect the PC to the camera with the USB cable. 33. Turn the camera power on. [Found New Hardware Wizard] will open and the computer will recognise the camera. * If you have ever installed an image viewer program or your OS is Windows XP, an image viewer program will open.
Setting up the application software INFORMATION ● If you have installed the camera driver, [Found New Hardware Wizard] may not open. ● On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear. In this case, specify "USB Driver" in the CD supplied. (for Windows 98 and 98 SE). ● Before connecting the camera to the PC, You should first install the camera driver. ● After installing the camera driver, you have to restart your PC.
Starting PC mode • If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". • In this mode, you can download stored images to your PC through the USB cable. ■ Connecting the camera to a PC 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3.
Starting PC mode ■ Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable. 2. On your computer's desktop display, select [My computer] and double click [Removable Disk → DCIM → 100SSCAM]. The image files will then be displayed. 3. Select an image and press the right mouse button. 4. A pop-up menu will open. Click [Cut] or [Copy] menu.
Starting PC mode 6. Press the right mouse button and a pop-up menu will open. Click [Paste]. 7. An image file is transferred from the camera to your PC. - By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
Removing the USB Driver for Windows 98SE ■ To remove the USB driver, refer to the process shown below. 1. Trace [Start → Settings] and click [Control Panel]. 2. Double-click [Add/Remove programs]. 3. The [Add/Remove Programs Properties] window will open. Click [Digimax i5] and click the [Add/Remove] button. [Click !] 4. Uninstallation is complete. Click the [Finish] button and the window will disappear.
Removable Disk ■ To use this camera as a Removable Disk, install (p.117) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [Removable Disk] under [My computer] or [Windows Explorer]. 3. Image files stored in the Removable Disk (DCIM → 100SSCAM) can be transferred to the PC. INFORMATION Important information whilst using the Removable Disk ● The [Removable Disk] indicator will not show when the camera power is off or the USB cable is removed.
Removing the removable disk ■ Windows 98SE 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2. Unplug the USB cable. ■ Windows 2000/ME/XP (The illustrations may be different from the real display in accordance with the Windows O/S.) 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2.
Removing the removable disk 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. 7. Unplug the USB cable. [Click !] Setting up the USB Driver for MAC 1. A USB Driver for MAC is not included with the software CD as MAC OS supports the camera driver. 2. Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This camera is compatible with MAC OS 9.2 ~ 10.3. 3.
Digimax Viewer 2.1 ■ This software is only compatible with Windows. 1. To open Digimax Viewer, click the [Start → Programs → Samsung → Digimax Viewer 2.1 → Digimax Viewer 2.1 ] and Digimax Viewer 2.1 will then open. 2. If the [Auto Launch] option is selected, this program will be executed automatically with recognizing the camera. 3. You can easily use the Digimax viewer 2.1 program as it offers a FILE menu and TOOL bar. And, you can use the pop up menu. Click an image and press the right mouse button.
Digimax Reader ■ Digimax Reader is a Text recognition program. You can save an image file that is captured in the Text mode, as a text file with this program. This software is only compatible with Windows. ■ To start the program, click [Start → Programs → Digimax Reader Eng]. The following screen will appear. ■ How to use the Digimax Reader 1. Connect the camera and the PC with a USB cable and download the images that were stored in the camera to the PC.
Digimax Reader 4. Select the image you want to save as a text file. * Only an image that was taken with SAMSUNG camera can be opened. 5. Click the Area Analysis( image. ) icon to scan the 6. Part of the image you selected will be displayed as shown. 7. Click the Character Recognition( ) icon. The part selected in the previous step will be recognized as text. 8. To save the section as a text, click the Save( icon. A window as shown alongside will be displayed.
Digimax Reader 9. Select a file type that you want to. Selectable file type : *.TXT, *.HWP, *.DOC, *.RTF INFORMATION ● To get an image that can be recognized as a text : - Keep a distance of 20cm between the subject and the camera. - The subject need to be centered. - Avoid the camera shake to get a good image. ● Refer to the [Help] menu in Digimax Reader for further information. Using PhotoImpression ㆍWith PhotoImpression, you can edit or store still images that you downloaded from the camera.
Using PhotoImpression ㆍYou can use PhotoImpression to perform the following tasks. ■ Command Button Button Description Imports a picture from an album, a source folder, or the camera/scanner, or captures screen shots of what is being viewed on the current monitor. Selects Cut, Resize, Edit Image, Insert Text, Enhance Picture, Insert Effects, or Layer. Performs Insert Frame, Insert Borders, Insert Calendar, Insert Greeting Cards, Insert Template, or Connect with Other Software.
FAQ ■ Please check the following if the USB connection malfunctions. [Case 1] The camera power is off. → Turn the camera power on. [Case 2] USB Driver is not installed correctly. → Install the USB Driver correctly. Refer to page 117. [Case 3] The USB cable is not connected or you are using a cable with an incorrect specification. → Use a USB cable with the correct specification. [Case 4] The camera is not recognized by your PC.
FAQ There must be USB Host Controller and USB root hub under [Universal Serial Bus controllers]. In addition, double-click on the USB Universal Host Controller and the USB Root Hub to check if the Device Status states "This device is working properly". If the Device Status says the device is "not working properly", click the "Driver" tab and then click [Update Driver] or [Reinstall Driver]. → When all the conditions mentioned above are met, the computer can support the USB interface.
FAQ ■ When the movie clip doesn’t play back on the PC ※When the movie clip recorded by the camera doesn’t play back on the PC, the causes are mostly codec installed on the PC. ●When A codec for play back the movie clip isn’t installed → Install the codec as listed below. [Installing a codec for Windows] 1) Insert the CD provided with the camera 2) Run the windows explorer and select [CD-ROM drive:\Xvid] folder and click the Xvid1.0.2.exe file.
FAQ ● If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly → If a PC (Windows 98) is turned on for a long time and connect the camera repeatedly, the PC may not recognise the camera. In this case, re-start the PC. ● If a PC connected with the camera stops responding while the Windows is starting. → In this case, disconnect the PC and the camera and the windows will start correctly.
MEMO 《143》
SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU, SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 www.samsungcamera.com SAMSUNG OPTO-ELECTRONICS AMERICA, INC. HEADQUARTERS 40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A. TEL : (1) 201-902-0347 FAX : (1) 201-902-9342 WESTERN REGIONAL OFFICE 18600 BROADWICK ST., RANCHO DOMINGUEZ, CA 90220, U.S.A. TEL : (1) 310-900-5263/5264 FAX : (1) 310-537-1566 www.
